介绍一种基于CAN总线的牵引变电站自动化系统通讯规约的设计，CAN通讯规约采用标准帧，报文采用主动发送和发送查询两种处理形式。该设计在城市轻轨与地铁牵引变电站中的应用表明：可实现间隔层和通讯处理层的数据快速、可靠的交换，提高牵引变电站的安全性和稳定性 。 Abstract: This paper firstly presents a kind of design dealing with communicational protocol to the traction substation automation system based on CAN bus,and then comes up with the ideas that all frames of CAN communicational protocol should adopt the standard frame,and that messages be processed by two ways:sending initiatively and sending quiries.Subway and light rail application shows that the use of the CAN bus is possible to exchange data quickly and reliably between the layers of the middle and the communicational processing,hence to improve the safety and stability of traction substations.
上传时间： 2013-11-07
上传用户：bs2005
该系统由单片机89S52控制模块，程控宽带放大模块，整形模块，FPGA内频率、相位差测量模块等构成，采用等精度测频法测出频率和周期，可测量有效值为0.01～5V，频率范围1Hz～20MHz信号的频率、周期信号，精度高达10-6。采用计数法测量相位差，该系统可测量有效值0.5～5V，频率10Hz～100kHz信号的相位差，精度为1°。系统功能由按键控制，测量结果实时显示，人机界面友好。 Abstract: The system consists of the following functional blocks:89S52microcontroller controlling module,programmable amplifier module,comparator module,frequency and phase difference testing module in the FPGA.The system use the equal accuracy frequency-examining technique it measures frequency and circle of signal which its ranges is from1Hz to20MHz and the amplitude of which its range is from0.01Vrms to5Vrms,precision is up to10-6.Using of count method,the system detects the phase difference of signal,the amplitude of whic its range is from0.5Vrms to5Vrms and the frequency of which its ranges is from10Hz to100kHz,precision is up to1°,The system functions is controlled by certain keys,measurement results are displayed in real-time and it is friendly interface.
上传时间： 2013-11-04
上传用户：CHINA526
以89S52单片机和EP1C6Q240C8型FPGA为控制核心的多功能计数器，是由峰值检波、A/D转换、程控放大、比较整形、移相网络部分组成,可实现测量正弦信号的频率、周期和相位差的功能。多功能计数器采用等精度的测量方法，可实现频率为1Hz～10MHz、幅度为0.01～5Vrms的正弦信号的精确测频，以及频率为10Hz～100kHz、幅度为0.5～5Vrms的正弦信号精确测相。液晶显示器能够实时显示当前信号的频率、周期和相位差。该多功能计数器精度高，界面友好，实用性强。 Abstract: A multi-function counter，which uses89S52MCU and EP1C6Q240C8FPGA as a control core，consists of peak detector，A/D conversion，program-controlled amplification，compared shaping and phase-shifting network part.The counter measures the frequency，period and phase of sinusoidal signal.With the equal precision method,the multi-function counter achieves the precise frequency measurement of the sinusoidal signal which its frequency is from1Hz to10MHz，its amplitude is from0.01Vrms to5Vrms，as well as the accurate phase measurement of the sinusoidal signal which its frequency is from10Hz to100kHz，its amplitude is from0.5Vrms to5Vrms.The LCD monitor real-time displays the frequency，period and phase difference of current signal.The multi-function counter features high precision，friendly interface，and strong practical.
上传时间： 2013-11-15
上传用户：gy592333
介绍了当前普通标记机控制系统现状及其存在缺点，给出气动标记机及相频修正PWM模式的工作原理。采用ATmega16单片机和USB转换RS232接口器件CH341T实现驱动控制系统与PC的实时通讯，标记控制系统可升级到USB接口。采用基于ATmega16的相频修正PWM替换555振荡电路产生的PWM，可直接通过软件调整PWM信号。使用达林顿三极管TIP122替代直流继电器驱动高频电磁阀，使得电磁阀驱动电路简单，成本低廉。该控制系统已成功应用于气动标记机。 Abstract: In this paper,the actuality and demerit of the common gas marking machine control systems are described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
上传时间： 2013-10-18
上传用户：1427796291
介绍一种基于C8051F060单片机和NAND Flash的数据采集存储系统，该系统可实现3路信号采样，每路采样率为5KS/s,通过异步串行通信接口实现数据传输。并详细说明系统的软件设计。 Abstract: An acquisition and storage system based on C8051F060and NAND Flash is designed in this paper.The system is used to sample three-channel of signal,5KSPS each channel,and can upload data to test bench through UART（Universal Asynchronous Receiver/Transmitter）.The software design is discussed in detail.
上传时间： 2013-10-12
上传用户：Jesse_嘉伟
介绍了采用ATmega48单片机实现三相无刷直流电机控制器的方法。利用Atmega48获得带死区的脉宽调制（PWM）、霍尔传感器的换相处理、正弦驱动信号的产生和电机转速的控制等功能。采用该方法的优点是所需的外围器件少，成本低。 Abstract: The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
上传时间： 2013-12-09
上传用户：330402686
介绍了一种基于C8051F020单片机的多路压力测量仪。该测量仪选用电阻应变式压力传感器采集压力信号，并经放大电路处理后送入C8051F020单片机，再由C8051F020单片机内部的A/D转换器将采集到的压力信号进行模数转化，然后分别对数据进行存储和显示。该测量仪能测量6路压力信号，并且各测量点都能单独检测和设置。由于采用了C8051F020单片机，简化了硬件电路，增强了抗干扰能力，使得测量仪具有测量精度高，冲击小等特点。 Abstract: A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
上传时间： 2013-11-16
上传用户：yare
MMC/SD卡以其优越的性能，在单片机嵌入式设备中得到广泛应用。将MMC/SD卡作为外部掉电存储介质应用于音频信号发生器中，通过8051F330单片机上的SPI接口，实现单片机—MMC/SD卡的存储扩展，设计了此硬件平台上的MMC/SD卡的单片机驱动程序，并给出了相应的程序代码，满足音频信号发生器的大容量存储要求。 Abstract: MMC/SD card is more and more widely used in the single chip embedded devices for their excellent performances.This article introduces the application of MMC/SD card as the external power down storage medium in audio signal generator. The extension technology especially for storage of single chip-MMC/SD card via SPI interfaces in 8051F330 single chip, including designs single chip drive program of MMC/SD card based on hardware platform,and also gives the key coding of the program. The implementation of big capacity storage is meaningful in audio signal generator.
上传时间： 2014-12-27
上传用户：黄华强
针对众多低成本数据采集需求，采用带有片上USB控制器和D/A转换器的混合信号微处理器C8051F340，设计了一款可通过USB接口和LabVIEW图形用户界面实现与PC机联机的数据采集器，同时借助系统的SD卡存储独立实现现场长时间采集数据。该数据采集器成本低，结构简单，体积小，已成功用于工业现场。 Abstract: Aiming at the need of low cost data acquisition, a data acquisition device is designed based on C8051F340 which is a mixed-signal microcontroller and integrates USB controller and A/D controller on a chip.The data acquisition device which can combine with PC by USB interface and LabVIEW graphical user interface,can realize data acquisition. At the same time,it can be solely run a long time in virtue of SD card in field.The date aequisition device features low cost,simple structure and little sharp, and it has been used in industry field.
上传时间： 2014-05-31
上传用户：1109003457
针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移，一般采用光电轴角编码器检测位置信号，输出正交编码脉冲信号。若采用其他方法检测位置信号，必然导致电路设计复杂，可靠性降低。因此，提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理，LS7266R1与单片机的接口硬件设计，以及主程序软件流程图。巧妙地把力量传感器，位移传感器等机械运动状态的压力或拉力以及位置坐标，变成了电压信号和电脉冲数字信号，供A/D测量和LS7266R1计数，从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上传时间： 2013-11-02
上传用户：yl1140vista
