SAMSUNG’s S3C2440A is designed to provide hand-held devices and general applications with low-power, and high-performance microcontroller solution in small die size. To reduce total system cost, the S3C2440A includes the following components.
标签： applications hand-held low-power S3C2440A
上传时间： 2013-12-18
上传用户：zhenyushaw
SimpliciTI™ -1.0.3.exe for CC11xx and CC25xx SimpliciTI is a simple low-power RF network protocol aimed at small (<256) RF networks. Such networks typically contain battery operated devices which require long battery life, low data rate and low duty cycle and have a limited number of nodes talking directly to each other or through an access point or range extenders. Access point and range extenders are not required but provide extra functionality such as store and forward messages. With SimpliciTI the MCU resource requirements are minimal which results in the low system cost.
标签： SimpliciTI low-power network simple
上传时间： 2014-11-05
上传用户：rishian
SimpliciTI™ -1.0.4.exe for CC2430 SimpliciTI is a simple low-power RF network protocol aimed at small (<256) RF networks. Such networks typically contain battery operated devices which require long battery life, low data rate and low duty cycle and have a limited number of nodes talking directly to each other or through an access point or range extenders. Access point and range extenders are not required but provide extra functionality such as store and forward messages. With SimpliciTI the MCU resource requirements are minimal which results in the low system cost.
标签： SimpliciTI low-power protocol network
上传时间： 2016-05-21
上传用户：R50974
The MAX2691 low-noise amplifier (LNA) is designed forGPS L2 applications. Designed in Maxim’s advancedSiGe process, the device achieves high gain andlow noise figure while maximizing the input-referred 1dBcompression point and the 3rd-order intercept point. TheMAX2691 provides a high gain of 17.5dB and sub 1dBnoise figure.
标签： Amplifier Low-Noise 2691 Band
上传时间： 2014-12-04
上传用户：zaocan888
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
上传时间： 2013-10-21
上传用户：ljt101007
介绍了采用ATmega48单片机实现三相无刷直流电机控制器的方法。利用Atmega48获得带死区的脉宽调制（PWM）、霍尔传感器的换相处理、正弦驱动信号的产生和电机转速的控制等功能。采用该方法的优点是所需的外围器件少，成本低。 Abstract: The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
上传时间： 2013-12-09
上传用户：330402686
为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
The AT89C52 is a low-power, high-performance CMOS 8-bit microcomputer with 8Kbytes of Flash programmable and erasable read only memory (PEROM). The deviceis manufactured using Atmel’s high-density nonvolatile memory technology and iscompatible with the industry-standard 80C51 and 80C52 instruction set and pinout.The on-chip Flash allows the program memory to be reprogrammed in-system or by aconventional nonvolatile memory programmer. By combining a versatile 8-bit CPUwith Flash on a monolithic chip, the Atmel AT89C52 is a powerful microcomputerwhich provides a highly-flexible and cost-effective solution to many embedded controlapplications.
上传时间： 2013-11-10
上传用户：1427796291
As businesses and consumers expect more fromportable electronics, the FPGA industry has beencompelled to re-think how it serves these low-power,cost-sensitive markets. Application classes like
上传时间： 2013-11-10
上传用户：XLHrest
Abstract: This reference design provides design ideas for a cost-effective, low-power liquid-level measurement dataacquisition system (DAS) using a compensated silicon pressure sensor and a high-precision delta-sigma ADC. Thisdocument discusses how to select the compensated silicon pressure sensor, suggest system algorithms, and providenoise analyses. It also describes calibration ideas to improve system performance while also reducing complexity andcost.
上传时间： 2013-10-08
上传用户：sjy1991
