OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上传时间： 2013-10-27
上传用户：落花无痕
模拟集成电路的设计与其说是一门技术，还不如说是一门艺术。它比数字集成电路设计需要更严格的分析和更丰富的直觉。严谨坚实的理论无疑是严格分析能力的基石，而设计者的实践经验无疑是诞生丰富直觉的源泉。这也正足初学者对学习模拟集成电路设计感到困惑并难以驾驭的根本原因。.美国加州大学洛杉机分校(UCLA)Razavi教授凭借着他在美国多所著名大学执教多年的丰富教学经验和在世界知名顶级公司(AT&T，Bell Lab，HP)卓著的研究经历为我们提供了这本优秀的教材。本书自2000午出版以来得到了国内外读者的好评和青睐，被许多国际知名大学选为教科书。同时，由于原著者在世界知名顶级公司的丰富研究经历，使本书也非常适合作为CMOS模拟集成电路设计或相关领域的研究人员和工程技术人员的参考书。... 本书介绍模拟CMOS集成电路的分析与设计。从直观和严密的角度阐述了各种模拟电路的基本原理和概念，同时还阐述了在SOC中模拟电路设计遇到的新问题及电路技术的新发展。本书由浅入深，理论与实际结合，提供了大量现代工业中的设计实例。全书共18章。前10章介绍各种基本模块和运放及其频率响应和噪声。第11章至第13章介绍带隙基准、开关电容电路以及电路的非线性和失配的影响，第14、15章介绍振荡器和锁相环。第16章至18章介绍MOS器件的高阶效应及其模型、CMOS制造工艺和混合信号电路的版图与封装。 1 Introduction to Analog Design 2 Basic MOS Device Physics 3 Single-Stage Amplifiers 4 Differential Amplifiers 5 Passive and Active Current Mirrors 6 Frequency Response of Amplifiers 7 Noise 8 Feedback 9 Operational Amplifiers 10 Stability and Frequency Compensation 11 Bandgap References 12 Introduction to Switched-Capacitor Circuits 13 Nonlinearity and Mismatch 14 Oscillators 15 Phase-Locked Loops 16 Short-Channel Effects and Device Models 17 CMOS Processing Technology 18 Layout and Packaging
上传时间： 2014-12-23
上传用户：杜莹12345
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上传时间： 2013-10-23
上传用户：wushengwu
The CN3052A is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eliminates the need for the external sense resistor and blocking diode.
上传时间： 2013-11-10
上传用户：子虚乌有
In this paper, two types of MMIC voltage controlled oscillators have been successfully demonstrated. The first chip with single tuning diode shows the excellent tuning linearity. The second chip with two tuning diodes can improve the tuning bandwidth.
上传时间： 2013-10-17
上传用户：xjz632
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
上传时间： 2013-10-21
上传用户：ljt101007
The LTC®3562 quad output step-down regulator is designedfor multicore handheld microprocessor applications thatoperate from a single Li-Ion battery. Its four monolithic, higheffi ciency buck regulators support Intel’s mobile CPU P-Stateand C-State energy saving operating modes. The outputvoltages are independently controllable via I2C, and eachoutput can be independently started and shut down. Designerscan choose from power saving pulse-skipping mode orBurst Mode® operation, or select low noise LDO mode. Thespace-saving LTC3562 is available in a 3mm × 3mm QFNpackage and requires few external components.
上传时间： 2013-10-07
上传用户：1583060504
Today’s computer, datacom, and telecom systems demandpower supplies that are effi cient, respond quicklyto load transients and accurately regulate the voltageat the load. For example, load current can be measuredby using the inductor DCR, thus eliminating the needfor a dedicated sense resistor. Inductor DCR sensingincreases effi ciency—especially at heavy load—whilereducing component cost and required board space.The LTC®3856 single-output 2-phase synchronous buckcontroller improves the accuracy of inductor DCR sensingby compensating for changes in DCR due to temperature.
上传时间： 2013-11-05
上传用户：guobing703
Once relegated to the hinterlands of low cost indicatorlights, the LED is again in the spotlight of the lightingworld. LED lighting is now ubiquitous, from car headlightsto USB-powered lava lamps. Car headlights exemplifyapplications that capitalize on the LED’s clear advantages—unwavering high quality light output, tough-assteelrobustness, inherent high effi ciency—while a USBlava lamp exemplifi es applications where only LEDs work.Despite these clear advantages, their requirement forregulated voltage and current make LED driver circuitsmore complex than the venerable light bulb, but some newdevices are closing the gap. For instance, the LTM®8040μModule™ LED driver integrates all the driver circuitryinto a single package, allowing designers to refocus theirtime and effort on the details of lighting design criticalto a product’s success.
上传时间： 2013-10-16
上传用户：togetsomething
High voltage buck DC/DC controllers such as the LTC3890(dual output) and LTC3891 (single output) are popular inautomotive applications due to their extremely wide 4V to60V input voltage range, eliminating the need for a snubberand voltage suppression circuitry. These controllersare also well suited for 48V telecom applications whereno galvanic isolation is required.
上传时间： 2013-10-31
上传用户：wwwe
