为了解决磁放大器性能测试过程中，需要对其供给不同数值恒定电流的问题，设计了一种基于DAC7512和单片机的数控恒流源系统。该系统采用AT89C51作为主控器件，将计算机发送的电流控制字命令转换为D/A转换器控制字，通过模拟SPI通信接口，写D/A控制字到DAC7512，从而控制其输出相应数字电压值，经差动缩放电路、电压/电路变换电路和功率驱动电路，最后输出恒定电流。实验结果表明，恒流源输出电流调节范围为-45~+45 mA、精度为±0.1 mA，分辨率达0.024 4 mA，具有应用灵活，外围电路简单，可靠性高的特点。该数控直流恒流源也可为相关产品的测试系统研发提供参考。 Abstract: In order to solve the need to supply different values constant current for the magnetic amplifier in testing process， numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip， which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface， which can output corresponding constant current figures by scaling circuit， the V/I converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA， accuracy is ± 0.1mA， and resolution ratio is 0.024 4mA
上传时间： 2014-12-27
上传用户：invtnewer
针对51单片机系统中常用的A/D转换器价格高、精度低的缺点，介绍TI公司的16 位的带有I2C串行接口的A/D转换器ADS1110的工作原理，给出ADS1110与AT89C51单片机系统的接口电路和软件设计。实践证明，ADS1110具有高性价比和实用性。 Abstract: According to the disadvantages of high expense and low accuracy of the general A/D converter used in MCS51 microchip system,the principle and working process of a high accuracy 16-bit A/D conversion ADS1110 which has I2C bus and belongs to TI Company are proposed here as well as the interface of ADS1110 to AT89C51 and software list.It is proved to be high performance index and practicability.
上传时间： 2013-11-21
上传用户：gyq
为深入了解基于UC3854A控制的PFC变换器中的动力学特性，研究系统参数变化对变换器中分岔现象的影响，在建立Boost PFC变换器双闭环数学模型的基础上，用Matlab软件对变换器中慢时标分岔及混沌等不稳定现象进行了仿真。在对PFC变换器中慢时标分岔现象仿真的基础上，分析了系统参数变化对分岔点的影响，并进行了仿真验证。仿真结果清晰地显示了输入整流电压的幅值变化对系统分岔点的影响。 Abstract: In order to better understand the dynamics characteristic of power factor correction converter based on UC3854A， and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC （Power Factor Correction） converter controller was built. Then， with the help of Matlab， the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.
上传时间： 2013-10-17
上传用户：杜莹12345
介绍了MPC555与CS8900A扩展以太网的硬件设计图。以NUCLUES PLUS操作系统为基础，介绍了网卡软件驱动程序的编制，给出了以太网协议包嵌入NUCLEUS PLUS操作系统的实现方法。 Abstract: The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS operation system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real operation system are discussed.
上传时间： 2013-10-23
上传用户：xiehao13
介绍一种以MSP430单片机为基础的智能频率测量系统，采用硬件逻辑与软件指令相结合的方式控制闸门，实现0 MHz~10 MHz范围内无档切换的等精度测量。 Abstract: An intelligent frequency measurement system based on MSP430 singlechip is introduced. The system uses a way that can combine hardware logic and software instructions to contronl the strobe ,and completes the functions of equal precision in the range of 0MHz~10MHz without shifting
上传时间： 2013-10-28
上传用户：dbs012280
为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
介绍基于ATmega8型单片机的温度测量及加热控制系统。分析系统的工作原理，详尽讨论系统的硬件电路和软件流程。实验证明，该系统工作可靠，稳定性高。 Abstract: The new temperature measuring and heating control system based on ATmega8 MCU is introduced.The system’s working principles is analyzed.The design principles of hardware and software are also discussed in detail.This system has been testified and it works steady and reliably.
上传时间： 2013-11-21
上传用户：caiguoqing
对于沥青混凝土摊铺机自动找平控制系统来说，数字式控制系统的研制是目前的一个方向。介绍了一种基于CAN总线的数字式自动找平控制系统。该系统以CAN总线作为通信方式，PWM控制信号通过C8051F040单片机内部PCA可编程计数器阵列产生，并具有结构简单、信号稳定、实时性强、易扩展的特点。通过硬件实现和系统运行达到了比较理想的控制效果，验证了系统的可行性。 Abstract: A digital auto-leveling control system based on CAN Bus is introduced.It uses CAN Bus as the method of communication and creates PWM signals by programmable counter array in C8051F040 microcontroller. The system is simple, stable, real-time and expansive.
上传时间： 2013-10-09
上传用户：ligi201200
介绍以P87LPC764型单片机为核心的延时型漏电继电器设计方案。该方案可供用户选择实现额定动作电流和5倍额定动作电流下不同的延时动作时间，并有重合闸设定选择功能。解决了以往传统分立元件带来的延时时间离散性大且不易实现的弊端。 Abstract: In this paper, the delay leakage relay based on P87LPC764 is introduced in detail. This system provides different relay times at rating current and 5× rating current for users and also offers superposition brake set selection function. So that it resolves many traditional problems.
上传时间： 2013-11-08
上传用户：zhaiye
在需要实时大量输入汉字的显示控制处理应用中，利用传统单片机实现显示控制的设计方法是较难实现的。带汉字字库的液晶模块的使用使得小容量ROM单片机的大量汉字信息输入与显示成为可能。提出了针对汉字字库编码的二级索引拼音输入检索方法,介绍了以ST7920作为控制器的带汉字字库的液晶显示模块的接口方法及汉字显示和控制原理，给出了通用计算机键盘在单片机中的串行接口，采用该技术可大大增强单片机的汉字输入功能。为小容量ROM单片机的大批量汉字信息处理提供了一种汉字输入解决方案。 Abstract: It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
上传时间： 2013-11-19
上传用户：jhksyghr
