R7732_7733_7735是Richpower公司推出的高效AC TO DC 电源PWM控制芯片,最大功率可以做到75W;如有需求请联系我电话：021-54262182EXT 114 (Eric) QQ ：1187337351
上传时间： 2013-11-20
上传用户：xz85592677
长电c2383 TO-92L
上传时间： 2013-11-09
上传用户：wvbxj
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
Nuvoton NuMicro ICP Programmer 用户指南
标签： Programmer Nuvoton NuMicro ICP
上传时间： 2013-10-27
上传用户：longlong12345678
毕业设计 USB TO Gigabit LAN 网卡 随着网络技术飞速发展，多媒体的应用越来越多，人们对网络的要求也越来越高，为了适应市场的需求，网卡出现了。它以其结构简单、成本低廉、兼容性强等诸多的优越性得到了广泛的应用。由于网络的应用越来越广泛，网卡的应用也越来越多、功能越来越强大。开始时由于技术方面的限制，网卡只有10Mbps的吞吐量，由于网络技术的发展，100Mbps吞吐量的网卡开始在市场上得到广泛的应用。而现在1000Mbps吞吐量的网卡的出现又给网络的传输带来了新的活力。 论文中主要阐述了基于以太网的USB TO Gigabit LAN网卡的设计与制作。论文首先对以太网进行了介绍，紧接着讲了网卡的基本知识。随后又对USB TO Gigabit LAN网卡的电路设计和制作进行了详细的描述。论文还包括了USB TO Gigabit LAN网卡的调试等内容。
上传时间： 2014-12-02
上传用户：wab1981
详细介绍了TLC1549系列模数转换器的特点及工作原理，然后根据TLC1549的工作时序和A/D转换原理针对实际问题编写了详细的汇编语言程序。 Abstract: A basic principle and characteristic of TLC1549 analog-to-digital converter are introduced? detailedly in this article.Through engineering-oriented illustration,a microcomputer programmer base on basic principle and time sequence of TLC1549 is writted.
上传时间： 2014-07-16
上传用户：blans
PICkit™ 2 Microcontroller Programmer USER’S GUIDE This chapter contains general information that will be useful to know before using thePICkit™ 2 Microcontroller Programmer. Items discussed in this chapter include:• Document Layout• Conventions Used in this Guide• Warranty Registration• Recommended Reading• The Microchip Web Site• Development Systems Customer Change Notification Service• Customer Support• Document Revision History
标签： Microcontrolle PICkit 8482
上传时间： 2013-11-05
上传用户：妄想演绎师
1.The C Programming Language is a powerful, flexible andpotentially portable high-level programming language. 2.The C language may be used successfully to create a programfor an 8-bit MCU, but to produce the most efficient machinecode, the programmer must carefully construct the C Languageprogram.3.The programmer must not only create an efficient high leveldesign, but also pay attention to the detailed implementation.
上传时间： 2013-12-27
上传用户：huanglang
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
标签： MULTICHANNEL 5.5 TO RS
上传时间： 2013-10-19
上传用户：ddddddd
