The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
The TL2575 and TL2575HV represent superior alternatives to popular three-terminal linear regulators. Due totheir high efficiency, the devices significantly reduce the size of the heatsink and, in many cases, no heatsink isrequired. Optimized for use with standard series of inductors available from several different manufacturers, theTL2575 and TL2575HV greatly simplify the design of switch-mode power supplies by requiring a minimaladdition of only four to six external components for operation.
标签： STEP-DOWN SWITCHING SIMPLE 1A
上传时间： 2013-11-20
上传用户：jelenecheung
针对飞行模拟器座舱数据采集的复杂性，设计了一种基于以太网分布式的数据采集控制系统，该系统是RCM5700微处理器模块上的以太网应用。在系统的基础上具体讨论了PoE技术的应用，在传输数据的网线上同时提供电流，提出并实现了一种包括辅助电源在内的完整可靠的PoE供电方案。设计采用美国国家半导体的LM5073和LM5576并根据不同的负载情况，进行稳定可靠的电压转换，以满足数据采集电路的要求。实验结果表明：该设计稳定可靠，满足低于13 W的采集节点供电要求，提高了模拟器信号采集系统的通用性和标准化程度，避免了以往数据采集节点单独繁琐的电源设计。 Abstract: Aiming at the complexity of large avion simulation and controlling，the simulator cabin distribute data collecting and control system was designed. This system is the application of RCM5700 on Ethernet. Based on this system，PoE technique that makes Ethernet can also provide power were expounded with emphasis and included FAUX design the PoE resolution was realized. To achieve the requirement of this system，LM5073 and LM5576 were used to DC-DC switch. From the data of experiment，the design filled the requirement of power-need of node whose power was lower than 13W. The application of the technique can advance the degree of simulation data collections currency and standardization and avoid designing additional power system.
上传时间： 2013-11-09
上传用户：xyipie
多远程二极管温度传感器-Design Considerations for pc thermal management Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two interrupt outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
标签： Considerat Design 远程 二极管
上传时间： 2014-12-21
上传用户：ljd123456
When I started writing the first edition of RF Power Amplifiers for Wireless Communications,some time back in 1997, it seemed that I was roaming a largely uninhabitedlandscape. For reasons still not clear to me there were few, if any, otherbooks dedicated to the subject of RF power amplifiers. Right at the same time, however,hundreds of engineers were being assigned projects to design PAs for wirelesscommunications products. It was not, therefore, especially difficult to be successfulwith a book that was fortuitously at the right place and the right time.
标签： Communications Amplifiers Wireless Edition
上传时间： 2013-11-12
上传用户：YYRR
Abstract: This application note discusses a design for a phantom antenna power-supply system compatible with theDigital Satellite Equipment Control (DiSEqC) communication standard, using the MAX16948 automotive dual, highvoltageLDO/switch. The presented application circuit provides a remote antenna power supply and also enables onewaycommunication from the radio head unit to the remote antenna. This system architecture offers flexibility inDiSEqC tone-burst frequency choice (100Hz to 30kHz), enabling users the ability to select the best frequency for theirapplication.
上传时间： 2013-11-17
上传用户：fnhhs
Chipcon CC2420 reference design w/PA board rev B CC2420_w_PA_PCB.ZIP FABRICATION.PHO - fabrication drawing COPPER1.PHO - copper layer #1 (top side) COPPER2.PHO - copper layer #2 (inner ground plane) COPPER3.PHO - copper layer #3 (inner power plane) COPPER4.PHO - copper layer #4 (bottom side) TOPMASK.PHO - top side solder mask BOTTOMMASK.PHO - bottom side solder mask NCDRILL.DRL - drill data file NCDRILL.LST - drill list NCDRILL.REP - drill report
标签： 2420 FABRICATION reference fabricati
上传时间： 2015-05-12
上传用户：xc216
This text surrounds the development of the electric power SCADA system exactly, aiming at the present condition of the our country electric power charged barbed wire net currently, according to the oneself at the e- lectric power protect the profession after the electricity in seven years of development, design and adjust to try the experience on the scene from following severals carry on the treatise:Is the emergence to the system of SC- ADA and developments to introduce first Carry on the introduction elucidation to applied present condition and the development foregrounds of various terminal equipments communication agreement(rules invite) the next in order Then is the elucidation to the windows the bottom according to the mfc the plait distance environment an- d VC++6.0 plait distance softwares Carry on the more detailed treatise to the realization of the procedure struct- ure frame and the source code again End is the applied case example give examples.
标签： the development surrounds electric
上传时间： 2014-10-28
上传用户：liuchee
ARM7硬件说明与开发 The ARM7 is a low-power, general purpose 32-bit RISC microprocessor macrocell for use in application or customer-specific integrated circuts (ASICs or CSICs). Its simple, elegant and fully static design is particularly suitable for cost and power-sensitive applications. The ARM7’s small die size makes it ideal for integrating into a larger custom chip that could also contain RAM, ROM, logic, DSP and other cells.
标签： ARM7 microprocessor low-power macrocell
上传时间： 2013-12-17
上传用户：3到15
This paper presents a low-power asynchronous implementation of the 80C51 microcontroller. It was realized in a 0.5 µ m CMOS process and it shows a power advantage of a factor 4 compared to a recent synchronous implementation in the same technology. The chip is fully bit compatible with the synchronous implementation, and timing compatible for external memory access. The circuit is a compiled VLSI-program, using Tangram as VLSI-programming language and the Tangram tool set to compile the design automatically to a standard-cell netlist. This design approach proves to be powerful enough to describe the microcontroller and derive an efficient implementation. Further, it offers the designer the possibility to explore various alternatives in the design space.
标签： microcontroller implementation asynchronous low-power
上传时间： 2016-06-07
上传用户：冇尾飞铊
