单片机作为一种微型计算机，其内部具有一定的存储单元（8031除外），但由于其内部存储单元及端口有限，很多情况下难以满足实际需求。为此介绍一种新的扩展方法，将数据线与地址线合并使用，通过软件控制的方法实现数据线与地址线功能的分时转换，数据线不仅用于传送数据信号，还可作为地址线、控制线，用于传送地址信号和控制信号，从而实现单片机与存储器件的有效连接。以单片机片外256KB数据存储空间的扩展为例，通过该扩展方法，仅用10个I/O端口便可实现，与传统的扩展方法相比，可节约8个I/O端口。 Abstract: As a micro-computer,the SCM internal memory has a certain units(except8031),but because of its internal storage units and the ports are limited,in many cases it can not meet the actual demand.So we introduced a new extension method,the data line and address lines combined through software-controlled approach to realize the time-conversion functions of data lines and address lines,so the data lines not only transmited data signals,but also served as address lines and control lines to transmit address signals and control signals,in order to achieve an effective connection of microcontroller and memory chips.Take microcontroller chip with256KB of data storage space expansion as example,through this extension method,with only10I/O ports it was achieved,compared with the traditional extension methods,this method saves8I/O ports.
上传时间： 2014-12-26
上传用户：adada
首先研究CAN总线和SAE J1939协议，提出一种基于MC9S12HZ256微控制器的总线式汽车数字仪表解决方案。详细介绍SAE J1939协议的报文帧格式及应用层协议中发动机相关参数的定义，以及步进电机及其驱动和车速信号的处理方法。该数字仪表系统硬件平台由微处理器和信号采集和信息处理及显示等模块组成。软件设计部分编程实现了对CAN总线和各传感器数据的读取、处理。该系统能够实时反映车辆工况。 Abstract: In this paper，CAN bus and SAE J1939protocol are researched，and a vehicle digital instrument solution based on MC9S12HZ256MCU is proposed.The message frame format and some engine-related parameters’definition in SAE J1939application layer protocol are introduced in detail.Stepper motor and its driver，the methods of speed signal process-ing are also introduced.The hardware platform of vehicle digital instrument is composed by MCU，signal acquisition mod-ule，and signal processing and displaying module.Data receiving and processing from CAN bus and sensors are accom-plished by programming，and vehicle condition can be reflected in real-time.
上传时间： 2013-10-20
上传用户：huannan88
实时时钟是微机保护装置的重要部件，在讨论PCF8583结构与功能的基础上，提出采用dsPIC33F系列微处理器与串行I2C时钟PCF8583的接口设计方案，给出了相应的接口电路与软件流程。该设计方案结构简单，可靠性高，开发周期短，具有一定的实用与参考价值。所设计的微机保护装置已投入现场运行，效果良好。 Abstract: Real-time clock chip is an important part in microcomputer protection device.Based on discussing the structure and function of PCF8583，a new interface scheme which uses dsPIC33F microprocessor and serial clock chip（I2C）PCF8583is proposed.The method of the circuit design and the main software flow are introduced in this paper.The scheme has simple structure，higher reliability and shorter exploitation cycle，so has definite practicality or reference value.The microcomputer protection device has been put into operation with better effects.
上传时间： 2013-11-18
上传用户：Thuan
介绍一种基于C8051单片机的动态心电监护系统。该系统由两部分组成：以C8051F320单片机为核心的数据采集装置和以PC机为平台的分析处理系统。硬件电路功耗低，由单片机自带的USB接口将数据传送给PC机。软件平台采用LabVIEW可视化虚拟仪器系统开发平台，将传统仪器的功能模块集成到计算机中，用户可通过修改虚拟仪器的程序改变其功能。采用USB接口实时传输心电数据，并将数据采集模块设计为计算机外设，使该系统高速快捷、小巧便携。 Abstract: In this design，a low-cost ECG electrocardiogram monitoring system is introduced，which consists of two parts:data acquisition device based on C8051F320and PC terminal as the analysis and processing system.The system is low-power consumption，the data is transmitted to the PC terminal by USB interface of the C8051F320.By using the visible virtual instrument system developing platform LabVIEW，the traditional instruments function modules are integrated into the computer，so the user can modify virtual instrument software to change its function to meet their needs.Using USB in-terface to realize real-time ECG data transmission，in addition，ECG data acquisition module is designed as the computer peripheral，which makes the syetem high-speed and portable.
上传时间： 2013-11-13
上传用户：zhangzhenyu
针对盘山路存在的转弯盲区，即在转弯时司机无法得知弯路对面是否有车辆通过，设计一种基于C8051F310的山路转弯预防警示系统。该系统利用一阶滤波算法检测山路转弯时是否有车辆通过。运用该算法可增强系统检测的实时性，提高检测机动车辆的灵敏度，同时大大减少环境温度对检测的干扰。试验表明该系统能够正确指示出在山路转弯时是否有车辆通过，目前该系统已安装在盘山路上，可大大减少事故的发生率。 Abstract: Aiming at passing hilly road，there is a turn blind spot.Motormen usually do not know if the passing of vehicles pass the road.So a system of defending accident on hilly road is designed,which is based on MCU C8051F310.The sys-tem uses the first-order filter algorithm to detect whether there are passing vehicles.This algorithm enhances the real-time detection and improves the sensitivity of detection vehicles.Meanwhile,it reduces the detection interference of environmen-tal temperature.The experimental results show that this system can exactly indicate if there are passing vehicles.At present,the system has been successfully applied to hilly road.The system can greatly decrease accident.
上传时间： 2013-10-10
上传用户：归海惜雪
飞机电网故障时，机载电气盒必须在延迟时间内切断电网，保护机载设备。采用AT89S52设计的电气盒测试仪能够测试电气盒保护功能，测量延迟时间。实际应用结果表明，该测试仪具有测量准确、可靠性高、成本低等优点。 Abstract: The helicopter-electrical-box must shut off the helicopter power，protect the equipments of the helicopter when the helicopter power is failed.The tester for the helicopter-electrical-box based on AT89S52is used for testing the protect-ing function and measuring the delay time.Application results show this tester has some advantages,such as accurate mea-surement,high dependability,economical cost etc.
上传时间： 2014-12-27
上传用户：786334970
该系统由单片机89S52控制模块，程控宽带放大模块，整形模块，FPGA内频率、相位差测量模块等构成，采用等精度测频法测出频率和周期，可测量有效值为0.01～5V，频率范围1Hz～20MHz信号的频率、周期信号，精度高达10-6。采用计数法测量相位差，该系统可测量有效值0.5～5V，频率10Hz～100kHz信号的相位差，精度为1°。系统功能由按键控制，测量结果实时显示，人机界面友好。 Abstract: The system consists of the following functional blocks:89S52microcontroller controlling module,programmable amplifier module,comparator module,frequency and phase difference testing module in the FPGA.The system use the equal accuracy frequency-examining technique it measures frequency and circle of signal which its ranges is from1Hz to20MHz and the amplitude of which its range is from0.01Vrms to5Vrms,precision is up to10-6.Using of count method,the system detects the phase difference of signal,the amplitude of whic its range is from0.5Vrms to5Vrms and the frequency of which its ranges is from10Hz to100kHz,precision is up to1°,The system functions is controlled by certain keys,measurement results are displayed in real-time and it is friendly interface.
上传时间： 2013-11-04
上传用户：CHINA526
以89S52单片机和EP1C6Q240C8型FPGA为控制核心的多功能计数器，是由峰值检波、A/D转换、程控放大、比较整形、移相网络部分组成,可实现测量正弦信号的频率、周期和相位差的功能。多功能计数器采用等精度的测量方法，可实现频率为1Hz～10MHz、幅度为0.01～5Vrms的正弦信号的精确测频，以及频率为10Hz～100kHz、幅度为0.5～5Vrms的正弦信号精确测相。液晶显示器能够实时显示当前信号的频率、周期和相位差。该多功能计数器精度高，界面友好，实用性强。 Abstract: A multi-function counter，which uses89S52MCU and EP1C6Q240C8FPGA as a control core，consists of peak detector，A/D conversion，program-controlled amplification，compared shaping and phase-shifting network part.The counter measures the frequency，period and phase of sinusoidal signal.With the equal precision method,the multi-function counter achieves the precise frequency measurement of the sinusoidal signal which its frequency is from1Hz to10MHz，its amplitude is from0.01Vrms to5Vrms，as well as the accurate phase measurement of the sinusoidal signal which its frequency is from10Hz to100kHz，its amplitude is from0.5Vrms to5Vrms.The LCD monitor real-time displays the frequency，period and phase difference of current signal.The multi-function counter features high precision，friendly interface，and strong practical.
上传时间： 2013-11-15
上传用户：gy592333
介绍了当前普通标记机控制系统现状及其存在缺点，给出气动标记机及相频修正PWM模式的工作原理。采用ATmega16单片机和USB转换RS232接口器件CH341T实现驱动控制系统与PC的实时通讯，标记控制系统可升级到USB接口。采用基于ATmega16的相频修正PWM替换555振荡电路产生的PWM，可直接通过软件调整PWM信号。使用达林顿三极管TIP122替代直流继电器驱动高频电磁阀，使得电磁阀驱动电路简单，成本低廉。该控制系统已成功应用于气动标记机。 Abstract: In this paper,the actuality and demerit of the common gas marking machine control systems are described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
上传时间： 2013-10-18
上传用户：1427796291
应用德国Micronas公司的CDC3207G微控制器开发了一款汽车仪表板系统。详细地介绍了该系统的硬件原理，以及步进电机，音频控制，LCD显示，LED指示灯和报警灯等几个模块的实现方法。应用μC/OS-II实时操作系统开发软件。着重介绍了启动代码的设计和任务的规划。 Abstract: A dashboard system is developed by using CDC3207G microcontroller made by Micronas.The hardware of the sys-tem and the realization of the step motor module,audio module,LCD display and LED indicator and alarm module are ex-plained in detail.The μC/OS-II real-time operating system is used for the software development and the starting code design and the task planning is explained specifically.
上传时间： 2013-10-26
上传用户：x4587
