一种实用的微机自动配料秤系统:介绍一种由单片机构成的配料秤。叙述了秤的传感器、变送器、信号的变换、硬件原理、软件流程以及和DCS 系统构成的单回路调节系统,此系统可广泛地应用于各行业的配料控制中。关键词:配料秤 单片机 单回路调节系统 DCS 系统 Abstract :A proportioning weigher based on single chip computer is introduced. Sensors , transmitters , signal converting , principle of hardware ,software flowchart of proportioning weigher and single loop control system composed with DCS system are emphasized ,this system can be used in proportioning control of various trades extensively.Key Words :Proportioning Weigher ,Single Chip Computer ,Single Loop Control System ,Distributed Control System
上传时间： 2013-10-12
上传用户：zwei41
The XA-S3 is a member of Philips Semiconductors’ XA (eXtended Architecture) family of high performance 16-bit Single-Chip Microcontrollers. The XA-S3 combines many powerful peripherals on one chip. Therefore, it is suited for general multipurpose high performance embedded control functions.One of the on-chip peripherals is the I2C bus interface. This report describes worked-out driver software (written in C) to program / use the I2C interface of the XA-S3. The driver software, together with a demo program and interface software routines offer the user a quick start in writing a complete I2C - XAS3 system application.
上传时间： 2013-11-10
上传用户：liaofamous
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上传时间： 2014-01-24
上传用户：zl5712176
基于单片机的汽车多功能报警系统设计The Design of Automobile Multi-function AlarmingBased on Single Chip Computer刘法治赵明富宁睡达(河 南 科 技 学 院 ，新 乡 453 00 3)摘要介绍了一种基于单片机控制的汽车多功能报警系统，它能对汽车的润滑系统油压、制动系统气压、冷却系统温度、轮胎欠压及防盗进行自动检测，并在发现异常情况时，发出声光报警。阐述了该报警系统的硬件组成及软件设计方法。关键词单片机传感器数模转换报警Abstract Am ulti-fimctiona utomobilea larnungs ystemb asedo ns inglec hipc omputerco ntorlis in torducedin th isp aper.Th eo ilpr essuero flu bricatesystem, air pressure of braking system, temperature of cooling system, under pressure of tyre and guard against theft， detected automaticaly场thesystem. Audio and visual alarms wil be provided under abnormal conditions厂The hardware composition and software design of the system， described.Keywords Singlec hipc omputer Sensor Digital-t-oanaloguec onversion Alarmin 汽车多功能报苦器硬件系统设计根据 系 统 实际需要和产品性价比，选用ATMEL公司新生产的采用CMOs工艺的低功耗、高性能8位单片机AT89S52作为系统的控制器。AT89S52的片内有8k Bytes LSP Flash闪烁存储器，可进行100(〕次写、擦除操作;256Bytes内部数据存储器(RAM);3 2 根可编程输N输出线;2个可编程全双工串行通道;看门狗(WTD)电路等。系统由传感器、单片机、模数转换器、无线信号发射电路、指示灯驱动电路、声光报警驱动电KD一9563，发出三声二闪光。并触发一个高电平，驱动无线信号发射电路。
上传时间： 2013-11-09
上传用户：gxmm
一种基于ST62单片机的称重显示控制器A Weighing Display Controller Based on ST62 Single Chip Computer祛 FA(上海时博飞奥控制系统有限公司，上海201100)摘要在介绍了基于ST62单片机的基础上，详细描述了称重显控制器的硬件设计和软件设计思路。该控制器结构简单、操作方便、抗扰能力强等优点;具有较好的推广应用价值。关键词称重显示控制仪ST62单片机硬件设计软件设计Abstract Ont heb asiso fin torductiono fST 62s inglec hipc omputer,th ed esignc oncrptof h ardwarea nds oftwarefo rw eighingd isplayc ontorleris d escrbed.The controler features simple structure, ease operation, powerful capability of anti-interference, etc.，it is wealth to be promoted into practicalapplicationsKeywords We妙吨display0 引言ST62s inglec hip Hardwared esign Softwaer design备 份 振 荡器，振荡器保护电路，上电复位及低压检测复称 重 显 示控制器是一种具有数字显示、开关量输出、定值控制和通信功能的以微机为操作核心的称重控制装置。它是电子衡器的重要基础部件，直接影响电子衡器及电子称重系统的功能和性能。与合适的传感器及承重传力复位系统组合可组成配料秤、料斗秤、定值秤、平台秤、汽车秤等，广泛应用于电力、化工、建筑、冶金、交通运输、食品、军工等部门，是进行自动称重配料控制和生产过程自动化必不可少的重要检测、控制装置。随着 称 重 计量自动化水平的提高，对称重显示控制器的要求也越来越高。为实现低漂移、高稳定，本控制器采用低漂移、高增益放大器AD620和高分辨率的A/D转换器CS5550。为提高稳定性和可靠性，采用集成度高的、抗干扰能力强的ST62单片机。
上传时间： 2013-10-29
上传用户：钓鳌牧马
单片机系统“PC”失控的软件措施Software Measure of GettingO uto fC ontrolfo r“PC"in S ingleC hipC omputerS ystem谧 加 春 王 晓 基 雷 小 华(江 西 理 工 大 学机 电 工 程 学 院 ，赣 州 34 10 00)摘要单片机系统在实际工业现场中可能遇到各种干扰和自身的随机性故障。现场恶劣的环境有可能使计算机系统发生异常，计算机程序指针“PC”失控就是常见的故障之一，如果发生“PC”失控，将导致CPI工作混乱，酿成严重的事故。研究了“PC”失控的原因，并指出软件抗干扰的几种方法，有效保证单片机系统的正常工作。关键词单片机“PC”失控抗干扰Abstract Inp racticalin dustrialfi elds,th ereis v ariousin terferencea fectingo perationo fsi nglec hipc omputersy stemsa ndt hec omputersy stems。fac吨random faults饰themselves. It is very common that the severe environment makes the computer systems abnormal. The program counter "PC"gettingo utof co ntorlis on eo fth ec ommonfa ults.If th isoc curs,C PUw ouldb eru nningo utof or deran din torducesse riousan cient.T hec ausesof " PC"geting out of control， studied in this paper and some countermeasures of anti-interference师software are given to ensure single chip computer systemworking properly.Keywords Single。饰computer Porgramc ounter"P C" Anti-interfeernc 在设 计 和 开发单片机系统时，一般难以周全地预计单片机系统在实际工业现场中可能遇到的各种干扰和自身的随机性故障。因此，除了采取防止和抑制干扰的各项措施外，还应该借助于软件措施克服某些干扰，系统还应具备迅速自行恢复的能力。本文介绍的应对单片机系统PC失控的软件措施，设计灵活，节省硬件资源，能保证测控系统长期可靠地运行。MC S- 5 1单片机以其优良的性能价格比大量应用于工业现场测试和控制领域。但是，现场恶劣的环境有可能使计算机系统发生异常，计算机程序指针PC失控就是常见的故障之一，一旦发生PC“走飞”，计算机系统就会出现工作混乱，酿成严重的事故。为 了 在 CP 失控时尽量减少由此带来的不利影响，并尽快使系统恢复正常，需要采取一定的软件措施和硬件措施。常见的硬件措施有“看门狗”电路。软件措施设置的前提条件是:①在干扰作用下，微机系统硬件部分不会受到任何损坏，或者损坏部分设置有监测状态可供查询;②程序区不会受到干扰侵害。单片机系统的程序和表格以及重要的参数均设置在ROM区，不会因干扰的侵人而改变;③ RAM区中的重要数据不会被破坏，或者虽然被破坏，但是可以重新建立。
上传时间： 2013-11-02
上传用户：bhqrd30
Abstract: This application note discusses the development and deployment of 3G cellular femtocell base stations. The technicalchallenges for last-mile residential connectivity and adding system capacity in dense urban environments are discussed, with 3Gfemtocell base stations as a cost-effective solution. Maxim's 3GPP TS25.104-compliant transceiver solution is presented along withcomplete radio reference designs such as RD2550. For more information on the RD2550, see reference design 5364, "FemtocellRadio Reference Designs Using the MAX2550–MAX2553 Transceivers."
标签： Base-Station Applications Single-Chip Transceiver
上传时间： 2013-11-07
上传用户：songrui
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (Single-Chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
The NXP LPC314x combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, three channel10-bit A/D, and a myriad of serial and parallel interfaces in a single chip targeted atconsumer, industrial, medical, and communication markets. To optimize system powerconsumption, the LPC314x have multiple power domains and a very flexible ClockGeneration Unit (CGU) that provides dynamic clock gating and scaling.
上传时间： 2013-10-11
上传用户：yuchunhai1990
The NXP LPC315x combine an 180 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, an integratedaudio codec, Li-ion charger, Real-Time Clock (RTC), and a myriad of serial and parallelinterfaces in a single chip targeted at consumer, industrial, medical, and communicationmarkets. To optimize system power consumption, the LPC315x have multiple powerdomains and a very flexible Clock Generation Unit (CGU) that provides dynamic clockgating and scaling.The LPC315x is implemented as multi-chip module with two side-by-side dies, one fordigital fuctions and one for analog functions, which include a Power Supply Unit (PSU),audio codec, RTC, and Li-ion battery charger.
上传时间： 2014-01-17
上传用户：Altman
