没事多学习一下英语
上传时间： 2013-10-29
上传用户：ukuk
Industrial systems demand semiconductors that are precise, flexibleand reliable. Linear Technology offers a broad line of high performanceanalog ICs that simplify system design with rugged devices featuringparameters fully guaranteed over the -40°C to 85°C temperature range.We back this up with knowledgeable applications support, long productlife cycles and superior on-time delivery.
上传时间： 2013-11-02
上传用户：xiaodu1124
Abstract: This application note describes how sampling clock jitter (time interval error or "TIE jitter") affectsthe performance of delta-sigma digital-to-analog converters (DACs). New insights explain the importanceof separately specifying low-frequency (< 2x passband frequency) and high-frequency or wideband (> 2xpassband frequency) jitter tolerance in these devices. The article also provides an application example ofa simple highly jittered cycle-skipped sampling clock and describes a method for generating a properbroadband jittered clock. The document then goes on to compare Maxim's audio DAC jitter tolerance tocompetitor audio DACs. Maxim's exceptionally high jitter tolerance allows very simple and low-cost sampleclock implementations.
上传时间： 2013-10-25
上传用户：banyou
Abstract: For many first-time users, finding the right logger that meets their needs can be a challenging task. In simple
上传时间： 2014-01-19
上传用户：缥缈
Abstract: This application note presents an overview of the operational characteristics of accurate I²C real-time clocks (RTCs),including the DS3231, DS3231M, and DS3232. It focuses on general application guidelines that facilitate use of device resources forpower management, I²C communication circuit configurations, and I²C characteristics relative to device power-up sequences andinitializations. Additional discussions on decoupling are provided to support developing strategies for mitigating power-supply pushingof device frequency.
上传时间： 2013-11-23
上传用户：WMC_geophy
Digital convergence, in recent history, has been prevalentin the consumer equipment domain and the designengineers in this area have been struggling with a plethoraof emerging standards and protocols. What lessons can welearn from their struggle? The same dilemmas now existin in-vehicle telematics and infotainment systems but withthe added issues of extremes of temperature, safety,security, and time in market.
上传时间： 2014-12-23
上传用户：9牛10
The STM32F10xxx microcontroller family embeds up to three advanced 12-bit ADCs (depending on the device) with a conversion time down to 1 μs. A self-calibration feature is provided to enhance ADC accuracy versus environmental condition changes.
上传时间： 2014-12-23
上传用户：eastimage
Control systems are becoming increasingly dependent on digital processing and so require sensors able to provide direct digital inputs. Sensors based on time measurement, having outputs based on a frequency or phase, have an advantage over conventional analogue sensors in that their outputs can be measured directly in digital systems by pulse counting.
上传时间： 2013-10-08
上传用户：wuyuying
A complete design for a data acquisition card for the IBM PC is detailed in this application note. Additionally, C language code is provided to allow sampling of data at speed of more than 20kHz. The speed limitation is strictly based on the execution speed of the "C" data acquisition loop. A "Turbo" XT can acquire data at speeds greater than 20kHz. Machines with 80286 and 80386 processors can go faster than 20kHz. The computer that was used as a test bed in this application was an XT running at 4.77MHz and therefore all system timing and acquisition time measurements are based on a 4.77MHz clock speed.
上传时间： 2013-10-29
上传用户：BOBOniu
Sensors for pressure, load, temperature, acceleration andmany other physical quantities often take the form of aWheatstone bridge. These sensors can be extremely linearand stable over time and temperature. However, mostthings in nature are only linear if you don’t bend them toomuch. In the case of a load cell, Hooke’s law states that thestrain in a material is proportional to the applied stress—as long as the stress is nowhere near the material’s yieldpoint (the “point of no return” where the material ispermanently deformed).
上传时间： 2013-11-13
上传用户：墙角有棵树
