Abstract: Designers who Must interface 1-Wire temperature sensors with Xilinx field-programmable gate arrays(FPGAs) can use this reference design to drive a DS28EA00 1-Wire slave device. The downloadable softwarementioned in this document can also be used as a starting point to connect other 1-Wire slave devices. The systemimplements a 1-Wire master connected to a UART and outputs temperature to a PC from the DS28EA00 temperaturesensor. In addition, high/low alarm outputs are displayed from the DS28EA00 PIO pins using LEDs.
标签： PicoBlaze Create Master Xilinx
上传时间： 2013-11-12
上传用户：大三三
Nios II 软件开发人员手册中的缓存和紧耦合存储器部分 Nios® II embedded processor cores can contain instruction and data caches. This chapter discusses cache-related issues that you need to consider to guarantee that your program executes correctly on the Nios II processor. Fortunately, most software based on the Nios II hardware abstraction layer (HAL) works correctly without any special accommodations for caches. However, some software Must manage the cache directly. For code that needs direct control over the cache, the Nios II architecture provides facilities to perform the following actions:
上传时间： 2013-10-25
上传用户：虫虫虫虫虫虫
Introduction to Xilinx Packaging Electronic packages are interconnectable housings for semiconductor devices. The major functions of the electronic packages are to provide electrical interconnections between the IC and the board and to efficiently remove heat generated by the device. Feature sizes are constantly shrinking, resulting in increased number of transistors being packed into the device. Today's submicron technology is also enabling large-scale functional integration and system-on-a-chip solutions. In order to keep pace with these new advancements in silicon technologies, semiconductor packages have also evolved to provide improved device functionality and performance. Feature size at the device level is driving package feature sizes down to the design rules of the early transistors. To meet these demands, electronic packages Must be flexible to address high pin counts, reduced pitch and form factor requirements. At the same time,packages Must be reliable and cost effective.
上传时间： 2013-11-21
上传用户：不懂夜的黑
Today’s digital systems combine a myriad of chips with different voltage configurations.Designers Must interface 2.5V processors with 3.3V memories—both RAM and ROM—as wellas 5V buses and multiple peripheral chips. Each chip has specific power supply needs. CPLDsare ideal for handling the multi-voltage interfacing, but do require forethought to ensure correctoperation.
上传时间： 2013-11-10
上传用户：yy_cn
Digital cameras have become increasingly popular over the last few years. Digital imagingtechnology has grown to new markets including cellular phones and PDA devices. With thediverse marketplace, a variety of imaging technology Must be available. Imaging technologyhas expanded to include both charge-coupled device (CCD) and CMOS image sensors.
标签： CoolRunner-II XAPP CPLD 390
上传时间： 2013-10-16
上传用户：18710733152
The Virtex-4 features, such as the programmable IDELAY and built-in FIFO support, simplifythe bridging of a high-speed, PCI-X core to large amounts of DDR-SDRAM memory. Onechallenge is meeting the PCI-X target initial latency specification. PCI-X Protocol Addendum tothe PCI Local Bus Specification Revision 2.0a ([Ref 6]) dictates that when a target signals adata transfer, "the target Must do so within 16 clocks of the assertion of FRAME#." PCItermination transactions, such as Split Response/Complete, are commonly used to meet thelatency specifications. This method adds complexity to the design, as well as additional systemlatency. Another solution is to increase the ratio of the memory frequency to the PCI-X busfrequency. However, this solution increases the required power and clock resource usage.
上传时间： 2013-11-24
上传用户：18707733937
如果用户现有的是 Protel99SE 。ProtelDXP，Protel2004 版本： 1 在powerpcb 软件的中打开 PCB 文件，选择导出 ASCII 文件（export ascii file） ，ascii file 的版本应该选择 3.5 及以下的版本。 2 a 在 Protel99SE 。ProtelDXP ， 选择 File->Import->在出现的对话框中,选择文件类型中的PADS Ascil Files (*.ASC)输入对应文件即可 1.powerpcb-->export ascii file--->import ascii file with protel99 se sp5(u Must install padsimportor that is an add-on for 99sesp5 which can downloan from protel company ). 2.powerpcb-->export ascii file-->import ascii file in orcad layout-->import max file(orcad pcb file)with protel 99 or 99se.
上传时间： 2013-10-16
上传用户：whymatalab
Abstract: The reality of modern, small form-factor ceramic capacitors is a good reminder to always readthe data sheet. This tutorial explains how ceramic capacitor type designations, such as X7R and Y5V,imply nothing about voltage coefficients. Engineers Must check the data to know, really know, how aspecific capacitor will perform under voltage.
上传时间： 2013-11-04
上传用户：梧桐
Tug of War(A tug of war is to be arranged at the local office picnic. For the tug of war, the picnickers Must be divided into two teams. Each person Must be on one team or the other the number of people on the two teams Must not differ by more than 1 the total weight of the people on each team should be as nearly equal as possible. The first line of input contains n the number of people at the picnic. n lines follow. The first line gives the weight of person 1 the second the weight of person 2 and so on. Each weight is an integer between 1 and 450. There are at most 100 people at the picnic. Your output will be a single line containing 2 numbers: the total weight of the people on one team, and the total weight of the people on the other team. If these numbers differ, give the lesser first. )
上传时间： 2014-01-07
上传用户：离殇
Filename: main.c * Description: A simple test program for the CRC implementations. * Notes: To test a different CRC standard, modify crc.h. * * * Copyright (c) 2000 by Michael Barr. This software is placed into * the public domain and may be used for any purpose. However, this * notice Must not be changed or removed and no warranty is either * expressed or implied by its publication or distribution.
标签： test implementations Description Filename
上传时间： 2015-02-02
上传用户：leehom61
