摘 要 瞬态仿真领域的许多工作需要获得可视化数据, 仿真电路不能将输出参数绘制成图形时研究工作将受到很大影响. 而权威电路仿真软件PSpice 在这个方面不尽如人意. 本文提出了一种有效的解决办法: 通过MATLAB 编程搭建一个PSpice 与MATLAB 的数据接口,使PSpice输出数据文件可以导入到MATLAB中绘制图形. 这令我们能够很方便地获得数据的规律以有效地分析仿真结果, 这项技术对于教学和工程实践都有比较实际的帮助.关键词: 瞬态仿真 仿真程序 PSpice MATLAB 可视化数据The Data Transfer from Pspice to MATLABWu hao Ning yuanzhong Liang yingAbstract Many works in the area of TRANSIENT simulation has shown how a emulator such asPSpice can be interfaced to an control analysis package such as MATLAB to get viewdata. Thepaper describes how such interfaces can be made using the MATLAB programming. The platformas a typical platform will solve the problem that PSpice software sometimes can not draw the datato a picture. It can make us find the rule from numerous data very expediently, so we can analyzethe outcome of the simulation. And it also can be used in the field of education.Keywords TRANSIENT Simulation Emulator PSpice MATLAB Viewdata1 引言科学研究和工程应用常需要进行电路仿真 PSpice可进行直流 交流 瞬态等基本电路特性分析 也可进行蒙托卡诺 MC 统计分析 最坏情况 Wcase 分析 优化设计等复杂电路特性分析 它是国际上仿真电路的权威软件 而MATLAB的主要特点有 高效方便的矩阵和数组运算 编程效率高 结构化面向对象 方便的绘图功能 用户使用方便 工具箱功能强大 两者各有着重点 两种软件结合应用 对研究工作有很重要的意义香港理工大学Y. S. LEE 等人首先将PSpice和MATLAB结合 开发了电力电子电路优化用的CAD 程序MATSPICE[6] 将两者相结合的关键在于 如何用MATLAB 获取PSpice的仿真数据 对此参考文献 6 里没有详细叙述 本文着重说明用MATLAB 读取PSpice仿真数据的具体方法本论文利用MATLAB对PSpice仿真出的数据处理绘制出后者无法得到或是效果不好的仿真图形 下面就两者结合使用的例子 进行具体说明
上传时间： 2013-10-20
上传用户：wuchunzhong
Semiconductor memory, card readers, microprocessors,disc drives, piezoelectric devices and digitally based systemsfurnish TRANSIENT loads that a voltage regulator mustservice. Ideally, regulator output is invariant during a loadTRANSIENT. In practice, some variation is encountered andbecomes problematic if allowable operating voltage tolerancesare exceeded. This mandates testing the regulatorand its associated support components to verify desiredperformance under TRANSIENT loading conditions. Variousmethods are employable to generate TRANSIENT loads, allowingobservation of regulator response
上传时间： 2013-11-21
上传用户：semi1981
OrCAD_PSpice简明教程1. 介绍 2. 带 OrCAD Capture 的 Pspice 用法 2.1 第一步：在 Capture 中创建电路 2.2 第二步：指定分析和仿真类型 偏置或直流分析（BIAS or DC analysis） 直流扫描仿真（DC Sweep simulation） 2.3 第三步：显示仿真结果 2.4 其他分析类型： 2.4.1 瞬态分析（TRANSIENT Analysis） 2.4.2 交流扫描分析（AC Sweep Analysis） 3. 附加的使用 Pspice 电路的例子 3.1 变压器电路 3.2 使用理想运算放大器的滤波器交流扫描（滤波器电路) 3.3 使用实际运算放大器的滤波器交流扫描（滤波器电路) 3.4 整流电路（峰值检波器）和参量扫描的使用 3.4.1 峰值检波器仿真（Peak Detector simulation） 3.4.2 参量扫描（Parametric Sweep） 3.5 AM 调制信号 3.6 中心抽头变压器 4. 添加和创建库：模型和元件符号文件 4.1 使用和添加厂商库
上传时间： 2022-02-09
上传用户：XuVshu
PW2330 develops a high efficiency synchronous step down DC-DC converter capable of delivering3A output current. PW2330 operates over a wide input voltage range from 4.5V to 30V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss. PW2330 adopts the proprietary instant PWM architecture to achieve fast TRANSIENT responsesfor high step down applications and high efficiency at light loads. In addition, it operates atpseudo-constant frequency of 500kHz under continuous conduction mode to minimize the size ofinductor and capacitor
标签： pw2330
上传时间： 2022-02-11
上传用户：
PW2205 develops a high efficiency synchronous step-down DC-DC converter capable of delivering5A output current. PW2205 operates over a wide input voltage range from 4.5V to 30V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss.PW2205 adopts the instant PWM architecture to achieve fast TRANSIENT responses for high step downapplications and high efficiency at light loads. In addition, it operates at pseudo-constant frequencyof 500kHz under continuous conduction mode to minimize the size of inductor and capacitor
标签： pw2205
上传时间： 2022-02-11
上传用户：
The PW2163 is a high efficiency 500 kHz synchronous step-down DC-DC converter capable ofdelivering 3A current. The PW2163 operates over a wide input voltage range from 4.5V to 18V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss. Low output voltage ripple and small external inductor and capacitor sizes are achieved with 500kHz switching frequency. It adopts the instant PWM architecture to achieve fast TRANSIENT responsesfor high step down applications
标签： pw2163
上传时间： 2022-02-11
上传用户：
Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, TRANSIENT overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional TRANSIENT overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where TRANSIENT overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking requirement. The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "Monitoring and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
标签： agilent
上传时间： 2022-02-20
上传用户：
