Modern Compiler ImplementatIOn in Java. Second Edition
标签： ImplementatIOn Compiler Edition Modern Second Java in
上传时间： 2019-04-03
上传用户：zsx097
基于ARM_Linux与GPRS的GPS监控终端的研究与实现，这是一篇优秀硕士论文-GPS and GPRS-based ARM_Linux Research and ImplementatIOn o
上传时间： 2013-06-27
上传用户：lhw888
本文介绍了基于单片机AT89C51 的温度控制系统的设计方案与软硬件实现。采用温度传感器DS18B20 采集温度数据，液晶显示屏LCM1602 显示温度数据，AT24C02B 存储温度上下限设定
标签： ImplementatIOn Temperature SingleChip Control
上传时间： 2013-06-03
上传用户：xoxoliguozhi
基于单片机的频率计的实现和protuse仿真-Frequency meter based on single chip ImplementatIOn and protuse simulation
上传时间： 2013-06-04
上传用户：杜莹12345
This application note is intended for system designers who require a hardware ImplementatIOn overview of the development board features such as the power supply, the clock management, the reset control, the boot mode settings and the debug management. It shows how to use the High-density and Medium-density STM32F10xxx product families and describes the minimum hardware resources required to develop an STM32F10xxx application.
上传时间： 2013-04-24
上传用户：epson850
VHDL source codes of the FPGA64, a fpga ImplementatIOn of the C64 computer. Version for the c-one fpga board.
上传时间： 2013-08-05
上传用户：wwwe
Abstract: Transimpedance amplifiers (TIAs) are widely used to translate the current output of sensors like photodiode-to-voltagesignals, since several circuits and instruments can only accept voltage input. An operational amplifier with a feedback resistor fromoutput to the inverting input is the most straightforward ImplementatIOn of such a TIA. However, even this simple TIA circuit requirescareful trade-offs among noise gain, offset voltage, bandwidth, and stability. Clearly stability in a TIA is essential for good, reliableperformance. This application note explains the empirical calculations for assessing stability and then shows how to fine-tune theselection of the feedback phase-compensation capacitor.
标签： Transimpedance Stabilize Amplifier Your
上传时间： 2013-11-13
上传用户：daoyue
设计了水声信号发生系统中的功率放大电路，可将前级电路产生的方波信号转换为正弦信号，同时进行滤波、功率放大，使其满足换能器对输入信号的要求。该电路以单片机AT89C52，集成6阶巴特沃思低通滤波芯片MF6以及大功率运算放大器LM12为核心，通过标准RS232接口与PC进行通信，实现信号增益的程控调节，对干扰信号具有良好的抑制作用。经调试该电路工作稳定正常，输出波形无失真，在输出功率以及放大增益、波纹系数等方面均满足设计要求。 This paper presented a design and ImplementatIOn of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
上传时间： 2013-11-20
上传用户：qwe1234
One of the strengths of Synplify is the Finite State Machine compiler. This is a powerfulfeature that not only has the ability to automatically detect state machines in the sourcecode, and implement them with either sequential, gray, or one-hot encoding. But alsoperform a reachability analysis to determine all the states that could possibly bereached, and optimize away all states and transition logic that can not be reached.Thus, producing a highly optimal final ImplementatIOn of the state machine.
标签： Synplicity Machine Verilog Design
上传时间： 2013-10-23
上传用户：司令部正军级
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype ImplementatIOn.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
上传时间： 2013-11-10
上传用户：1595690
