The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上传时间： 2013-10-24
上传用户：s蓝莓汁
c pgm to find redundant paths in a graph.Many fault-tolerant network algorithms rely on an underlying assumption that there are possibly distinct network paths between a source-destination pair. Given a directed graph as input, write a program that uses depth-first search to determine all such paths. Note that, these paths are not vertex-disjoint i.e., the vertices may repeat but they are all edge-disjoint i.e., no two paths have the same edges. The input is the adjacency matrix of a directed acyclic graph and a pair(s) of source and destination vertices and the output should be the number of such disjoint paths and the paths themselves on separate lines. In case of multiple paths the output should be in order of paths with minimum vertices first. In case of tie the vertex number should be taken in consideration for ordering.
标签： fault-tolerant algorithms redundant underlyin
上传时间： 2013-12-18
上传用户：jkhjkh1982
This book gives a comprehensive overview of the technologies for the advances of mobile radio access networks. The topics covered include linear transmitters, superconducting filters and cryogenic radio frequency (RF) front head, radio over fiber, software radio base stations, mobile terminal positioning, high speed downlink packet access (HSDPA), multiple antenna systems such as smart antennas and multiple input and multiple output (MIMO) systems, orthogonal frequency division multiplexing (OFDM) systems, IP-based radio access networks (RAN), autonomic networks, and ubiquitous networks.
标签： Advances Networks Access Mobile Radio in
上传时间： 2020-05-26
上传用户：shancjb
Employing multiple transmit and receive antennas, namely using multi-input multi-output (MIMO) systems, has proven to be a major breakthrough in providing reliable wireless communication links. Since their invention in the mid-1990s, transmit diversity, achieved through space-time coding, and spatial multiplexing schemes have been the focus of much research in the area of wireless communications.
标签： Communication Systems Coding MIMO for
上传时间： 2020-05-26
上传用户：shancjb
Use of multiple antennas at both ends of wireless links is the result of the natural progression of more than four decades of evolution of adaptive antenna technology. Recent advances have demonstrated that multiple- input-multiple-output (MIMO) wireless systems can achieve impressive increases in overall system performance.
标签： Technology System MIMO
上传时间： 2020-05-28
上传用户：shancjb
The family of recent wireless standards included the optional employment of Multiple-Input Multiple-Output(MIMO)techniques.This was motivatedby the observationaccordingto the classic Shannon–Hartley law that the achievable channel capacity increases logarithmically with the transmit power. In contrast, the MIMO capacity increases linearly with the number of transmit antennas, provided that the number of receive antennas is equal to the number of transmit antennas. With the further proviso that the total transmit power is increased in proportion to the number of transmit antennas, a linear capacity increase is achieved upon increasing the transmit power, which justifies the spectacular success of MIMO systems.
标签： Multi-Functional Systems MIMO
上传时间： 2020-05-31
上传用户：shancjb
Linear Technology’s high performance battery management ICsenable long battery life and run time, while providing precision charging control, constantstatus monitoring and stringent battery protection. Our proprietary design techniques seamlesslymanage multiple input sources while providing small solution footprints, faster charging and100% standalone operation. Battery and circuit protection features enable improved thermalperformance and high reliability operation.
上传时间： 2013-10-13
上传用户：yyq123456789
1) Write a function reverse(A) which takes a matrix A of arbitrary dimensions as input and returns a matrix B consisting of the columns of A in reverse order. Thus for example, if A = 1 2 3 then B = 3 2 1 4 5 6 6 5 4 7 8 9 9 8 7 Write a main program to call reverse(A) for the matrix A = magic(5). Print to the screen both A and reverse(A). 2) Write a program which accepts an input k from the keyboard, and which prints out the smallest fibonacci number that is at least as large as k. The program should also print out its position in the fibonacci sequence. Here is a sample of input and output: Enter k>0: 100 144 is the smallest fibonacci number greater than or equal to 100. It is the 12th fibonacci number.
标签： dimensions arbitrary function reverse
上传时间： 2016-04-16
上传用户：waitingfy
英文描述： 8-Bit Serial-Input/Parallel-Output Shift Register 中文描述： 8位Serial-Input/Parallel-Output移位寄存器
上传时间： 2013-04-24
上传用户：epson850
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
