为了使音频信号分析仪小巧可靠，成本低廉，设计了以2片MSP430F1611单片机为核心的系统。该系统将音频信号送入八阶巴特沃兹低通滤波器，对信号进行限幅放大、衰减、电平位移、缓冲，并利用一单片机负责对前级处理后的模拟信号进行采样，将采集得到的音频信号进行4 096点基2的FFT计算，并对信号加窗函数提高分辨率，另一单片机负责对信号的分析及控制显示设备。此设计精确的测量了音频信号的功率谱、周期性、失真度指标，达到较高的频率分辨率，并能将测量结果通过红外遥控器显示在液晶屏上。 Abstract: o make the audio signal analyzer cheaper， smaller and more Reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
上传时间： 2013-12-11
上传用户：jasonheung
设计一种基于P89V51RD2的功率因数测量仪，采用光电隔离器和专用数码管驱动器。该测量仪是以增强型单片机P89V51RD2为核心，大大简化系统硬件设计。而软件部分采用模块化设计思想，采用中值滤波和小数补偿算法，实现功率因数的高精度测量。实验测试表明，该功率因数测量仪测量精度高，运行稳定可靠。 Abstract: A power－factor measurement instrument based on P89V51RD2is designed，which uses optical coupler and specific LED drive chip.The power factor measurement instrument uses P89V51RD2as a core of which greatly simplifies the system design.Furthermore，modularization software is developed in detail.The high precision power－factor measuring system is realized by the center value filter and fractional compensation algorithm.Experiments manifests that the power－ factor measurement instrument is high precision，steady and Reliable.
上传时间： 2014-12-27
上传用户：CHINA526
为解决传统可视倒车雷达视频字符叠加器结构复杂，可靠性差，成本高昂等问题，在可视倒车雷达设计中采用视频字符发生器芯片MAX7456。该芯片集成了所有用于产生用户定义OSD，并将其插入视频信号中所需的全部功能，仅需少量的外围阻容元件即可正常工作。给出了以MAX7456为核心的可视倒车雷达的软、硬件实现方案及设计实例。该方案具有电路结构简单、价格低廉、符合人体视觉习惯的特点。经实际装车测试，按该方案设计的可视倒车雷达视场清晰、提示字符醒目、工作可靠，可有效降低驾驶员倒车时的工作强度、减少倒车事故的发生。 Abstract: A new video and text generation chip，MAX7456，was used in the design of video parking sensor in order to simplify system structure，improve reliability and reduce cost. This chip included all the necessary functions to generate user-defined OSDs and to add them into the video signals. It could be put into work with addition of just a small number of resistances and capacitors. This paper provided software and hardware implementation solutions and design example based on the chip. The system had the characteristics of simplicity in circuit structure，lower cost，and comfort for the nature of human vision. Loading road test demonstrates high video and text display quality and Reliable performance，which makes the driver easy to see backward and reduces chance of accidents.
上传时间： 2013-12-10
上传用户：qiaoyue
Important Notice SUNPLUS INNOVATION TECHNOLOGY INC. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS INNOVATION TECHNOLOGY INC. is believed to be accurate and Reliable. However, SUNPLUS INNOVATION TECHNOLOGY INC.makes no warranty for any errors which may appear in this document. Contact SUNPLUS INNOVATION TECHNOLOGY INC.to obtain the latest version of device specifications before placing your order. No responsibility is assumed by SUNPLUS INNOVATION TECHNOLOGY INC. for any infringement of patent or other rights of third parties which may result from its use. In addition, SUNPLUSIT products are not authorized for use as critical components in life support systems or aviation systems, where a malfunction or failure of the product may reasonably be expected to result in significant injury to the user, without the express written approval of SunplusIT
标签： SUNPLUSIT Q-Writer 编程工具 使用说明书
上传时间： 2013-10-13
上传用户：brain kung
根据看门狗电路的原理，设计出简单适用、性能可靠的1TrL型看门狗电路以及价格低廉、性能可靠的微功耗CMOS型看门狗电路，同时还介绍了常用的uP监视器O型看门狗电路。关键词：看门狗电路；1TrL型；CMOS型Abstract：In accordance with the principle of WDT (Watch Dog Timer 1circuit，design a，IT．L type WTD circuit，it is a dimple an d applicable an d Reliable on performanceo Design a CMOS type WTD circuit，it is low prices and mini-power consumption。Also the article describes a common uP type WTD circuit。Key word：WDT circuit；TFL type；CMOS typ e
上传时间： 2013-11-05
上传用户：685
基于PIC单片机的脉冲电源:设计了一种金属凝固过程用脉冲电源。该电源采用PIC16F877作为主控芯片，实现对窄脉冲电流幅值的检测，以及时电流脉冲幅值根据模糊PID算法进行闲环控制。使用结果表明：该电源的输出脉冲波形良好，电流幅值稳定，满足合金材料凝固过程的工艺要求且运行稳定可靠。关键词：脉冲电源；PIC16F877单片机；模糊PID；闲环控制 Abstract：A kind of pulse power supply was designed which uses in the metal solidification process ．．I11is power supply used PIC16F877 to take the master control chip reali on to the narrow pulse electric current peak-to-peak value examination，carried on the closed-loop control to the electric current pulse peak-to-peak value basis fuzzy PID algorithm．The use result indicated ，this power supply output se profile is good，and the electric current peak-to-p~k value is stable，It satisfies the alloy material solidification process the technological requirement and movement stable Reliable，Key words：p se po wer supply；PIC16F877single-chip microcontroller；f r PID；closed-loop control
上传时间： 2013-10-27
上传用户：xcy122677
基于多点网络的水厂自动监控系统设计Design of MPI Based Automatic Monitoring and Control System in Water Works刘 美 俊(湖南工程学院，湘潭411101)摘要针对水厂工作水泵多、现场离控制站距离远的特点，提出了一种基于MPI多点网络的自动监控系统的设计方法，分析了系统的工作原理，介绍了系统中数据的采集与处理、主站与从站的通信原理以及系统软件的设计。由于这种系统的主、从站PLC之间采用MPI网络通信，具有运行可靠、性能价格比高的特点，所以适用于中小规模水厂的分布式监控场合。关键词多点网络主站从站监控系统Abstract Ina ccordancew ithth efe atuersof w aterw orks,i. e. ，manyp umpsin o perationa ndth ep umps， farfor mt hec ontrolst ation,th em ethodo fdesigninga na utomati(〕monitoringa ndc ontorlsy stemb asedo nM PIis p resented.Th eo perationalpr incipleo fth esy stemi san alyzed,th ed atac olection,data processing; communication between master station and slave station as wel as design and system software are discussed. Because MPI network communicationis used among master station, slave stations and PLC, the system is Reliable and high cost-efective. It is， suitable for smal and mediumsized water works for distrbuted monitoring and control.Keywords MPI Masterst ation Slaves tation Monitoringa ndc ontorlsy stem 自来 水 厂 的自动控制系统一般分为两大部分，一对组态硬件要求较高，投资较大。相对而言，MPI网是水源地深水泵的工作控制，一是水厂区变频恒压供络速度可达187.5 M bps，通过一级中继器传输距离可水控制，两部分的实际距离通常都比较远。某厂水源达Ikm 。根据水厂的具体情况，确定以MPI方式组地有3台深井泵给水厂区的蓄水池供水。水厂区的成网络，主站PLC为S7-300系列的CPU3121FM，从任务是对水池的水进行消毒处理后，通过加压泵向管站为S7-200系列的CPU222。这样既满足了系统要路恒压供水。选用Siemens公司的S7系列可编程控求，又相对于Profibus网络节省了三分之一的成本，制器(PLC)和上位机组成实时数据采集和监控系统， 这种分布式监控系统具有较高的性能价格比。系统对深水泵进行远程控制，对供水泵采用变频器进行恒中PLC的物理层采用RS - 485接口，网络延伸选用压控制以保证整个水厂的电机设备安全、可靠地运带防雷保护的中继器，使系统的安全运行得到了保行。证。MPI网络的拓扑结构如图1所示。1 多点网络(NWI)监控系统的组成Sie me ns 公司S7系列PLC通常有MP」多点网络与Profibus现场总线网络两种组网方式。Profibus现场总线的应用目前较为普遍，通用性较好，它由Profibus一DP, Profibus一FMS, Profibus一PA组成。Profibus - DP型用于分散外设间的数据传输，传输速率为9.6kbps一12Mbps，主要用于现场控制器与分散1/0之间的通信，可满足交直流调速系统快速响应的时间要求，特别适合于加工自动化领域的应用;Profibus - FMS主要解决车间级通信问题，完成中等传输速度的循环或非循环数据交换任务，适用于纺织、楼宇自动化、可编程控制器、低压开关等;Profibus - PA型采用了OSI模型的物理层和数据链路层，适用于过程自动化的总线类型。
上传时间： 2013-10-09
上传用户：fac1003
Introduction to Xilinx Packaging Electronic packages are interconnectable housings for semiconductor devices. The major functions of the electronic packages are to provide electrical interconnections between the IC and the board and to efficiently remove heat generated by the device. Feature sizes are constantly shrinking, resulting in increased number of transistors being packed into the device. Today's submicron technology is also enabling large-scale functional integration and system-on-a-chip solutions. In order to keep pace with these new advancements in silicon technologies, semiconductor packages have also evolved to provide improved device functionality and performance. Feature size at the device level is driving package feature sizes down to the design rules of the early transistors. To meet these demands, electronic packages must be flexible to address high pin counts, reduced pitch and form factor requirements. At the same time,packages must be Reliable and cost effective.
上传时间： 2013-10-22
上传用户：ztj182002
为满足无线网络技术具有低功耗、节点体积小、网络容量大、网络传输可靠等技术要求，设计了一种以MSP430单片机和CC2420射频收发器组成的无线传感节点。通过分析其节点组成，提出了ZigBee技术中的几种网络拓扑形式，并研究了ZigBee路由算法。针对不同的传输要求形式选用不同的网络拓扑形式可以尽大可能地减少系统成本。同时针对不同网络选用正确的ZigBee路由算法有效地减少了网络能量消耗，提高了系统的可靠性。应用试验表明，采用ZigBee方式通信可以提高传输速率且覆盖范围大，与传统的有线通信方式相比可以节约40%左右的成本。 Abstract: To improve the proposed technical requirements such as low-ower， small nodes， large capacity and Reliable network transmission， wireless sensor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This paper provided network topology of ZigBee technology by analysing the component of the nodes and researched ZigBee routing algorithm. Aiming at different requirements of transmission mode to choose the different network topologies form can most likely reduce the system cost. And aiming at different network to choose the correct ZigBee routing algorithm can effectively reduced the network energy consumption and improved the reliability of the system. Results show that the communication which used ZigBee mode can improve the transmission rate， cover more area and reduce 40% cost compared with traditional wired communications mode.
上传时间： 2013-10-09
上传用户：robter
同步技术是跳频通信系统的关键技术之一，尤其是在快速跳频通信系统中，常规跳频通信通过同步字头携带相关码的方法来实现同步，但对于快跳频来说，由于是一跳或者多跳传输一个调制符号，难以携带相关码。对此引入双跳频图案方法，提出了一种适用于快速跳频通信系统的同步方案。采用短码携带同步信息，克服了快速跳频难以携带相关码的困难。分析了同步性能，仿真结果表明该方案同步时间短、虚警概率低、捕获概率高，同步性能可靠。 Abstract: Synchronization is one of the key techniques to frequency-hopping communication system， especially in the fast frequency hopping communication system. In conventional frequency hopping communication systems， synchronization can be achieved by synchronization-head which can be used to carry the synchronization information， but for the fast frequency hopping， Because modulation symbol is transmitted by per hop or multi-hop， it is difficult to carry the correlation code. For the limitation of fast frequency hopping in carrying correlation code， a fast frequency-hopping synchronization scheme with two hopping patterns is proposed. The synchronization information is carried by short code， which overcomes the difficulty of correlation code transmission in fast frequency-hopping. The performance of the scheme is analyzed， and simulation results show that the scheme has the advantages of shorter synchronization time， lower probability of false alarm， higher probability of capture and more Reliable of synchronization.
上传时间： 2013-11-23
上传用户：mpquest
