提出一种基于凌阳单片机的步进电机加减速的控制方法。采用凌阳科技推出的16位结构工控单片机SPMC75F2413A为控制器，由Allegro公司生产的两相步进电机专用驱动器件SLA7042M构成步进电机的驱动电路，在传统的3段直线加减速控制算法基础上增加至7段S形曲线加减速过程，控制步进电机的启动和停止。实验结果表明，该控制方法克服了直线加减速中不连续、易造成系统冲击的问题，整个系统实现柔性控制，电机启动、停止连续性能提高30%。 Abstract: The method of controlled stepping Motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping Motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping Motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of Motor start or stop continuity is increased 30%
上传时间： 2013-12-08
上传用户：jiangfire
首先研究CAN总线和SAE J1939协议，提出一种基于MC9S12HZ256微控制器的总线式汽车数字仪表解决方案。详细介绍SAE J1939协议的报文帧格式及应用层协议中发动机相关参数的定义，以及步进电机及其驱动和车速信号的处理方法。该数字仪表系统硬件平台由微处理器和信号采集和信息处理及显示等模块组成。软件设计部分编程实现了对CAN总线和各传感器数据的读取、处理。该系统能够实时反映车辆工况。 Abstract: In this paper，CAN bus and SAE J1939protocol are researched，and a vehicle digital instrument solution based on MC9S12HZ256MCU is proposed.The message frame format and some engine-related parameters’definition in SAE J1939application layer protocol are introduced in detail.Stepper Motor and its driver，the methods of speed signal process-ing are also introduced.The hardware platform of vehicle digital instrument is composed by MCU，signal acquisition mod-ule，and signal processing and displaying module.Data receiving and processing from CAN bus and sensors are accom-plished by programming，and vehicle condition can be reflected in real-time.
上传时间： 2013-10-20
上传用户：huannan88
应用德国Micronas公司的CDC3207G微控制器开发了一款汽车仪表板系统。详细地介绍了该系统的硬件原理，以及步进电机，音频控制，LCD显示，LED指示灯和报警灯等几个模块的实现方法。应用μC/OS-II实时操作系统开发软件。着重介绍了启动代码的设计和任务的规划。 Abstract: A dashboard system is developed by using CDC3207G microcontroller made by Micronas.The hardware of the sys-tem and the realization of the step Motor module,audio module,LCD display and LED indicator and alarm module are ex-plained in detail.The μC/OS-II real-time operating system is used for the software development and the starting code design and the task planning is explained specifically.
上传时间： 2013-10-26
上传用户：x4587
介绍了采用ATmega48单片机实现三相无刷直流电机控制器的方法。利用Atmega48获得带死区的脉宽调制（PWM）、霍尔传感器的换相处理、正弦驱动信号的产生和电机转速的控制等功能。采用该方法的优点是所需的外围器件少，成本低。 Abstract: The method of 3-phase brushless DC Motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of Motor.Using this method，the needed external devices are few, the cost is low.
上传时间： 2013-12-09
上传用户：330402686
在汽车发动机起动时，若发动机起动后起动机不能及时断电，将会烧毁起动机或损坏飞轮齿环；若变速器不在空档位置起动，则起动机的瞬间动力将使汽车位移，还可能引起交通事故和人身安全。为此介绍一种利用NXP P89LPC901单片机控制的汽车起动保护控制器，通过检测汽车起动开关、变速箱档位、发动机转速，实现对汽车发动机起动过程检测和保护。起动保护控制器在发动机起动过程中通过采用逐个关闭打开负载系统，解决汽车发动机过程中因起动电流大而对汽车电源的冲击影响,延长了电瓶寿命。 Abstract: When the automotive engine is started, the engine start Motor and flywheel gear may be damaged， even traffic accidents and personal safeties may be caused by wrong operation or other factors.In order to ensure the automotive engine can be started normally and safely,it is necessary that the protecting measures and methods are considered in the automotive electrical control system.This paper introduces a kind of the automotive engine starting protect controller based on NXP P89LPC901 MCU.The controller can protect the engine starting process by detecting the starter key switch,transmission stall and engine speed.Through the use of close and open load system,the controller can solve the impact on automotive power because of the high-current load in the process of the automobile engine starting, and extend battery life.
上传时间： 2013-10-15
上传用户：mikesering
基于AT89C52单片机的步进电机控制系统设计 摘 要: 提出了一个由AT89C52单片机控制步进电机的实例。可以通过键盘输入相关数据, 并根据需要, 实时对步进电机工作方式进行设置, 具有实时性和交互性的特点。该系统可应用于步进电机控制的大多数场合。实践表明, 系统性能优于传统的步进电机控制器。 关键词: 单片机; 步进电动机; 直流固态继电器; 实时控制 ABSTRACT: A stepp ing Motor control system based on AT89C52 chip microcomputer was described.The data can be inputwith keyboard, and stepp ingMotorwas controlled by these data. According to the demand, users can set the workingmodel of stepp ingMotor in real2time. This system can be widely used in stepp ing Motor controlling. The p ractice showed that the performance of this system outdid the tradi-tional stepp ing Motor controller.
上传时间： 2013-11-22
上传用户：vodssv
基于单片机的步进电机开环控制系统:通过ATMEL89C51单片机对步进电机进行控制,主要介绍了步进电机控制器、驱动电路和LED显示电路的设计,实现了步进电机的开环控制。在步进电机控制器的设计中,重点阐述了脉冲产生电路以及对速度的控制。该系统具有成本低、控制方便的特点。关键词: 单片机; 步进电机; 开环控制 Abstract: The design using ATMEL89C51 single chip to control the step2Motor with its controller, driving circuit and LED disp lay circuit to realize step Motor open2loop controlwere introduced. For the controller in this design,the circuit to p roduce pulse and the speed controlwere expatiated emphatically. This system possesses features of lower cost, easier control.Key words: single ch ip; step2Motor; open2loop con trol
上传时间： 2013-10-13
上传用户：cicizoe
针对无位置传感器无刷直流电机的位置检测问题，本文应用单片机成功地实现了一种软件检测方法，并给出了实测波形加以验证。关键词： 无刷直流电机 无传感器 位置检测Abstract: As to the position-detecting problem of sensorless brushless DC Motor, a softwarerealization by microcomputer is proposed successfully in the paper. Experiment results are also presented to verify the method.Keywords: brushless DC Motor, sensorless, position detecting
上传时间： 2013-11-01
上传用户：aappkkee
该文介绍了开关磁阻电机的基本原理，设计了一种用80C196 单片机实现的开关磁阻电机驱动系统，并对该开关磁阻电机调速系统的性能进行了实验与测试，实验证明该系统运行可靠。开关磁阻电动机是磁阻电动机与电子开关驱动控制器组成的控制装置，又称开关磁阻电机驱动系统（Switched Reluctance Motor drive,简称SRD）。电机结构简单坚固，运行可靠，系统具有启动转矩高、启动电流低、调速范围宽、运行效率高，特别适用于频繁启停及正反转运行，使得SRD 成为交，直流电机驱动系统以及无刷直流电机驱动系统的强有力竞争者。目前，SRD 已用于多个领域，如：电动车驱动、家用电器、伺服与调速系统等许多领域。本文设计了一个以 80C196 单片机为控制核心的SRD 的控制系统，充分利用了SRD 电机控制方式灵活的特点，采用数字化控制系统对SR 电机进行控制，简化了硬件电路，提高了系统的可靠性。
上传时间： 2013-11-05
上传用户：18711024007
提出了一个由AT89C52单片机控制步进电机的实例。可以通过键盘输入相关数据, 并根据需要, 实时对步进电机工作方式进行设置, 具有实时性和交互性的特点。该系统可应用于步进电机控制的大多数场合。实践表明, 系统性能优于传统的步进电机控制器。关键词: 单片机; 步进电动机; 直流固态继电器; 实时控制Con trol System of Stepp ingMotor Ba sed on AT89C52 ChipM icrocomputerMENGWu2sheng, L ILiang (College of Automatization, Northwestern Polytechnical Unversity, Xipan 710072, China)ABSTRACT: A stepp ing Motor control system based on AT89C52 chip microcomputer was described.The data can be inputwith keyboard, and stepp ingMotorwas controlled by these data. According to the demand, users can set the workingmodel of stepp ingMotor in real2time. This system can be widely used in stepp ing Motor controlling. The p ractice showed that the performance of this system outdid the tradi tional stepp ing Motor controller.KEY WORDS: Chip microcomputer; Stepp ingMotor; DCSSR; Real2time control
标签： Control System ingMot Stepp
上传时间： 2013-11-19
上传用户：leesuper
