边坡稳定分析小程序SLOPE相当不错的
上传时间： 2015-08-27
上传用户：aa17807091
实现对InSAR复相位信号进行基于局部频率估计的“斜坡自适应（SLOPE-adapt）滤波” 此滤波方法特别适用于InSAR相位图滤波，能在最大限度保持有用信息的条件下滤除各种噪声。
标签： InSAR SLOPE-adapt 滤波 相位信号
上传时间： 2014-01-25
上传用户：mpquest
Differential Nonlinearity: Ideally, any two adjacent digitalcodes correspond to output analog voltages that are exactlyone LSB apart. Differential non-linearity is a measure of theworst case deviation from the ideal 1 LSB step. For example,a DAC with a 1.5 LSB output change for a 1 LSB digital codechange exhibits 1⁄2 LSB differential non-linearity. Differentialnon-linearity may be expressed in fractional bits or as a percentageof full scale. A differential non-linearity greater than1 LSB will lead to a non-monotonic transfer function in aDAC.Gain Error (Full Scale Error): The difference between theoutput voltage (or current) with full scale input code and theideal voltage (or current) that should exist with a full scale inputcode.Gain Temperature Coefficient (Full Scale TemperatureCoefficient): Change in gain error divided by change in temperature.Usually expressed in parts per million per degreeCelsius (ppm/°C).Integral Nonlinearity (Linearity Error): Worst case deviationfrom the line between the endpoints (zero and full scale).Can be expressed as a percentage of full scale or in fractionof an LSB.LSB (Lease-Significant Bit): In a binary coded system thisis the bit that carries the smallest value or weight. Its value isthe full scale voltage (or current) divided by 2n, where n is theresolution of the converter.Monotonicity: A monotonic function has a SLOPE whose signdoes not change. A monotonic DAC has an output thatchanges in the same direction (or remains constant) for eachincrease in the input code. the converse is true for decreasing codes.
标签： Converters Defini DAC
上传时间： 2013-10-30
上传用户：stvnash
WDT ，Flash ，FLL+ ，Timer，Comp_A SLOPE ADC to Detect Tempclockworked
标签： WDT
上传时间： 2014-12-20
上传用户：asasasas
MSP430超低功耗微处理器是TI公司推出的一种新型单片机。它具有16位精简指令结构，内含12位快速ADC/SLOPE ADC,内含60K字节FLASH ROM，2K字节RAM，片内资源丰富，有ADC、PWM、若干TIME、串行口、WATCHDOG、比较器、模拟信号，有多种省电模式，功耗特别小，一颗电池可工作10年。开发简单，仿真器价格低廉，不需昂贵的编程器。
上传时间： 2014-12-22
上传用户：731140412
The AP2406 is a 1.5Mhz constant frequency, SLOPE compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an external Schottky diode. It is ideal for powering portable equipment that runs from a single cell lithium-Ion (Li+) battery. The AP2406 can supply 600mA of load current from a 2.5V to 5.5V input voltage. The output voltage can be regulated as low as 0.6V. The AP2406 can also run at 100% duty cycle for low dropout operation, extending battery life in portable system. Idle mode operation at light loads provides very low output ripple voltage for noise sensitive applications. The AP2406 is offered in a low profile (1mm) 5-pin, thin SOT package, and is available in an adjustable version and fixed output voltage of 1.2V, 1.5V and 1.8V
上传时间： 2017-02-23
上传用户：w124141
1、引言SFP光模块的数字诊断监测主要是对光模块的供电电压、模块温度、偏置电流、接收光功率、发射光功率等5个模拟参量和各种监控信号实时监测。通过分析数字化测量结果判断光模块的通信工作状况，这有利于光通信链路的维护目前大部分设计方案是采用MAXIM公司的DS1859，该芯片完全兼容SFF-8472协议，功能齐全，软件编程简便，但是该芯片价格比较贵，同样很多空间已固定，不灵活，扩展性不好，对于以后版本的升级不方便。本方案采用一片MCU，EEPROM，数字控制电位器（DCP）替代DS1859，使用软件编程达到满足SFF-8472协议要求，用FLASH存储A2H地址内容以及内外部校准相结合的新校准思想，具有性价比高，可靠性好，扩展性好，校准快速简便等优点本文首先介绍五个模拟量的一种新校准原理，接若分析DDM系统的控制器MCU、限幅放大器、激光驱动器、存储单元、DCP的原理与作用，然后给出软件的设计思路和实现方案，最后通过实验数据验证该方案的可行性。2、参量校准原理根据SFF-8472协议，光模块的供电电压等五个模拟参量有内部校准和外部校准两种方式，内部校准的参数固化在程序里面，虽然可以通过外部界面设置改变，但是不同型号激光器PD响应度不一样，内部校准就很不灵活。外部校准，克服了内部校准的缺点，但是，由于要测量SLOPE和offet两个参数，需人工手调，在批量生产的情况下，测量效率低下。而使用内外部校准相结合的校准方式可以克服上述的缺点
上传时间： 2022-06-26
上传用户：
