For power electronic design
上传时间： 2014-12-24
上传用户：1234321@q
This document presents design techniques and reference circuits that power Virtex™-4 FXRocketIO™ multi-gigabit transceivers (MGTs) operating at data rates below 3.125 Gb/s.When using multiple transceivers, it is sometimes preferred to power them from a switchingpower supply. However, switching power supplies generate noise that affects transceiver
上传时间： 2013-11-18
上传用户：huang111
Abstract: It is critically important that lithium-ion battery stacks have a good battery-management system for monitoring many cellvoltages and cell temperatures. Without that monitoring, thermal runaway can lead to a battery explosion. This design idea presentsa low-power circuit that measures the temperature of up to 12 thermistors. It powers and configures the multiplexers, and also putsthe muxes into shutdown to save power when not measuring temperatures.
上传时间： 2013-10-29
上传用户：xwd2010
Achieving High Power Density Designs
标签： Achieving Density Designs Power
上传时间： 2013-10-12
上传用户：qazxsw
The MAX14885E, a 2:2 VGA switch, connects a VGA source to a VGA monitor. To ease direct connection to graphics controllers orthe ASIC, the MAX14885E has two supplies: VCC, a 5V ±5% supply, drives the VGA side interface; and the VL supply sets the logicswitching thresholds on the digital input pins (EN, S00, S01, S10, S11, SHA, SHB, SVA, and SVB). This application note documentsthe proper sequencing of the VCC and VL power supplies on power-up.
上传时间： 2013-10-23
上传用户：wuchunzhong
Multiple-voltage electronics systems often requirecomplex supply voltage tracking or sequencing, whichif not met, can result in system faults or even permanentfailures in the fi eld. The design diffi culties in meetingthese requirements are often compounded in distributedpowerarchitectures where point-of-load (POL) DC/DCconverters or linear regulators are scattered across PCboard space, sometimes on different board planes. Theproblem is that power supply circuitry is often the lastcircuitry to be designed into the board, and it must beshoehorned into whatever little board real estate is left.Often, a simple, drop-in, fl exible solution is needed tomeet these requirements.
上传时间： 2013-10-08
上传用户：15071087253
Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.
上传时间： 2013-10-18
上传用户：avensy
Handheld designers often grapple with ways to de-bounceand control the on/off pushbutton of portable devices.Traditional de-bounce designs use discrete logic, fl ipflops, resistors and capacitors. Other designs includean onboard microprocessor and discrete comparatorswhich continuously consume battery power. For highvoltage multicell battery applications, a high voltageLDO is needed to drive the low voltage devices. All thisextra circuitry not only increases required board spaceand design complexity, but also drains the battery whenthe handheld device is turned off. Linear Technology addressesthis pushbutton interface challenge with a pairof tiny pushbutton controllers.
上传时间： 2013-11-18
上传用户：ZJX5201314
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间： 2013-11-18
上传用户：hulee
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
