基于FPGA设计的相关论文资料大全 84篇用FPGA实现FFT的研究 刘朝晖 韩月秋 摘 要 目的 针对高速数字信号处理的要求，给出了用现场可编程门阵列(FPGA)实现的 快速傅里叶变换(FFT)方案.方法 算法为按时间抽取的基4算法，采用递归结构的块浮点运 算方案，蝶算过程只扩展两个符号位以适应雷达信号处理的特点，乘法器由阵列乘法器实 现.结果 采用流水方式保证系统的速度，使取数据、计算旋转因子、复乘、DFT等操作协 调一致，在计算、通信和存储间取得平衡，避免了瓶颈的出现.结论 实验表明，用FPGA 实现高速数字信号处理的算法是一个可行的方案. 关键词 离散傅里叶变换； 快速傅里叶变换； 块浮点运算； 可编程门阵列 分类号 TP39； TN957.511 Implementation of FFT with FPGA Technology Liu Zhaohui Han Yueqiu (Department of Electronics Engineering, Beijing Institute of Technology, Beijing 100081) Abstract Aim To propose a scheme for implementing FFT with FPGA in accor-dance with the requirement for high speed digital signal PROCESSING. Methods The structure of FPGA and requirement of system were considered in the experiment, radix-4 algorithm of DIT and recursive structure were adopted. The group float point arithmetic operation was used in the butterfly and the array multiplier was used to realize multiplication. Results The pipeline pattern was used to ensure the system speed, it made fetching data, calculating twiddle factor, complex multiplication and D
标签： fpga
上传时间： 2022-03-23
上传用户：
设计了农业温湿度智能控制系统,该系统采用DHT11温湿度传感器作为温湿度采集模块,单片机选用AT89C52代替并调用Virtual terminal模拟串口通信,LCD1604液晶显示器实时显示温湿度,实现了温湿度的测量、显示,可自动控制加热、降温、加湿、通风,实现温湿度控制以及超限报警处理,并利用Proteus与Keil进行实际电路的仿真。试验表明,该系统实现了可靠的温湿度监控。We described the design of an intelligent control system of agriculture temperature and humidity.The system uses DHT11 temperature and humidity sensor as the temperature and humidity acquisition module.The SCM adopts AT89C52 to replace and call the virtual terminal for simulating serial communication.LCD1604 displays temperature and humidity in real time,which implements the measurement and display of temperature and humidity.The system is able to automatically control heating,cooling,humidification and ventilation,to achieve temperature and humidity control and over-limit alarm PROCESSING.The system also uses Proteus and Keil for actual circuit simulation.The experiment shows that the system is capable of reliable temperature and humidity monitoring.
上传时间： 2022-03-26
上传用户：aben
本系统采用电动机电枢供电回路串接采样电阻的方式来实现对小型直流有刷电动机的转速测量。该系统主要由二阶低通滤波电路,小信号放大电路、单片机测量显示电路、开关稳压电源电路等组成。同时自制电机测速装置,用高频磁环作为载体,用线圈绕制磁环,利用电磁感应原理检测电机运行时的漏磁,将变化的磁场信号转化为磁环上的感应电流。用信号处理单元电路将微弱电信号转化为脉冲信号,送由单片机检测,从而达到准确测量电机的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal PROCESSING unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
标签： 直流电动机
上传时间： 2022-03-26
上传用户：
随着光伏发电系统快速发展,以及电动汽车充电桩的普及,传统的剩余电流保护器无法满足实际需求。介绍了一款B型剩余电流保护器,采用磁调制剩余电流互感器和零序电流互感器采集剩余电流。根据GB/T 22794—2017标准要求,可识别1 kHz及以下的正弦交流、带和不带直流分量的脉动直流、平滑直流等剩余电流信号。经信号调理电路将电压信号送到单片机进行采集和判断。通过试验测试,该样机在测试精度和速度上均符合国家标准的相关要求。The rapid development of photovoltaic power generation systems and the popularity of electric vehicle charging piles make the traditional residual current protective devices unable to meet the actual demand.This paper proposed a type B residual current protective device,which uses the magnetically modulated residual current transformer and the zero sequence current transformer to acquire the residual current.According to the requirements of GB/T 22794—2017,the type B residual current protective device can detect sinusoidal AC residual current of 1kHz and below 1kHz,pulsating DC residual current with and without DC component,smooth DC residual current and so on.The signal PROCESSING circuit sends the voltage signal to the MCU for acquisition and judgment.Through experimental tests,the device meets the relevant requirements of national standards in terms of test accuracy and speed.
标签： 电流保护器
上传时间： 2022-03-27
上传用户：
温度控制如今已成为当代社会研究的热点之一,而温度检测在现代设备参数检测中也是一项极其重要的技术,应用十分广泛。与传统的测温方法相比,红外测温方法具有时间短、精度高、使用简单方便等优点。本文以环境温度为被测对象,设计了以STC89C52单片机为控制中心的红外测温装置,能够实现对目标温度的实时采集、处理、显示和报警等功能。本设计主要是由STC89C52单片机、红外测温传感器、LCD1602液晶显示器、按键和蜂鸣器等部分组成,采用非接触的方式对目标温度进行实时检测。Temperature control has become one of the hotspots in contemporary social research,and temperature detection is an extremely important technology in modern equipment parameter detection.Compared with traditional method,the infrared temperature measuring method has advantages of short time,high precision and convenient operation,etc.This paper consider environment temperature as research objects and designs an infrared temperature measuring device which employs the STC89C52singlechipas-control center,and it can realize timely collection,PROCESSING,display and alarm function of the target temperature.The design is mainly composed of STC89C52 singlechip,infrared temperature sensor,LCD1602monitor,keys and buzzer,etc.This design detects the target temperature by non-contact method.
上传时间： 2022-03-27
上传用户：jiabin
数字示波器功能强大,使用方便,但是价格相对昂贵。本文以Ti的MSP430F5529为主控器,以Altera公司的EP2C5T144C8 FPGA器件为逻辑控制部件设计数字示波器。模拟信号经程控放大、整形电路后形成方波信号送至FPGA测频,根据频率值选择采用片上及片外高速AD分段采样。FPGA控制片外AD采样并将数据输入到FIFO模块中缓存,由单片机进行频谱分析。测试表明:简易示波器可以实现自动选档、多采样率采样、高精度测频及频谱分析等功能。Digital oscilloscope is powerful and easy to use, but also expensive. The research group designed a low-cost digital oscilloscope, the chip of MSP430F5529 of TI is chosen as the main controller and the device of EP2C5T144C8 of Altera company is used as the logic control unit. Analog signal enter the programmable amplifier circuit, shaping circuit and other pre-PROCESSING circuit. The shaped rectangular wave signal is sent to FPGA for measure the frequency. According to the frequency value to select AD on-chip or off-chip high-speed AD for sampling. FPGA controls the off-chip AD sampling and buffers AD data by FIFO module. The single chip microcomputer receives the data, and do FFT for spectrum analysis. The test shows that the simple oscilloscope can realize automatic gain selection, sampling at different sampling rates, high precision frequency measurement and spectrum analysis.
上传时间： 2022-03-27
上传用户：
目的:自主研制一款超声手术刀电源控制系统,以减少能量的消耗,维持手术刀的正常温度。方法:对超声换能器在谐振附近的等效电路建立模型,并设计基于数字信号处理(DSP)的超声手术刀的硬件控制系统。结果:经对电源控制系统的电路和工作性能测试,生成的电流和电压的有效值等参数,能够及时调整电源的频率,并达到预期的功能指标,使超声手术刀工作在谐振状态。结论:以DSP为核心设计的超声手术刀电源控制系统,测试指标均能够达到预期的要求,能够使系统在谐振状态下工作。Objective: To independently develop a power control system of ultrasonic scalpel so as to reduce the energy consumption and maintain the normal temperature of ultrasonic scalpel. Methods: In this paper, the model of equivalent circuit of ultrasonic transducer nearby syntony was built up, and the hardware control system of ultrasonic scalpel based on digital signal PROCESSING(DSP) was designed. Results: Through testing the circuit and work performance of power control system, the series of parameters such as effective value and so on which were produced by this system could adjust frequency of power source in time and attain anticipative functional indicator, and it took the ultrasonic scalpel to work in syntonic situation. Conclusion: The tested indicators of power control system of ultrasonic scalpel based on the kernel design of DSP can attain anticipative requirement, and can take this system to work in syntonic situation.
上传时间： 2022-04-03
上传用户：bluedrops
Digital Signal PROCESSING in Python基于python的数字信号处理原版，对于dsp算法的快速原型验证非常有帮助。
上传时间： 2022-04-28
上传用户：
应用无迹卡尔曼滤波算法（UKF）进行锂电池的SOC估计,采用Thevenin二阶RC等效电路模型,对HPPC电池脉冲充放电实验数据进行Matlab处理,得到较为准确的模型.通过在Matlab中编写算法程序,对不同工况的估计值与实际值进行误差估算及对比分析,通过此算法进行SOC估计,得到该算法可有效降低系统误差并纠正SOC的初值偏差.The non trace Calman filter （UKF） is applied to the SOC estimation of lithium battery. The Thevenin two order RC equivalent circuit model is used to process the HPPC battery pulse charge discharge experimental data by Matlab PROCESSING, and a more accurate model is obtained. By writing algorithm program in Matlab, the error estimation and comparison analysis of the estimated value and actual value of different states are carried out, and the SOC estimation is carried out by this algorithm. The algorithm can effectively reduce the system error and correct the initial value deviation of the SOC.
标签： 卡尔曼滤波
上传时间： 2022-05-03
上传用户：默默
Allen的Think系列，讲述数字信号处理器（DSP）基本概念，用Python语言描述这些概念。可实际运行代码，更深的理解DSP。
上传时间： 2022-05-14
上传用户：
