在汽车发动机起动时，若发动机起动后起动机不能及时断电，将会烧毁起动机或损坏飞轮齿环；若变速器不在空档位置起动，则起动机的瞬间动力将使汽车位移，还可能引起交通事故和人身安全。为此介绍一种利用NXP P89LPC901单片机控制的汽车起动保护控制器，通过检测汽车起动开关、变速箱档位、发动机转速，实现对汽车发动机起动过程检测和保护。起动保护控制器在发动机起动过程中通过采用逐个关闭打开负载系统，解决汽车发动机过程中因起动电流大而对汽车电源的冲击影响,延长了电瓶寿命。 Abstract: When the automotive engine is started, the engine start motor and flywheel gear may be damaged， even traffic accidents and personal safeties may be caused by wrong OPeration or other factors.In order to ensure the automotive engine can be started normally and safely,it is necessary that the protecting measures and methods are considered in the automotive electrical control system.This paper introduces a kind of the automotive engine starting protect controller based on NXP P89LPC901 MCU.The controller can protect the engine starting process by detecting the starter key switch,transmission stall and engine speed.Through the use of close and open load system,the controller can solve the impact on automotive power because of the high-current load in the process of the automobile engine starting, and extend battery life.
上传时间： 2013-10-15
上传用户：mikesering
C8051F020单片机通过SPI接口驱动四线电阻式触摸屏控制器TSC2046，利用中断方式驱动TSC2046设计软件。介绍了触摸屏的工作原理、TSC2046工作方式以及典型应用电路。 Abstract: The C8051F020 MCU is connected with the TSC2046 which is a 4-wire touch screen controller. The TSC2046 is controlled by interrupt mode, the? OPeration principle of touch screen is introduced. The OPeration mode of TSC2046 and typical application circuit are also discussed.
上传时间： 2014-12-27
上传用户：hwl453472107
提出了一种基于C8051F320的红外模拟枪战系统设计方案。介绍了红外模拟枪战系统的构成，给出了硬件选型、系统硬软件设计。利用红外抗对系统的工作原理，系统获得良好效果。 Abstract: This paper presents the design of simulated gunfight system based on C8051F320.Introduces system structure,and puts forward hardware selection of infrared simulated gunfight system and system hardware and software designs.Using the OPeration principle of infrared antagonizing system,the system result is good.
上传时间： 2013-11-20
上传用户：南国时代
介绍了MPC555与CS8900A扩展以太网的硬件设计图。以NUCLUES PLUS操作系统为基础，介绍了网卡软件驱动程序的编制，给出了以太网协议包嵌入NUCLEUS PLUS操作系统的实现方法。 Abstract: The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS OPeration system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real OPeration system are discussed.
上传时间： 2013-10-23
上传用户：xiehao13
介绍了电力操作电源与智能电池巡检系统的特点，给出了一种基于超低功耗单片机MSP430 F149针对中小型变电站自动化运行的专用设备的基本设计原理及实现方法，最后给出了详细硬件构成和软件实现。该系统能满足中小型变电站安全、可靠、自动运行的要求，并通过与上位机的串行通信实现变电站的远程管理和控制。 Abstract: The characters of the intelligent battery data logging system of the electric OPeration power are introduced.The basic design principle and the implemented methods of the special equipment which only designed for the middle or small transformer substation based on MSP430F149 are prescribed. Finally, the hardware block diagram and the software flow chart are also given. The function that the system finally needs to realize can basically meet with the middle or small transformer substation’s satisfy, reliably,and automatic running.And it can also realize the transformer substation long-distance management and control by serial communicating with the host computer.
上传时间： 2013-11-25
上传用户：黄华强
为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient OPeration. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
针对当前安检力学试验机所能完成的试验种类单一、自动化程度低等问题，提出一种以ATmega128单片机为核心控制器的安检力学试验机的设计。详细阐述了该安检力学试验机各个组成部分的设计原理和方案，并且给出了各部分的软件设计思想和操作流程。经过大量测试试验表明：设计的安检力学试验机可以完成多达十余种的力学安检试验，完全符合相关国家标准，并且具有数据采集精度高、传输速度快、操作安全简便等特点，实现了安检设备的多功能化、数字化和自动化。 Abstract: Currently， many mechanical security testing machines have only one function. The degree of automation of them is low. To solve those problems， a new kind of mechanical security testing machine， using ATmega128 micro-controller as its core controller， has been advanced. It describes the components of the machine. The principles and the scheme in the designing processes are presented in detail， and the software architecture and the OPeration processes of each part are given. After having done many testing， we have reached the following conclusions: the mechanical security testing machine presented can do over ten mechanical security tests complying with related national standards. It has high data acquisition accuracy and high transmission speed. The OPeration of the machine is simple and safe. In general， this machine is a multi-functional， highly automatic， digitalized security testing device.
上传时间： 2013-11-05
上传用户：a67818601
The LPC1700 Ethernet block contains a full featured 10 Mbps or 100 Mbps Ethernet MAC (Media Access Controller) designed to provide optimized performance through the use of DMA hardware acceleration. Features include a generous suite of control registers, half or full duplex OPeration, flow control, control frames, hardware acceleration for transmit retry, receive packet filtering and wake-up on LAN activity. Automatic frame transmission and reception with Scatter-Gather DMA off-loads many OPerations from the CPU.
上传时间： 2013-11-09
上传用户：geshaowei
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system OPeration is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW OPeration) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上传时间： 2013-11-13
上传用户：fredguo
