虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

Results

  • DN457宽输入电压范围同步降压稳压器

      The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This Results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.

    标签: 457 DN 同步降压

    上传时间: 2013-11-07

    上传用户:moerwang

  • 基于8098单片机的SPWM变频调速系统

      数字控制的交流调速系统所选用的微处理器、功率器件及产生PWM波的方法是影响交流调速系统性能好坏的直接因素。在介绍了正弦脉宽调制(SPWM)技术的基础上,设计了一种以8098单片机作为控制器,以智能功率模块IPM为开关器件的变频调速系统。通过软件编程,产生正弦脉冲宽度调制波形来控制绝缘栅双极晶体管的导通和关断,从而达到控制异步电动机转速的目的。实验结果表明,该系统可调频率调电压,稳定度高,调速范围宽,具有较强的实用价值   Abstract:   AC variable speed with digital control systems used microprocessors, power devices and generate PWM wave is the direct factors of affecting the performance AC speed regulation system. On the basis of introducing the sinusoidal pulse width modulation (SPWM) technology,this paper designed variable speed system which used 8098 as a controller, intelligent power module IPM as switching device. Through software programming, resulting in sinusoidal pulse width modulation waveform to control the insulated gate bipolar transistor turn on and off, so as to achieve the purpose of speed control of induction motors. Experimental Results show that the system can adjust frequency modulation voltage, high stability, wide speed range, has a strong practical value.  

    标签: 8098 SPWM 单片机 变频调速系统

    上传时间: 2013-11-14

    上传用户:ynwbosss

  • 基于单片机系统的(24,16)循环码编码、译码方案

      在理论分析循环码编码和译码基本原理的基础上,提出了基于单片机系统的(24,16)循环码软件实现编码、译码的方案。仿真结果表明(24,16)循环码能有效地克服来自通讯信道的干扰,保证数据通信的可靠及系统的稳定,使误码率大幅度降低。本论文对(24,16)循环码的研究结果表明,可以有效地降低错误概率和提高系统的吞吐量,实现纠错仅需要在接收端增加有限的存储空间和计算复杂度,具有一定的实用价值。   Abstract:   Based on analyzing the theory of encoding and decoding of cyclic code, this paper showed the schemes of encoding and decoding of(24,16)cyclic code by the software and based on microcontroller. Simulation Results show that using (24,16) cyclic codes can effectively overcome the interference from communication channel, ensure the reliability and stability of data communication systems, and reduce the bit error rate greatly. The Results of this paper show that by using the (24,16) cyclic code, the error rate can be reduced and the system throughput can be improved. Meanwhile, the system only needs to enlarge limited storage space and computation the complexity at the receiving end to realize error correction. Thus the (24,16) cyclic code has a practical value.  

    标签: 24 16 单片机系统 循环码

    上传时间: 2013-11-09

    上传用户:gaoliangncepu

  • Atmel AT89C系列单片机电路板设计指南

    Designing Boards with Atmel AT89C51,AT89C52, AT89C1051, and AT89C2051 for Writing Flash at In-Circuit Test. Recent improvements in chips and testers have made it possible for the tester to begin taking over the role tradi-tionally assigned to the PROM program-mer. Instead of having a PROM pro- grammer write nonvolatile memories before assembling the board, the in-cir- cuit tester writes them during in-circuit testing operations. Many Teradyne Z18- series testers are now in use loading code into nonvolatile memories, micro- controllers and in-circuit programmable logic devices. The purpose of this note is to explain how the Z18 approaches the writing task for Atmel AT89C series IC’s, so that designers of boards using these chips can get the best Results.  

    标签: Atmel 89C AT 89

    上传时间: 2013-11-17

    上传用户:xiaozhiqban

  • 基于单片机的颜色自适应识别电路

      为解决电致变色器件的颜色变化受外界环境颜色控制的问题,设计了一种基于单片机的便携式颜色自适应识别电路。与传统颜色识别电路相比较,该电路利用数字式的颜色传感器来获取外界环境颜色,产生的数字颜色信号易于单片机进行处理。在电路中,下位机部分主要负责获取电致变色器件变色参数及控制电致变色器件的颜色变化;而上位机部分主要负责把下位机获取的电致变色器件变色参数进行电压到颜色的曲线拟合,并通过蓝牙通信把拟合曲线参数传递给下位机。结果表明,该电路能自动根据环境颜色提供-4~4 V范围步进为0.1 V的电压来驱动电致变色器件的颜色显示,与传统的颜色识别电路设计相比,识别的精度和速度都得到了明显改善。   Abstract:   In this paper, a portable adaptive circuit for color identification(PACCI) based on MCU was designed. Compared to the traditional color identification circuit, the PACCI adopts digital sensor to detect the color data from external environment and further generate digital color data, which can be processed easily by MCU. In PACCI, the slave is mainly responsible for detecting the color parameters of the corresponding elcreochromic device and further driving it. For the master, which is mainly responsible for the color curve fitting based on the parameters of the electrochromic device, and transmits the fitting parameters to the slave through the bluetooth device. The Results show that the PACCI can provide the basis voltage range from -4V to 4V automatically based on the colors of external environment with step as 0.1V to drive the corresponding electrochromic device. Compared to the traditional color recognition circuit, the recognition accuracy and speed of PACCI have been improved significantly.

    标签: 单片机 识别电路

    上传时间: 2013-11-09

    上传用户:franktu

  • 基于单片机的数字化B超键盘设计

    针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS,提出一种PS2键盘的设计方法。基于W78E052D单片机,采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路,电位器位置信息以键盘扫描码序列形式发送,正交编码器信号通过XC9536XL转换为单片机可接收的中断信号,软件接收到中断信息后等效处理成按键。结果表明,在满足开机可设置BIOS同时,又可实现超声特有功能,不需要专门设计驱动程序,接口简单,成本低。 Abstract:  Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot, this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller,designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter, potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU, software received interrupt information and equivalently treatmented as key. The Results show that the BIOS can be set to meet the boot, ultrasound specific functionality can be achieved at the same time, it does not require specially designed driver,the interface is simple and low cost.    

    标签: 单片机 B超 数字化 键盘设计

    上传时间: 2013-10-10

    上传用户:asdfasdfd

  • 基于PIC16LF874单片机的电容测量模块

    为提高电容测量精度,针对电容式传感器的工作原理设计了基于PIC16LF874单片机电容测量模块。简单阐述了电容测量电路的应用背景和国内外研究现状,介绍了美国Microchip公司PIC16LF874单片机的特性。电容式传感器输出的动态微弱电容信号通过PS021型电容数字转换器把模拟量数据转换成数字量数据,所测数据由PIC16LF874单片机应用程序进行处理、显示和保存。实验结果表明,固定电容标称值为10~20 pF 的测量值相对误差在1%以内,同时也可知被测电容容值越大,测量值和标称值相对误差越小。 Abstract:  To improve the accuracy of capacitance measurement,aimed at the principle of work of mercury capacitance acceleration transducer,the design of micro capacitance measurement circuit is based on the key PIC16LF874 chip. Briefly discusses the application of the capacitance measuring circuit for the background and status of foreign researchers,focusing on the United States PIC16LF874 microcontroller features. Capacitive sensor outputed signal through the dynamics of weak PS021-chip capacitors (capacitancedigital converter) to convert analog data into digital data,the measured data from the PIC16LF874 microcontroller application process, display and preservation. Experimental Results show that the fixed capacitor 10pF ~ 20pF nominal value of the measured value of relative error is within 1%,but also it canbe seen the value of the measured capacitance larger,measuring value and the nominal value of relative error smaller.

    标签: PIC 874 16 LF

    上传时间: 2013-10-29

    上传用户:wojiaohs

  • 基于ARM单片机的自动测高测距小车

    生活中许多目标的高度和水平距离需要进行测量。目前主要的测量方法,仍以传统的皮尺丈量为主,测量效率不高,有时还很不方便,没有技术成熟的数字式测高测距产品。以基本的数学方法为理论依据,利用遥控小车做为载体,采用角度传感器测量角度、霍尔传感器测量水平距离等,通过单片机LM3S615进行数据计算,实现了对待测目标物体的高度、水平距离等数据的快速、精确和数字式的测量,高度测量精度可达99.06%,水平测量精度则可达98.06%。 Abstract:  In our lives, the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods, and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory, this paper designed and manufactured a portable, digital and remote controlled measuring mobile small vehicle, which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple, the measuring Results are more accurate and the measuring efficiency is higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.

    标签: ARM 单片机 自动

    上传时间: 2013-10-30

    上传用户:jackandlee

  • 基于凌阳单片机的步进电机加减速的控制方法

    提出一种基于凌阳单片机的步进电机加减速的控制方法。采用凌阳科技推出的16位结构工控单片机SPMC75F2413A为控制器,由Allegro公司生产的两相步进电机专用驱动器件SLA7042M构成步进电机的驱动电路,在传统的3段直线加减速控制算法基础上增加至7段S形曲线加减速过程,控制步进电机的启动和停止。实验结果表明,该控制方法克服了直线加减速中不连续、易造成系统冲击的问题,整个系统实现柔性控制,电机启动、停止连续性能提高30%。 Abstract:  The method of controlled stepping motor is referred based on SPMC75F2413A MCU, which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental Results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control, and the performance of motor start or stop continuity is increased 30%

    标签: 凌阳单片机 步进电机 控制方法

    上传时间: 2013-12-08

    上传用户:jiangfire

  • 基于ATmega8的双轴太阳跟踪器设计

    为提高太阳能的利用率,以ATmega8单片机为控制核心,设计了一套光电跟踪与视日运动轨迹跟踪互补控制的双轴太阳跟踪器。该跟踪器在晴天时,利用光敏电阻采集光强判断太阳位置,控制步进电机实现光电跟踪;在阴天时,采集时钟器件PCF8583的时间信息,计算当前太阳位置来实现视日运动轨迹跟踪。实验表明:该太阳跟踪器能在不同天气状况下对太阳进行较准确地跟踪,能量接收效率提高了30%,达到充分利用太阳能的目的。 Abstract:  To improve the utilization rate of solar energy,a kind of solar tracking controller which effectively combined the sun angle tracking and photo electric tracking based on ATmega8is designed.In the sunny days,the solar tracking con-troller determines the sun's position by using photosensitive resistances to collect light intensity and control stepper motors to achieve photo electric tracking,n cloudy days,it collects clock chip PCF8583time information to calculate the current position of the sun and achieve the sun angle tracking.Experimental Results show the solar tracking controller accurately tracks the sun in different weather conditions,improves received energy efficiency by30%and reaches the purpose of full use of solar energy.

    标签: ATmega8 跟踪器

    上传时间: 2013-10-15

    上传用户:urgdil