设计了一种基于PIC16C71单片机的数字水温配制阀。该配制阀采用NTC热敏电阻作温度传感器，与固定电阻组成简单分压电路作为水温测量电路，利用PIC16C71单片机内置的8位A/D转换器把热敏电阻上的模拟电压转换为数字量，PIC16C71单片机控制直流电机驱动混水阀调节冷热水的混合比例实现水温调节。给出了控制电路图，对水温测量电路的参数选择和测温精度作了详细讨论。实验和分析表明，选用阻值较大的NTC热敏电阻和分压电阻可较好地解决热敏电阻因功耗较大造成的热击穿问题。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上传时间： 2013-11-08
上传用户：Yue Zhong
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
AVR32801: UC3A3 Schematic Checklist Features • Power circuit • Reset circuit • USB connection • External bus interface • ABDAC sound DAC interface • JTAG and Nexus debug ports • Clocks and crystal oscillators • MMC, SD-card, SDHC, SDIO and CE-ATA interface 1 Introduction A good hardware design comes from a proper schematic. Since UC3A3 devices have a fair number of pins and functions, the schematic for these devices can be large and quite complex. This application note describes a common checklist which should be used when starting and reviewing the schematics for a UC3A3 design.
标签： Schematic 32801 UC3A3 Chec
上传时间： 2014-12-26
上传用户：DXM35
，我说说AVR 的集成开发环境。也就是常说的IDE（Integrated Development Environment）。图片比较多，虽然用软件处理过体积，网页可能还是比较慢，还请见谅。 现今世界上的AVR 开发环境可以说是百花齐放了，互相当然各有长短，我们看看都有哪些： 首当其冲的应该还是IAR，为什么呢，因为当初AVR 还在ATMEL 胎中酝酿的时候，IAR 公司 参与了AVR 的设计，因此可以认为IAR 有更为正统的血液，它最了解AVR，它的编译器编出来的 代码应该最优秀。好比你生的孩子还是你最了解——至少相当长一段时间是这样的。事实上，IAR for AVR 确实展现了这个实力，它的功能确实最为强大，无论是源代码编写还是软件乃至硬件仿 真，编译出来的代码也十分优秀。但是事物总是相对存在的，优点有时就意味着缺点。IAR 功能 全面而强悍，代价就是它的软件界面比较复杂，设置选项多，网上的资料也比较少，最要命的是 这个软件非常的贵，好吧你说你有破解版，但是破解文件一般并不通用，而且破解方法一般都稍 显繁琐。以上几条，对于新接触AVR 的人来说，几乎是迈不过的坎。
标签： AVR
上传时间： 2013-10-15
上传用户：weiwolkt
为提高电容测量精度，针对电容式传感器的工作原理设计了基于PIC16LF874单片机电容测量模块。简单阐述了电容测量电路的应用背景和国内外研究现状，介绍了美国Microchip公司PIC16LF874单片机的特性。电容式传感器输出的动态微弱电容信号通过PS021型电容数字转换器把模拟量数据转换成数字量数据，所测数据由PIC16LF874单片机应用程序进行处理、显示和保存。实验结果表明，固定电容标称值为10~20 pF 的测量值相对误差在1%以内，同时也可知被测电容容值越大，测量值和标称值相对误差越小。 Abstract: To improve the accuracy of capacitance measurement，aimed at the principle of work of mercury capacitance acceleration transducer，the design of micro capacitance measurement circuit is based on the key PIC16LF874 chip. Briefly discusses the application of the capacitance measuring circuit for the background and status of foreign researchers，focusing on the United States PIC16LF874 microcontroller features. Capacitive sensor outputed signal through the dynamics of weak PS021-chip capacitors （capacitancedigital converter） to convert analog data into digital data，the measured data from the PIC16LF874 microcontroller application process， display and preservation. Experimental results show that the fixed capacitor 10pF ~ 20pF nominal value of the measured value of relative error is within 1%，but also it canbe seen the value of the measured capacitance larger，measuring value and the nominal value of relative error smaller.
上传时间： 2013-10-29
上传用户：wojiaohs
以太网和CAN总线应用广泛，但由于其通信协议不同，两种总线器件间无法进行数据通信，因此，设计了基于CP2200与C8051F040的以太网总线与CAN总线接口转换电路，并给出部分相关硬件电路与软件设计分析。在保证数据完整和协议可靠的前提下，通过握手协议和简化的以太网协议，不仅实现了以太网数据与CAN数据的转发，同时还顺利的解决了以太网的高速性与CAN的低速率冲突，以及两者数据包之间的大小不同的矛盾。 Abstract: In the development of actual application， Ethernet and CAN bus are used very extensively. Owing to its various communication protocols， the communicating between two kinds of bus device can’t be carried out. Therefore， in order to solve this problem， the Ethernet-CAN bus interface circuit based on CP2200 and C8051F040 was designed in this paper， and part of the related hardware circuit and software design analysis were given. On the condition of data’s integrity and protocols’reliability， through the handshaking protocols and the simplified the Ethernet protocol， not only the data switching between CAN and Ethernet was realized， but also the differ in velocity and packet size was solved.
上传时间： 2013-10-15
上传用户：Ants
提出一种基于凌阳单片机的步进电机加减速的控制方法。采用凌阳科技推出的16位结构工控单片机SPMC75F2413A为控制器，由Allegro公司生产的两相步进电机专用驱动器件SLA7042M构成步进电机的驱动电路，在传统的3段直线加减速控制算法基础上增加至7段S形曲线加减速过程，控制步进电机的启动和停止。实验结果表明，该控制方法克服了直线加减速中不连续、易造成系统冲击的问题，整个系统实现柔性控制，电机启动、停止连续性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
上传时间： 2013-12-08
上传用户：jiangfire
在深入了解Flash存储器的基础上，采用单片机自动检测存储器无效块。主要通过读取每一块的第1、第2页内容，判断该块的好坏，并给出具体的实现过程，以及部分关键的电路原理图和C语言程序代码。该设计最终实现单片机自动检测Flash坏块的功能，并通过读取ID号检测Flash的性能，同时该设计能够存储和读取1GB数据。 Abstract: On the basis of in-depth understanding the Flash chips，this paper designs a new program which using the SCM to detect the invalid block.Mainly through reading the data of the first and second page to detect the invalid block.Specific implementation procedure was given,and the key circuit schematic diagram and C language program code was introduced.This design achieved the function of using the MCU checks the invalid block finally，and increased the function by reading the ID number of Flash to get the performance of the memory.And the design also can write and read1GB data
上传时间： 2013-10-25
上传用户：taozhihua1314
详细介绍工控软件组态王与单片机多机串口通讯的设计原理。分析组态王提供的直接与单片机串口通信方法的优点，给出系统基于RS-485总线传输的接口电路原理图。根据组态王提供的通讯协议和单片机多机串口通讯的原理，给出程序设计流程与思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
上传时间： 2013-12-19
上传用户：tecman
