The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上传时间： 2013-10-10
上传用户：adada
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
The design of battery-powered equipment can often bequite challenging. Since few ICs can operate directly fromthe end-of-life voltage from a 2-cell battery (about 1.8V),most systems require a DC/DCconverter. The systemdesigner often has a limited area in which to place the DC/DC converter; associated inductors and capacitors must be
上传时间： 2013-11-23
上传用户：wys0120
当前，太阳能光伏市场(包括光伏模块和逆变器)正以每年约30%的年累积速 度增长。太阳能逆变器的作用是将随太阳能辐射及光照变化的DC 电压转换成为 电网兼容的AC 输出；而对于广大电子工程师而言，太阳能逆变器是一个值得高 度关注的技术领域。因此下文将介绍太阳能逆变器设计所需注意的技术要点、挑 战以及相应的解决方法。 基本设计标准 基于太阳能逆变器的专用性以及保持设计的高效率，它需要持续监视太阳能 电池板阵列的电压和电流，从而了解太阳能电池板阵列的瞬时输出功率。它还需 要一个电流控制的反馈环，用于确保太阳能电池板阵列工作在最大输出功率点， 以应付多变的高输入。目前，太阳能逆变器已有多种拓扑结构，最常见的是用于 单相的半桥、全桥和Heric(Sunways 专利)逆变器，以及用于三相的六脉冲桥和 中点钳位（NPC）逆变器；图1 所示是这些逆变器的拓扑图(Microsemi 图源)。 同时，设计还需遵从安全规范，并在电网发生故障的时候可以快速断开与电网的 连接。因此，太阳能逆变器的基本设计标准包括额定电压、容量、效率、电池能 效、输出AC 电源质量、最大功率点跟踪（MPPT）效能、通信特性和安全性
标签： 太阳能逆变器
上传时间： 2014-12-24
上传用户：三人用菜
为解决直流逆变交流的问题，有效地利用能源，让电源输出最大功率，设计了高性能的基于IR2101最大功率跟踪逆变器，并以SPMC75F2413A单片机作为主控制器。高电压、高速功率的MOSFET或IGBT驱动器IR2101采用高度集成的电平转换技术，同时上管采用外部自举电容上电，能够稳定高效地驱动MOS管。该逆变器可以实现DC/AC的转换，最大功率点的跟踪等功能。实际测试结果表明，该逆变器系统具有跟踪能力强，稳定性高，反应灵敏等特点，该逆变器不仅可应用于普通的电源逆变系统，而且可应用于光伏并网发电的逆变系统，具有广泛的市场前景。 Abstract: To solve the problem of DC-AC inverter， and to utilize solar energy more efficiently， the design of maximum power point tracking inverter based on IR2101 was achieved with a high-performance， which can make the system output power maximum. SPMC75F2413A was adopted as main controller. IR2101 is a high voltage， high speed power MOSFET and IGBT driver. It adopted highly integrated voltage level transforming technology， and an external bootstrap capacitor was used， which could drive MOS tube efficiently and stably. Many functions are achieved in the system， such as DC/AC conversion， maximun power point tracking， etc. The actual test result shows that the inverter system has characteristics of strong tracking ability， high stability and reacting quickly. The design can not only be used in ordinary power inverter system， but also be used in photovoltaic power inverter system. The design has certain marketing prospects
上传时间： 2013-11-17
上传用户：lliuhhui
锁定放大是微弱信号检测的重要手段。基于相关检测理论，利用开关电容的开关实现锁定放大器中乘法器的功能，提出开关电容和积分器相结合以实现相关检测的方法，并设计出一种锁定放大器。该锁定放大器将微弱信号转化为与之相关的方波，通过后续电路得到正比于被测信号的直流电平，为后续采集处理提供方便。测量数据表明锁定放大器前级可将10-6 A的电流转换为10-1 V的电压，后级通过带通滤波器级联可将信号放大1×105倍。该方法在降低噪声的同时，可对微弱信号进行放大，线性度较高、稳定性较好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上传时间： 2013-11-29
上传用户：黑漆漆
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
XRP7714是一款四输出脉宽调制（PWM）分级降压（step down）DC-DC控制器，并具有内置LDO提供待机电源。该器件在单个IC上为电池供电的产品提供了整套的电源管理方案，并且通过内含的I2C串行接口进行整体的编程配置。XRP7714器件的每一路输出电压的编程范围是0.9V～5.1V，此范围内无需外部分压器。可编程DPWM开关频率的范围从300kHz到1.5MHz，使用户能够在效率和元件大小之间取得最优方案。为了让用户能够在设计的多路电源XRP7714系统能够取得最优的方案，下文将详细的介绍影响XRP7714系统效率的参数设置以及外围器件的选型。
上传时间： 2013-10-31
上传用户：chendawei
•用于对SIMATICS7-400的供电•用于将AC或DC网络电压转换为所需的5V DC和24VDC工作电压•输出电流为4A，10A和20A
上传时间： 2014-04-30
上传用户：1037540470
简介采用模数转换器(ADC)的现代电子系统要求更低功耗和更高性能。本文描述了采用线性电源和开关电源之间的差异，并论证了将高效DC-DC转换器和高性能模数转换器组合使用，可以显著降低系统功耗，同时不降低模数转换器的性能。
上传时间： 2013-10-27
上传用户：哈哈hah
