超声波传感器适用于对大幅的平面进行静止测距。普通的超声波传感器测距范围大概是 2cm~450cm，分辨率3mm（淘宝卖家说的，笔者测试环境没那么好，个人实测比较稳定的 距离10cm~2m 左右，超过此距离就经常有偶然不准确的情况发生了，当然不排除笔者技术 问题。） 测试对象是淘宝上面最便宜的SRF-04 超声波传感器，有四个脚：5v 电源脚（Vcc），触发控制端（Trig），接收端（Echo），地端（GND） 附:SRF 系列超声波传感器参数比较 模块工作原理： 采用IO 触发测距，给至少10us 的高电平信号； 模块自动发送8个40KHz 的方波，自动检测是否有信号返回； 有信号返回，通过IO 输出一高电平，高电平持续的时间就是超声波从发射到返回的时间．测试距离=(高电平时间*声速(340m/s))/2; 电路连接方法 Arduino 程序例子： constintTrigPin = 2; constintEchoPin = 3; floatcm; voidsetup() { Serial.begin(9600); pinMode(TrigPin, OUTPUT); pinMode(EchoPin, INPUT); } voidloop() { digitalWrite(TrigPin, LOW); //低高低电平发一个短时间脉冲去TrigPin delayMicroseconds(2); digitalWrite(TrigPin, HIGH); delayMicroseconds(10); digitalWrite(TrigPin, LOW); cm = pulseIn(EchoPin, HIGH) / 58.0; //将回波时间换算成cm cm = (int(cm * 100.0)) / 100.0; //保留两位小数 Serial.print(cm); Serial.print("cm"); Serial.println(); delay(1000); }
上传时间： 2013-10-18
上传用户：星仔
As businesses and consumers expect more fromportable electronics, the FPGA industry has beencompelled to re-think how it serves these low-power,cost-sensitive markets. Application classes like
上传时间： 2013-11-08
上传用户：immanuel2006
Abstract: Designers who must interface 1-Wire temperature sensors with Xilinx field-programmable gate arrays(FPGAs) can use this reference design to drive a DS28EA00 1-Wire slave device. The downloadable softwarementioned in this document can also be used as a starting point to connect other 1-Wire slave devices. The systemimplements a 1-Wire master connected to a UART and outputs temperature to a PC from the DS28EA00 temperaturesensor. In addition, high/low alarm outputs are displayed from the DS28EA00 PIO pins using LEDs.
标签： PicoBlaze Create Master Xilinx
上传时间： 2013-11-12
上传用户：大三三
HDB3(High Density Bipolar三阶高密度双极性)码是在AMI码的基础上改进的一种双极性归零码，它除具有AMI码功率谱中无直流分量，可进行差错自检等优点外，还克服了AMI码当信息中出现连“0”码时定时提取困难的缺点，而且HDB3码频谱能量主要集中在基波频率以下，占用频带较窄，是ITU-TG.703推荐的PCM基群、二次群和三次群的数字传输接口码型,因此HDB3码的编解码就显得极为重要了[1]。目前，HDB3码主要由专用集成电路及相应匹配的外围中小规模集成芯片来实现，但集成程度不高，特别是位同步提取非常复杂，不易实现。随着可编程器件的发展，这一难题得到了很好地解决。
上传时间： 2013-11-01
上传用户：lindor
This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
上传时间： 2013-11-01
上传用户：wojiaohs
The CoolRunner-II CPLD is a highly uniform family of fast, low-power devices. Theunderlying architecture is a traditional CPLD architecture, combining macrocells intofunction blocks interconnected with a global routing matrix, the Xilinx AdvancedInterconnect Matrix (AIM). The function blocks use a PLA configuration that allowsall product terms to be routed and shared among any of the macrocells of the functionblock.
上传时间： 2013-11-03
上传用户：1037540470
Xilinx Next Generation 28 nm FPGA Technology Overview Xilinx has chosen 28 nm high-κ metal gate (HKMG) highperformance,low-power process technology and combined it with a new unified ASMBL™ architecture to create a new generation of FPGAs that offer lower power and higher performance. These devices enable unprecedented levels of integration and bandwidth and provide system architects and designers a fully programmable alternative to ASSPs and ASICs.
上传时间： 2013-12-07
上传用户：bruce
WP369可扩展式处理平台-各种嵌入式系统的理想解决方案 ：Delivering unrivaled levels of system performance,flexibility, scalability, and integration to developers,Xilinx's architecture for a new Extensible Processing Platform is optimized for system power, cost, and size. Based on ARM's dual-core Cortex™-A9 MPCore processors and Xilinx’s 28 nm programmable logic,the Extensible Processing Platform takes a processor-centric approach by defining a comprehensive processor system implemented with standard design methods. This approach provides Software Developers a familiar programming environment within an optimized, full featured,powerful, yet low-cost, low-power processing platform.
上传时间： 2013-10-18
上传用户：cursor
波长信号的解调是实现光纤光栅传感网络的关键，基于现有的光纤光栅传感器解调方法，提出一种基于FPGA的双匹配光纤光栅解调方法，此系统是一种高速率、高精度、低成本的解调系统，并且通过引入双匹配光栅有效地克服了双值问题同时扩大了检测范围。分析了光纤光栅的测温原理并给出了该方案软硬件设计，综合考虑系统的解调精度和FPGA的处理速度给出了基于拉格朗日的曲线拟合算法。 Abstract: Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network， based on several existing methods of fiber grating sensor demodulation inadequate， a two-match fiber grating demodulation method was presented. This system is a high-speed， high precision， low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA，this paper gives the curve fitting algorithm based on Lagrange.
上传时间： 2013-10-10
上传用户：zxc23456789
【摘要】本文结合作者多年的印制板设计经验，着重印制板的电气性能，从印制板稳定性、可靠性方面，来讨论多层印制板设计的基本要求。【关键词】印制电路板；表面贴装器件；高密度互连；通孔【Key words】Printed Circuit Board；Surface Mounting Device；High Density Interface；Via一．概述印制板（PCB－Printed Circuit Board）也叫印制电路板、印刷电路板。多层印制板，就是指两层以上的印制板，它是由几层绝缘基板上的连接导线和装配焊接电子元件用的焊盘组成，既具有导通各层线路，又具有相互间绝缘的作用。随着SMT（表面安装技术）的不断发展，以及新一代SMD（表面安装器件）的不断推出，如QFP、QFN、CSP、BGA（特别是MBGA），使电子产品更加智能化、小型化，因而推动了PCB工业技术的重大改革和进步。自1991年IBM公司首先成功开发出高密度多层板（SLC）以来，各国各大集团也相继开发出各种各样的高密度互连（HDI）微孔板。这些加工技术的迅猛发展，促使了PCB的设计已逐渐向多层、高密度布线的方向发展。多层印制板以其设计灵活、稳定可靠的电气性能和优越的经济性能，现已广泛应用于电子产品的生产制造中。下面，作者以多年设计印制板的经验，着重印制板的电气性能，结合工艺要求，从印制板稳定性、可靠性方面，来谈谈多层制板设计的基本要领。
上传时间： 2013-10-08
上传用户：zhishenglu
