为了提高超高频RFID系统中阅读器在低信噪比的情况下仍具有较高的识别能力,提出一种基于FPGA系统结合软件无线电方法实现超高频RFID射频前端电路方案。超高频射频识别系统必须符合EPC Class 1generation 2标准,所设计的电路系统以Xilinx公司的XC6SLX16-2CSG324FPGA芯片为硬件基础,将数字基带调制解调和中频滤波电路在FPGA系统中设计实现,重点阐述了射频前端电路的设计结构、AD/DA转换电路,以及数字滤波器的设计。实验结果表明,所设计的超高频RFID阅读器简化了前端电路系统结构,提升了稳定性,增强了抗干扰能力。该电路系统在信噪比较低的情况下,能够较好地实现915MHz频率的射频接收和发送。In order to improve the reader UHF RFID system still has a higher ability to identify,in the case of low signal-to-noise ratio.The UHF RFID systems must comply with EPC Class 1 generation 2 standard.In this paper,the design of the circuit system based on Xilinx＇s XC6SLX16-2CSG324 FPGA chip,and presents UHF RFID RF front-end circuit with software radio based on FPGA system.Digital baseband modem and IF filter circuit is designed and implemented in the FPGA system,and focused on designing the structure of the RF front-end circuit,AD/DA conversion circuits,and digital filter.Experimental results show that the UHF RFID reader de...
标签： 915mhz 超高频 rfid 阅读 射频 前端 电路 设计
上传时间： 2022-04-17
上传用户：shjgzh
Vivado设计分为Project Mode和Non-project Mode两种模式，一般简单设计中，我们常用的是Project Mode。在本手册中，我们将以一个简单的实验案例，一步一步的完成Vivado的整个设计流程一、新建工程1、打开Vivado 2013.4开发工具，可通过桌面快捷方式或开始菜单中xilinx DesignTools-Vivado 2013.4下的Vivado 2013.4打开软件，开启后，软件如下所示：2、单击上述界面中Create New Project图标，弹出新建工程向导，点击Next.3、输入工程名称、选择工程存储路径，并勾选Create project subdirectory选项，为工程在指定存储路径下建立独立的文件夹。设置完成后，点击Next注意：工程名称和存储路径中不能出现中文和空格，建议工程名称以字母、数字、下划线来组成。4、选择RTL Project一项，并勾选Do not specifty sources at this time，勾选该选项是为了跳过在新建工程的过程中添加设计源文件。点击Next.IA5、根据使用的FPGA开发平台，选择对应的FPGA目标器件。（在本手册中，以xilinx官方开发板KC705为例，Nexys4开发板请选择Artix-7 XC7A100TCSG324-2的器件，即Family和Subfamily均为Artix-7，封装形式（Package）为cSG324，速度等级（Speed grade）为-1，温度等级（Temp Grade）为C）。点击Next6、确认相关信息与设计所用的的FPGA器件信息是否一致，一致请点击Finish，不一致，请返回上一步修改。二、设计文件输入1、如下图所示，点击Flow Navigator下的Project Manager->Add Sources或中间Sources中的对话框打开设计文件导入添加对话框。2、选择第二项Add or Create Design Sources，用来添加或新建Verilog或VHDL源文件，点击Next
标签： vivado
上传时间： 2022-05-28
上传用户：默默
关于Xilinx IS（14.2）简单使用方法介绍安装ISE软件基本上是一路点击鼠标就是，但必须安装注册表文件，可在网上查找，可能是一个生成注册表文件或注册表文件（license），功能仿真是在设计输入后进行；时序仿真是在逻辑综合后或布局布线后进行。（系统差不多占20GB硬盘）1创建工程文件（New Projiect）File New Projiect。如输入文件名：Two20ne.在上图点击Next键，弹出如下窗口，设置一些参数，如下图所示：创建资源文件（New Source）ProjectNew Source。如输入文件名：One2Two.选择模型，如Verilog Module，输入HDL语言，或输入原理图。或Project>Add Source，，增加已存在的资源文件（*v）。实例：二选一电路。点击Next键，弹出如下窗口，
上传时间： 2022-06-18
上传用户：shjgzh
安装软件到ST的网站上下载最新版本的STM32CubeMX 软件：编写这份文档的时候最新版本是V4.17.0 将下载后的压缩包解压，双击里面的SetupSTM32CubeMX-4.17.0.exe 文件来安装软件， 出现下图的界面的时候按Next 按钮继续：在下面的窗口中选择“ I accept the terms of this license agreement ”然后继续按Next 按钮。2下一个出现的窗口是选择软件安装的路径， 默认安装路径是C:\Program Files(x86)\STMicroelectronics\STM32Cube\STM32CubeMX ，可以根据实际需要选择别的路径，本次安装在D 盘相同的路径上。按Next 按钮后弹出一个确认窗口，按确定键确定。接着弹出下图的配置窗口，按原来默认的配置，按Next 键继续。3安装完后，按Next 键继续。按Done 键关闭下面的窗口，完成所有的安装。4安装固件包点击桌面上的STM32CubeMX 图标运行软件。先修改软件包的安装路径，点击help 菜单选“ Updater Settings”选项。软件包默认安装在C:/Users/XIN/STM32Cube/Repository/ 目录下，STM32Cube 软件包比较大可以点击Browse 按键修改安装的路径。修改完软件包的安装路径后开始安装 STM32Cube软件包，点击 help 菜单选 “Insta lnl ewsoftware and/or firmware packages ”选项。
标签： stm32cubemx
上传时间： 2022-06-19
上传用户：jason_vip1
In this presentation, we will look at what the Serial Peripheral Interface, otherwise known as the SPI, is. and how it is used to communicate data to and from the PICmicro microcontroller.SPl is frequently used when few 1/O lines are available, but communication between two or more devices must be fast and easy to implement.In this presentation, we will discuss the following topics: We will first cover an Overview of SPI This section of the tutorial will introduce you to SPI and its concepts.Next, we will examine the use of SPI on the PICmicro MCU.The details of how SPI is implemented on a PICmicro device will be examined.Then, a Code Walkthrough will be given.The walkthough will explore code for both an SPI Master and SPI Slave. The example will have the Master generate data for sending to the slave.Finally, there will be a few resources given at the end of the presentation. These resources will allow you to explore in more detail the SPI interface
标签： spi协议
上传时间： 2022-06-20
上传用户：
Introduction The Sil9135/Sil9135A HDMI Receiver with Enhanced Audio and Deep Color Outputs is a second-generation dual-input High Definition Multimedia Interface(HDMI)receiver. It is software-compatible with the Sil9133receiver, but adds audio support for DTS-HD and Dolby TrueHD. Digital televisions that can display 10-or 12-bit color depth can now provide the highest quality protected digital audio and video over a single cable. The Sil9135and Sil9135A devices, which are functionally identical, can receive Deep Color video up to 12-bit,1080p @60Hz. Backward compatibility with the DVI 1.0specification allows HDMI systems to connect to existing DVI 1.0 hosts, such as HD set-top boxes and PCs. Silicon Image HDMI receivers use the latest generation Transition Minimized Differential Signaling(TMDS) core technology that runs at 25-225 MHz.The chip comes pre-programmed with High-bandwidth?
上传时间： 2022-06-25
上传用户：
1.1首先安装J-Link驱动>开发软件\Setup_JLinkARM_V468，双击要安装的“Setup JLinkARMV468.exe"，>安装过程全选“next”直到安装成功，>将JLINK插接到电脑的USB口，即可在我的电脑\管理\设备管理器\通用串行总线控制器中看到一个J-Link driver。舵机是一种位置（角度）伺服的驱动器，适用于需要角度不断变化并可以保持的控制系统。舵机是一种俗称，其实是一种伺服马达。控制信号由接收机的通道进入信号调制芯片，获得直流偏置电压。内部有一个基准电路，产生周期为20ms，宽度为1.5ms的基准信号，将获得的直流偏置电压与电位器的电压比较，获得电压差输出。电压差的正负输出到电机驱动芯片决定电机的正反转。当电机转速一定时，通过级联减速齿轮带动电位器旋转，使得电压差为0，电机停止转动。
上传时间： 2022-07-05
上传用户：
PrefaceDuring the past years, there has been a quickly rising interest in radio access technologies for providingmobile as well as nomadic and fixed services for voice, video, and data. The difference indesign, implementation, and use between telecom and datacom technologies is also becoming moreblurred. One example is cellular technologies from the telecom world being used for broadband dataand wireless LAN from the datacom world being used for voice-over IP.Today, the most widespread radio access technology for mobile communication is digital cellular,with the number of users passing 5 billion by 2010, which is more than half of the world’s population.It has emerged from early deployments of an expensive voice service for a few car-borne users,to today’s widespread use of mobile-communication devices that provide a range of mobile servicesand often include camera, MP3 player, and PDA functions. With this widespread use and increasinginterest in mobile communication, a continuing evolution ahead is foreseen.This book describes LTE, developed in 3GPP (Third Generation Partnership Project) and providingtrue 4G broadband mobile access, starting from the first version in release 8 and through the continuingevolution to release 10, the latest version of LTE. Release 10, also known as LTE-Advanced,is of particular interest as it is the major technology approved by the ITU as fulfilling the IMTAdvancedrequirements. The description in this book is based on LTE release 10 and thus provides acomplete description of the LTE-Advanced radio access from the bottom up.Chapter 1 gives the background to LTE and its evolution, looking also at the different standardsbodies and organizations involved in the process of defining 4G. It also gives a discussion of the reasonsand driving forces behind the evolution.Chapters 2–6 provide a deeper insight into some of the technologies that are part of LTE and itsevolution. Because of its generic nature, these chapters can be used as a background not only for LTEas described in this book, but also for readers who want to understand the technology behind othersystems, such as WCDMA/HSPA, WiMAX, and CDMA2000.Chapters 7–17 constitute the main part of the book. As a start, an introductory technical overviewof LTE is given, where the most important technology components are introduced based onthe generic technologies described in previous chapters. The following chapters provide a detaileddescription of the protocol structure, the downlink and uplink transmission schemes, and the associatedmechanisms for scheduling, retransmission and interference handling. Broadcast operation andrelaying are also described. This is followed by a discussion of the spectrum flexibility and the associated
上传时间： 2022-07-08
上传用户：
第一步：安装DFP软件包（1）按照Keil uVision5，步骤略。我的keil版本如下：uVision V5.21.1.0Copyright(C)2016 ARM Ltd and ARM Germany GmbH. All rights reserved.（2）下载GD3210X的DFP软件包。下载地址：（3）安装DFP软件包。双击pack文件进行安装，如下图所示：点击next，将包文件复制到上面的路径位置。如下图：GigaDevice文件夹就是安装好的软件包。第二步：创建Keil工程（1）通常要新建3个文件夹。如下图所示：（2）打开keil5，新建project.将工程文件放到Mdk-Arm目录下面。弹出器件选择界面：在Device 下拉框，选择Software Packs，选择GD32F103RB点击OK
上传时间： 2022-07-23
上传用户：
VIP专区-嵌入式/单片机编程源码精选合集系列（104）资源包含以下内容：1. mips命令集详解.2. 数码相框原理图,ZXDP-010 (8302+720).3. CBM2090单片8BIT 16BIT共板原理图.4. 红外线遥控是目前使用最广泛的一种通信和遥控手段。由于红外线遥控装置具有体积小、功耗低、功能强、成本低等特点.5. 时间触发嵌入式系统设计模式 使用8051系列微控制器开发可靠应用.6. 关于555时基电路原理以及应用的介绍说明.7. 一个关于s3c2410_LCD_640*480的驱动程序.8. ipod——touch攻略.9. SDMMC 源码 SD、MMC卡的读写程序.10. 嵌入式试验开发平台简介.11. Mobile phone MMI design reference..12. 我写的stv2248 芯片的驱动程序.13. 应用于S60平台的示例程序.14. YAFFS (Yet Another Flash File System) is now in its second generation and provides a fast robust fil.15. 关于h264的演示 内容不错 希望大家喜欢..16. Michael Barr是Netrino公司的总裁兼创始人.17. 2006年软考的嵌入式系统设计师考试题及答案.18. S3C2440开发板原理图以及成品图片.是硬件开发工程师的好参考资料.19. 一个可以实现嵌入式视频监控系统的服务器软件。.20. 一个可以实现嵌入式视频监控系统的最新版客户端软件。.21. 东软嵌入式高级C培训(2007)).22. 最新的uffs,目前是1.1.2版本.23. NokiaSeries40Book1,介绍了40平台的手机开发.24. 数控编程开发事例,对数控机床的直线和圆户进行插补,.25. 用STR710控制串口及CC1100进行无线通信.26. 非常不错的单片机开发板原理图.27. s3c44b0bootloader分析.28. 以 DSpic30f4011为 SPI SLAVE的范例程式.29. 汉字与字符显示函数。对于任一主函数.30. 最详细最专业的MODBus协议介绍。 给MODBus总线开发的朋友们一些参考！.31. 本文较为详细的介绍了双CPU的C51系统设计中.32. c51的时钟芯片读写函数.33. 本书介绍了PCI局部总线的基本概念,功能,操作规则和使用方法.34. Intel公司的闪存转换层(Flash Translaion Layer)规范指导文件.35. h.261 player with running h.261,p24,h26 file.36. I2C接口协议.37. First of all we would like to thank God Almighty for giving us the strength and confidence in pursi.38. 2008年最新出版Silverlight及Blend学习电子书教程合集.39. 利用VB與VC程式整合開發實現影像物體分類辨識的PLC輸送帶系統.40. 凌阳公司机sunplus1002在这个芯片下.
标签： 光电子
上传时间： 2013-06-25
上传用户：eeworm
