为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe SUPPLY controlled by microcontroller is designed. The charger is flyback switching power SUPPLY and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
提出了一种以S3C2440A为核心处理器的银行评价器的设计方案，并结合XILINX公司的XL95144XL型CPLD，辅助S3C2440A，实现该银行评价器的各部分功能以及系统信号之间的相互协调。该评价器在系统设计上采用液晶屏显示，代替了以往简单的数码管电路的显示模式，在视觉上给人以全新的享受。同时，评价器增加了新的网络供电方式，只要将评价器连接上网络就可以正常工作，方便了客户的使用。总之，此款银行评价器采用了嵌入式系统的设计方案，大大丰富了系统功能，实现一个银行评价器设计的新突破。 Abstract: S3C2440A of SamSung company is the core component of the embedded system. A design of bank assessor based on S3C2440A was provided in this paper. It used XL95144XL combined with S3C2440A to realize all the functions and coordination with system signals. This bank assessor used LCD to display instead of the former simple digital display and provided a new seusuous enjoment. Meanwhile，it provided a new method of network power SUPPLY，that the bank assessor could regularly work once it connected to the network，which is convenient for customers to use. In a word，this assessor takes embedded system，enriches the system’s functions and reclizes a new breakout.
标签： S3C2440A
上传时间： 2013-11-03
上传用户：taa123456
为了解决磁放大器性能测试过程中，需要对其供给不同数值恒定电流的问题，设计了一种基于DAC7512和单片机的数控恒流源系统。该系统采用AT89C51作为主控器件，将计算机发送的电流控制字命令转换为D/A转换器控制字，通过模拟SPI通信接口，写D/A控制字到DAC7512，从而控制其输出相应数字电压值，经差动缩放电路、电压/电路变换电路和功率驱动电路，最后输出恒定电流。实验结果表明，恒流源输出电流调节范围为-45~+45 mA、精度为±0.1 mA，分辨率达0.024 4 mA，具有应用灵活，外围电路简单，可靠性高的特点。该数控直流恒流源也可为相关产品的测试系统研发提供参考。 Abstract: In order to solve the need to SUPPLY different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
上传时间： 2014-12-27
上传用户：invtnewer
1 FEATURES· Single chip LCD controller/driver· 1 or 2-line display of up to 24 characters per line, or2 or 4 lines of up to 12 characters per line· 5 ′ 7 character format plus cursor; 5 ′ 8 for kana(Japanese syllabary) and user defined symbols· On-chip:– generation of LCD SUPPLY voltage (external SUPPLYalso possible)– generation of intermediate LCD bias voltages– oscillator requires no external components (externalclock also possible)· Display data RAM: 80 characters· Character generator ROM: 240 characters· Character generator RAM: 16 characters· 4 or 8-bit parallel bus or 2-wire I2C-bus interface· CMOS/TTL compatible· 32 row, 60 column outputs· MUX rates 1 : 32 and 1 : 16· Uses common 11 code instruction set· Logic SUPPLY voltage range, VDD - VSS: 2.5 to 6 V· Display SUPPLY voltage range, VDD - VLCD: 3.5 to 9 V· Low power consumption· I2C-bus address: 011101 SA0.
上传时间： 2013-11-08
上传用户：laozhanshi111
The SN65LBC170 and SN75LBC170 aremonolithic integrated circuits designed forbidirectional data communication on multipointbus-transmission lines. Potential applicationsinclude serial or parallel data transmission, cabledperipheral buses with twin axial, ribbon, ortwisted-pair cabling. These devices are suitablefor FAST-20 SCSI and can transmit or receivedata pulses as short as 25 ns, with skew lessthan 3 ns.These devices combine three 3-state differentialline drivers and three differential input linereceivers, all of which operate from a single 5-Vpower SUPPLY.The driver differential outputs and the receiverdifferential inputs are connected internally to formthree differential input/output (I/O) bus ports thatare designed to offer minimum loading to the buswhenever the driver is disabled or VCC = 0. Theseports feature a wide common-mode voltage rangemaking the device suitable for party-lineapplications over long cable runs.
上传时间： 2013-10-13
上传用户：ytulpx
FEATURES400 MSPS internal clock speedIntegrated 10-bit DAC32-bit tuning wordPhase noise ≤ –120 dBc/Hz @ 1 kHz offset (DAC output)Excellent dynamic performance>75 dB SFDR @ 160 MHz (±100 kHz offset) AOUTSerial I/O control1.8 V power SUPPLYSoftware and hardware controlled power-down48-lead TQFP/EP packageSupport for 5 V input levels on most digital inputsPLL REFCLK multiplier (4× to 20×)Internal oscillator; can be driven by a single crystalPhase modulation capabilityMultichip synchronization
上传时间： 2014-12-04
上传用户：axin881314
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power SUPPLY is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power SUPPLY is required. The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
上传时间： 2013-10-28
上传用户：13691535575
The PCA9534 is a 16-pin CMOS device that provide 8 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower SUPPLY current, individual I/O configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.
上传时间： 2013-11-17
上传用户：vodssv
The CAT823, CAT824, and CAT825 provide basic reset and monitoring functions for the electronic systems. Each device monitors the system voltage and maintains a reset output until that voltage reaches the device’s specified trip value and then maintains the reset output active condition until the device’s internal timer, after a minimum timer of 140ms; toallow the systems power SUPPLY to stabilize.
上传时间： 2014-11-18
上传用户：BOBOniu
