DC/DC 升压IC：The FP6291 is a current mode boost DC-DC converter. Its PWM circuitry with built-in 0.25 Ω power MOSFET make this regulator highly power efficient. The internal compensation network also minimizes as much as 6 external component counts. The non-inverting input of error amplifier connects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrush current. The FP6291 is available in the SOT23-6L package and provides space-saving PCB for the application fields.
上传时间： 2013-11-07
上传用户：3294322651
Traditionally, an Electronic Circuit Breaker (ECB) comprisesa MOSFET, a MOSFET controller and a current senseresistor. The LTC®4213 does away with the sense resistorby using the RDS(ON) of the external MOSFET. The resultis a simple, small solution that offers a signifi cant lowinsertion loss advantage at low operating load voltage.The LTC4213 features two circuit breaking responses tovarying overload conditions with three selectable tripthresholds and a high side drive for an external N-channelMOSFET switch.
上传时间： 2014-03-02
上传用户：lixinxiang
The LTC3546 is a dual output current mode buck regulatorwith fl exible output current partitioning. Beyondthe advantages normally associated with dual outputregulators (reduced size, cost, EMI and part count, withimproved effi ciency), the LTC3546’s outputs can bepartitioned for either 3A and 1A outputs, or two 2A outputs.This increases its application range and simplifi esmultiple supply rail designs. A confi gurable Burst Mode®clamp for each output sets the current transition levelbetween Burst Mode operation and forced continuousconduction mode to optimize effi ciency over the entireoutput range. An adjustable switching frequency up to4MHz and internal power MOSFET switches allow forsmall and compact footprints.
上传时间： 2013-11-04
上传用户：yxgi5
Handheld electronic devices play a key role in our everydaylives. Because dependability is paramount, handhelds arecarefully engineered with lightweight power sources forreliable use under normal conditions. But no amount ofcareful engineering can prevent the mistreatment theywill undergo at the hands of humans. For example, whathappens when a factory worker drops a bar code scanner,causing the battery to pop out? Such events areelectronically unpredictable, and important data storedin volatile memory would be lost without some form ofsafety net—namely a short-term power holdup systemthat stores suffi cient energy to supply standby power untilthe battery can be replaced or the data can be stored inpermanent memory.
上传时间： 2013-11-05
上传用户：coeus
In general, a Hot Swap controller provides two importantfunctions to boards that can be plugged and unpluggedfrom a live backplane:
上传时间： 2013-10-23
上传用户：行者Xin
随着消费者购买便携设备数量的增多，他们也被具有各种非标准连接器的诸多电源适配器所束缚。为了解决这一问题，微型USB接口成为电池充电和数据传输的标准。MAX14578AE/MAX14578E过压保护充电检测器和限流开关大大简化了微型USB端口的设计，从而使终端用户操作更加轻松
上传时间： 2013-10-09
上传用户：chukeey
What would happen if someone connected 24V to your12V circuits? If the power and ground lines were inadvertentlyreversed, would the circuits survive? Does yourapplication reside in a harsh environment, where the inputsupply can ring very high or even below ground? Evenif these events are unlikely, it only takes one to destroya circuit board.
上传时间： 2013-10-26
上传用户：jackandlee
本发明用于LED 光源的电源向以串联或并联型式连接的不同数量LED 提供功率。所述电源使用电流反馈来调节到LED 的功率并对电路和电路故障提供保护。
上传时间： 2013-11-04
上传用户：奇奇奔奔
功能简述：本控制器采用微控制器控制，其功能如下：1． 12V/24V 蓄电池自动识别2． 自动开关灯智能感知外界光线，天黑时延时自动开启路灯，天亮时自动关闭路灯3． 自动充放电（以12V 蓄电池为例）进入白天后太阳能电池板电压高于蓄电池电压时自动进入充电状态，充电至蓄电池电压高于14.4V 就进入涓流状态充电。而当天黑且蓄电池电压高于10.6V 就允许向LED 放电。4． 蓄电池保护（以12V 蓄电池为例）：当蓄电池电压低（低于10.6V）时，会自动关闭路灯，防止过放，以保护电池。当电池充满（14.4V）时，会停止其他充电状态，而进入涓流充充电状态，以防止过充。5． 采用PWM 调光技术对LED 路灯进行调光，可以和各种可调光恒流源匹配工作。6． 为了节能而调光，可以有各种节能调光模式，以实现不同程度的节能。
上传时间： 2013-11-07
上传用户：wyc199288
IC 特色 : ˙ 半谐振模式之 ZVS零电压切换 , 能有效降低切换损失 , 提高效率 , 并具展频功能 , 改善EMI . ˙ 轻 / 重载的 Duty Factor 皆在 CCM 与 DCM 边缘 , 是最能发挥次级 "同步整流" 效率的一种工作模式 . ˙ 空载时进入 Cycle Skipping ( Typical 0.3W ) , 有效达成环保规範 . ˙ 内建 "LEB前缘遮没" 功能 , 避免电流迴授失真 . ˙ 能随输入电压变化 , 自动补偿 OPP过功率保护点 . ˙ 精密的 OVP 过压保护点可自行设定 . ˙ 完整的保护功能 : OVP过压保护 , OCP过流保护 , OPP过载保护 , SWP线圈短路保护 , SCP输出短路保护 , OTP过温度保护 .
上传时间： 2014-12-24
上传用户：回电话#
