介绍了以AVR单片机ATmega16为核心，采用前端信号调理电路、程控增益放大器以及波形显示LCD（GDM12864A）实现的一个简易示波器。并给出该系统设计的硬件和软件设计方案。 Abstract: Abstract:This paper introduces an easy digital storage oscilloscope based on the AVR MICROcontrolLER ATmega16,especially emphasizes on the software design and the hardware design which contains signal processing circuit,gain-programmed amplifier circuit and LCD’s interface circuit and so on.
上传时间： 2013-10-13
上传用户：ccccccc
应用德国Micronas公司的CDC3207G微控制器开发了一款汽车仪表板系统。详细地介绍了该系统的硬件原理，以及步进电机，音频控制，LCD显示，LED指示灯和报警灯等几个模块的实现方法。应用μC/OS-II实时操作系统开发软件。着重介绍了启动代码的设计和任务的规划。 Abstract: A dashboard system is developed by using CDC3207G MICROcontrolLER made by Micronas.The hardware of the sys-tem and the realization of the step motor module,audio module,LCD display and LED indicator and alarm module are ex-plained in detail.The μC/OS-II real-time operating system is used for the software development and the starting code design and the task planning is explained specifically.
上传时间： 2013-10-26
上传用户：x4587
气压是气象监测中的一个重要参数，提出了一种气压数据采集模块设计方案，该模块采用数字气压传感器MS5534B、MSP430单片机MSP430F2272和带实时时钟（RTC）64 KB铁电存储器。通过低功耗软件设计方法以微安级整体平均功耗实现了气压数据的采集和存储，适合电池供电的连续高精度气压采集应用。给出了模块的软硬件设计以及MS5534B的性能指标和使用经验。 Abstract: Air pressure is an important parameter in weather monitor.This paper futs forward a new design scheme of low power-air pressure data acquisition module.The module uses a digital output barometer sensor MS5534B,MSP430 MICROcontrolLER MSP430F2272 and integrated RTC 64KB FRAM,precision air pressure measurement and storage chip.Another point of this module is low power consumption, so it is well suited for battery powered air pressure data acquisition applications. At the same time,the software and hardware deign of module is presented,And the speciaties and use notices of MS5534B are given.
上传时间： 2014-12-27
上传用户：drink！
介绍了一种基于AT89S52微处理器、键控显示模式、多汉字显示的显示模块设计方法。对AT89S52的内部功能及使用高128字节RAM时的寻址方式进行说明。给出了四汉字显示模块的硬件电路原理图、主程序流程图以及中断显示流程图。 Abstract: The design method of display module base on the AT89S52 MICROcontrolLER,display mode controlled by keyboard and? showing several Chinese characterses are introduced in the paper.The internal function and the addressing mode for the high 128B RAM of the AT89S52 are explained.The basic circuit diagram,the main program flow chart and the display interrupt flow chart of four Chinese characterses display module are also given.
上传时间： 2014-01-23
上传用户：咔乐坞
针对众多低成本数据采集需求，采用带有片上USB控制器和D/A转换器的混合信号微处理器C8051F340，设计了一款可通过USB接口和LabVIEW图形用户界面实现与PC机联机的数据采集器，同时借助系统的SD卡存储独立实现现场长时间采集数据。该数据采集器成本低，结构简单，体积小，已成功用于工业现场。 Abstract: Aiming at the need of low cost data acquisition, a data acquisition device is designed based on C8051F340 which is a mixed-signal MICROcontrolLER and integrates USB controller and A/D controller on a chip.The data acquisition device which can combine with PC by USB interface and LabVIEW graphical user interface,can realize data acquisition. At the same time,it can be solely run a long time in virtue of SD card in field.The date aequisition device features low cost,simple structure and little sharp, and it has been used in industry field.
上传时间： 2014-05-31
上传用户：1109003457
为了解决磁放大器性能测试过程中，需要对其供给不同数值恒定电流的问题，设计了一种基于DAC7512和单片机的数控恒流源系统。该系统采用AT89C51作为主控器件，将计算机发送的电流控制字命令转换为D/A转换器控制字，通过模拟SPI通信接口，写D/A控制字到DAC7512，从而控制其输出相应数字电压值，经差动缩放电路、电压/电路变换电路和功率驱动电路，最后输出恒定电流。实验结果表明，恒流源输出电流调节范围为-45~+45 mA、精度为±0.1 mA，分辨率达0.024 4 mA，具有应用灵活，外围电路简单，可靠性高的特点。该数控直流恒流源也可为相关产品的测试系统研发提供参考。 Abstract: In order to solve the need to supply different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and MICROcontrolLER technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
上传时间： 2014-12-27
上传用户：invtnewer
以AVR单片机ATmega8和USB接口器件PDIUSBD12为核心，基于标准的USB1.1协议，设计一种通用USB接口模块，以满足嵌入式系统中对USB接口的需求。对模块的硬件电路或单片机固件程序的硬件接口层稍加修改即可用于其他各种微处理器。该模块可为各种嵌入式系统增加USB接口,实现与USB主机系统通信。 Abstract: Based on AVR MICROcontrolLER ATmega8 and USB interface chip PDIUSBD12, a general USB interface module is designed according to USB1.1 protocol for various requirements of embedded systems. Only with few modifications in circuit or hardware abstract layer of firmware, the module can be used on many types of microprocessors. All kinds of embedded systems can realize high speed and stable communication with USB host systems, owing to the facility of this module.
上传时间： 2014-01-08
上传用户：赵云兴
为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on MICROcontrolLER is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
在介绍基于MSP430单片机的指纹保险柜工作原理的基础上，从系统软件设计的角度出发，详细介绍了指纹保险柜软件的总体分析过程、程序结构的设计以及代码的编写，给出了按键管理流程和部分源代码。 Abstract: On basis of the operating principle of MSP430 MICROcontrolLER-based fingerprint safe,the general analyzing process,program designing and code compiling of the fingerprint safe software are introduced mainly,and the key-press flows chart and some codes according to the system software designing are put forward.
上传时间： 2014-12-27
上传用户：gaojiao1999
对于沥青混凝土摊铺机自动找平控制系统来说，数字式控制系统的研制是目前的一个方向。介绍了一种基于CAN总线的数字式自动找平控制系统。该系统以CAN总线作为通信方式，PWM控制信号通过C8051F040单片机内部PCA可编程计数器阵列产生，并具有结构简单、信号稳定、实时性强、易扩展的特点。通过硬件实现和系统运行达到了比较理想的控制效果，验证了系统的可行性。 Abstract: A digital auto-leveling control system based on CAN Bus is introduced.It uses CAN Bus as the method of communication and creates PWM signals by programmable counter array in C8051F040 MICROcontrolLER. The system is simple, stable, real-time and expansive.
上传时间： 2013-10-09
上传用户：ligi201200
