华为pcb布线规范
上传时间： 2013-11-20
上传用户：han_zh
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2013-10-15
上传用户：busterman
随着现代电子科技的发展, 大规模集成电路迅速普及，芯片逐渐向高速化和集成化方向发展, 其体积越来越小，频率越来越高，电磁辐射随其频率的升高成平方倍增长，使得各种电子设备系统内外的电磁环境愈加复杂,对PCB 设计中的电磁兼容技术要求更高。PCB 电磁兼容设计是否合理直接影响设备的技术指标，影响整个设备的抗干扰性能，直接关系到整个系统的可靠性和稳定性。
上传时间： 2013-11-09
上传用户：540750247
pcb检查标准，即 pcb check list . 步骤非常之详细，按着步骤一步一步的检查就可以达到标准的。
上传时间： 2013-11-20
上传用户：my_cc
PCB布线对PCB的电磁兼容性影响很大，为了使PCB上的电路正常工作，应根据本文所述的约束条件来优化布线以及元器件/接头和某些IC所用去耦电路的布局PCB材料的选择通过合理选择PCB的材料和印刷线路的布线路径，可以做出对其它线路耦合低的传输线。当传输线导体间的距离d小于同其它相邻导体间的距离时，就能做到更低的耦合，或者更小的串扰（见《电子工程专辑》2000 年第1 期"应用指南"）。设计之前，可根据下列条件选择最经济的PCB形式：对EMC的要求·印制板的密集程度·组装与生产的能力·CAD 系统能力·设计成本·PCB的数量·电磁屏蔽的成本当采用非屏蔽外壳产品结构时，尤其要注意产品的整体成本/元器件封装/管脚样式、PCB形式、电磁场屏蔽、构造和组装），在许多情况下，选好合适的PCB形式可以不必在塑胶外壳里加入金属屏蔽盒。
上传时间： 2013-11-01
上传用户：dddddd
PCB专业术语词典
上传时间： 2014-05-15
上传用户：顶得柱
pcb Layout 设计从基础到实践多媒体教程
上传时间： 2013-11-19
上传用户：qw12
PCB板各个层的含义.pdf
标签： PCB
上传时间： 2013-10-24
上传用户：yangzhiwei
PCB电子书刊12期.pdf
上传时间： 2013-11-08
上传用户：小宝爱考拉
在Protel2004中进行PCB的完备的CAM输出。首先，我们可以输出的gerber文件， 操作如下：1：画好PCB后，在PCB 的文件环境中，左键点击File\Fabrication Outputs\Gerber Files,进入Gerber setup 界面
上传时间： 2013-10-14
上传用户：aeiouetla
