This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
标签： Pulsoximeter Single-Chip Des
上传时间： 2013-10-27
上传用户：黑漆漆
The HCS12X family is the successor to the HCS12family, with many additional features. One new feature isthe increased memory available to the CPU and themethods available to access it. This document focuses onthe improved memory map configuration.
上传时间： 2013-11-13
上传用户：王者A
The PCA9516 is a BiCMOS integrated circuit intended forapplication in I2C and SMBus systems.While retaining all the operating modes and features of the I2Csystem, it permits extension of the I2C-bus by buffering both the data(SDA) and the clock (SCL) lines, thus enabling five buses of 400 pF.The I2C-bus capacitance limit of 400 pF restricts the number ofdevices and bus length. Using the PCA9516 enables the systemdesigner to divide the bus into five segments off of a hub where anysegment to segment transition sees only one repeater delay.
上传时间： 2013-11-21
上传用户：q123321
The PCA9540B is a 1-of-2 bidirectional translating multiplexer, controlled via the I2C-bus.The SCL/SDA upstream pair fans out to two SCx/SDx downstream pairs, or channels.Only one SCx/SDx channel is selected at a time, determined by the contents of theprogrammable control register.
上传时间： 2014-12-28
上传用户：nshark
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The PCA9544A provides 4 interrupt inputs, one for each channeland one open drain interrupt output. When an interrupt is generated byany device, it will be detected by the PCA9544A and the interruptoutput will be driven LOW. The channel need not be active fordetection of the interrupt. A bit is also set in the control byte.Bits 4 – 7 of the control byte correspond to channels 0 – 3 of thePCA9544A, respectively. Therefore, if an interrupt is generated byany device connected to channel 2, the state of the interrupt inputs isloaded into the control register when a read is accomplished.Likewise, an interrupt on any device connected to channel 0 wouldcause bit 4 of the control register to be set on the read. The mastercan then address the PCA9544A and read the contents of thecontrol byte to determine which channel contains the devicegenerating the interrupt. The master can then reconfigure thePCA9544A to select this channel, and locate the device generatingthe interrupt and clear it. The interrupt clears when the deviceoriginating the interrupt clears.
标签： 4channel multiple 9544A 9544
上传时间： 2014-12-28
上传用户：潜水的三贡
The PCA9542A is a 1-of-2 bidirectional translating multiplexer, controlled via the I2C-bus.The SCL/SDA upstream pair fans out to two SCx/SDx downstream pairs, or channels.Only one SCx/SDx channel is selected at a time, determined by the contents of theprogrammable control register. Two interrupt inputs, INT0 and INT1, one for each of theSCx/SDx downstream pairs, are provided. One interrupt output, INT, which acts as anAND of the two interrupt inputs, is provided.
上传时间： 2013-12-07
上传用户：europa_lin
The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, or channels. Only oneSCx/SDx channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that channel.
上传时间： 2014-12-28
上传用户：270189020
The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
上传时间： 2013-10-13
上传用户：bakdesec
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上传时间： 2013-10-11
上传用户：dianxin61
