This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2014-01-24
上传用户：s363994250
PCI-E是一种高速传输总线形式。
上传时间： 2013-12-18
上传用户：宋桃子
PCI-1734快速安装使用手册PCI-1734快速安装使用手册PCI-1734快速安装使用手册PCI-1734快速安装使用手册PCI-1734快速安装使用手册PCI-1734快速安装使用手册PCI-1734快速安装使用手册
上传时间： 2013-10-22
上传用户：ssz1990
本文介绍一种基于PCI Express 总线的高速数据采集卡的设计方案及功能实现。给出系统的基本结构及单元组成，重点阐述系统硬件设计的关键技术和本地总线的控制逻辑，详细探讨了基于DriverWorks 的设备驱动程序的开发以及上层应用软件的设计。该系统通过实践验证，可用于卫星下行高速数据的接收并可适用于其他高速数据采集与处理系统。关键词：PCI Express 总线 PCIE PEX8311 DMA 板卡驱动 随着空间科学和空间电子学技术的飞速发展，空间科学实验的种类和数量以及科学实验所产生的数据量不断增加。为了使地面接收处理系统能够实时处理和显示科学图像数据，必须要设计出新的地面数据接收处理系统，实现大量高速数据的正确接收采集、处理以及存储。为了满足地面系统的要求，并为以后的计算机系统升级提供更广阔的空间，本系统拟采用第三代I/O 互连技术PCI Express（简称PCI-E）作为本数据采集卡的进机总线形式。本文通过对PCI-E 总线专用接口芯片PLX 公司的PEX8311 性能分析，特别是对突发读、写和DMA读操作的时序研究，设计出本地总线的可编程控制逻辑，并详细讨论了整个PCI-E 高速数据采集卡的硬件设计方案，以及WDM 驱动程序和上层应用程序的设计方法。
上传时间： 2013-10-28
上传用户：tianyi996
浏览所有的PCI设备
上传时间： 2015-01-03
上传用户：zsjinju
一个通过PCI卡向LED屏发送股票实时行情的系统
上传时间： 2015-01-04
上传用户：498732662
PCI接口的Verilog源代码
上传时间： 2013-12-28
上传用户：l254587896
pci驱动程序的源代码
上传时间： 2015-01-12
上传用户：ljmwh2000
PCI接口的PCMCIA转界卡的2000驱动，解决2000不支持存储卡问题
上传时间： 2014-01-17
上传用户：王楚楚
在dos下读写pci卡
上传时间： 2015-01-16
上传用户：windwolf2000
