德州仪器(TI)通过多种不同的处理工艺提供了宽范围的运算放大器产品，其类型包括了高精度、微功耗、低电压、高电压、高速以及轨至轨。TI还开发了业界最大的低功耗及低电压运算放大器产品选集，其设计特性可满足宽范围的多种应用。为使您的选择流程更为轻松，我们提供了一个交互式的在线运算放大器参数搜索引擎——amplifier.ti.com/search，可供您链接至各种不同规格的运算放大器。设计考虑因素为某项应用选择最佳的运算放大器所要考虑的因素涉及到多个相关联的需求。为此，设计人员必须经常权衡彼此矛盾的尺寸、成本、性能等指标因素。即使是资历最老的工程师也可能会为此而苦恼，但您大可不必如此。紧记以下的几点，您将会发现选择范围将很快的缩小至可掌控的少数几个。电源电压(VS)——选择表中包括了低电压（最小值低于2.7V）及宽电压范围（最小值高于5V）的部分。其余运放的选择类型（例如精密），可通过快速查验供电范围栏来适当选择。当采用单电源供电时，应用可能需要具有轨至轨(Rail-to-Rail)性能，并考虑精度相关的参数。精度——主要与输入偏移电压(VOS)相关，并分别考虑随温度漂移、电源抑制比(PSRR)以及共模抑制比(CMRR)的变化。精密(precision)一般用于描述具有低输入偏置电压及低输入偏置电压温度漂移的运算放大器。微小信号需要高精度的运算放大器，例如热电偶及其它低电平的传感器。高增益或多级电路则有可能需求低偏置电压。
上传时间： 2013-11-25
上传用户：1966649934
Video cable driver amplifi er output stages traditionallyrequire a supply voltage of at least 6V in order to providethe required output swing. This requirement is usuallymet with 5V supplies by adding a boost regulator or asmall local negative rail, say via the popular LT®1983-3.Such additional circuitry is unnecessary in typical 1VP-Pvideo connections, such as HD component video, if thecable driver amplifi ers simply offer near Rail-to-Rail outputcapability when powered from 5V.
上传时间： 2013-11-16
上传用户：yanyangtian
This application note discusses a variety of approaches for interfacing analog signals to 5V powered systems. Synthesizing a "Rail-to-Rail" op amp and scaling techniques for A/D converters are covered. A voltage-to-frequency converter, applicable where high resolution is required, is also presented.
上传时间： 2013-10-12
上传用户：181992417
Precision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers Data Sheet AD8605/AD8606/AD8608The AD8605, AD8606, and AD86081 are single, dual, and quad Rail-to-Rail input and output, single-supply amplifiers. They feature very low offset voltage, low input voltage and current noise, and wide signal bandwidth. They use the Analog Devices, Inc. patented DigiTrim® trimming technique, which achieves
标签： 运算放大器
上传时间： 2022-02-02
上传用户：
The MAX5713/MAX5714/MAX5715 4-channel, low-power,8-/10-/12-bit, voltage-output digital-to-analog converters(DACs) include output buffers and an internal referencethat is selectable to be 2.048V, 2.500V, or 4.096V. TheMAX5713/MAX5714/MAX5715 accept a wide supplyvoltage range of 2.7V to 5.5V with extremely low power(3mW) consumption to accommodate most low-voltageapplications. A precision external reference input allowsRail-to-Rail operation and presents a 100kI (typ) load toan external reference.
上传时间： 2013-12-23
上传用户：ArmKing88
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上传时间： 2013-10-23
上传用户：wushengwu
Many system designers need an easy way to producea negative 3.3V power supply. In systems that alreadyhave a transformer, one option is to swap out the existingtransformer with one that has an additional secondarywinding. The problem with this solution is that manysystems now use transformers that are standard, offthe-shelf components, and most designers want toavoid replacing a standard, qualifi ed transformer with acustom version. An easier alternative is to produce thelow negative voltage rail by stepping down an existingnegative rail. For example, if the system already employsan off-the-shelf transformer with two secondary windingsto produce ±12V, and a –3.3V rail is needed, a negativebuck converter can produce the –3.3V output from the–12V rail.
上传时间： 2013-10-09
上传用户：Jerry_Chow
The LTC3546 is a dual output current mode buck regulatorwith fl exible output current partitioning. Beyondthe advantages normally associated with dual outputregulators (reduced size, cost, EMI and part count, withimproved effi ciency), the LTC3546’s outputs can bepartitioned for either 3A and 1A outputs, or two 2A outputs.This increases its application range and simplifi esmultiple supply rail designs. A confi gurable Burst Mode®clamp for each output sets the current transition levelbetween Burst Mode operation and forced continuousconduction mode to optimize effi ciency over the entireoutput range. An adjustable switching frequency up to4MHz and internal power MOSFET switches allow forsmall and compact footprints.
上传时间： 2013-11-04
上传用户：yxgi5
介绍一种基于CAN总线的牵引变电站自动化系统通讯规约的设计，CAN通讯规约采用标准帧，报文采用主动发送和发送查询两种处理形式。该设计在城市轻轨与地铁牵引变电站中的应用表明：可实现间隔层和通讯处理层的数据快速、可靠的交换，提高牵引变电站的安全性和稳定性 。 Abstract: This paper firstly presents a kind of design dealing with communicational protocol to the traction substation automation system based on CAN bus,and then comes up with the ideas that all frames of CAN communicational protocol should adopt the standard frame,and that messages be processed by two ways:sending initiatively and sending quiries.Subway and light rail application shows that the use of the CAN bus is possible to exchange data quickly and reliably between the layers of the middle and the communicational processing,hence to improve the safety and stability of traction substations.
上传时间： 2013-11-07
上传用户：bs2005
阐述了轨道交通列车定位技术。介绍了在轨道交通系统中列车定位技术的功能，国内外轨道交通中主要采用的列车定位方法，重点论述了几种主要定位技术，并从定位精度、闭塞制式、维护投资成本、抗干扰等方面进行分析比较。提出目前轨道交通定位技术应综合运用，取长补短，多种方法相互融合，才能满足轨道交通中对安全可靠性的要求。 Abstract: Rail train positioning technology is described. The paper introduces the funetions of the train positioning technology in the rail transit system， the main methods of train positioning do mestic and international rail， and focuses on several key methods， analyzes and compares from the positioning accuracy， block system, maintenance and investment cost， interference and so on， suggested that the current rail positioning technology should be integrated use of positioning method of meriging， learn from each other， to meet the reliability requirements of rail safety.
上传时间： 2013-11-25
上传用户：franktu
