a8259 可编程中断控制 altera提供 The a8259 is designed to simplify the implementation of the INTERRUPT interface in 8088 and 8086 based microcomputer systems. The device is known as a programmable INTERRUPT controller. The a8259 receives and prioritizes up to 8 INTERRUPTs, and in the cascade mode, this can be expanded up to 64 INTERRUPTs. An asynchronous reset and a clock input have been added to improve operation and reliability.
上传时间： 2014-11-29
上传用户：zhyiroy
多远程二极管温度传感器-Design Considerations for pc thermal management Multiple RDTS (remote diode temperature sensing) provides the most accurate method of sensing an IC’s junction temperature. It overcomes thermal gradient and placement issues encountered when trying to place external sensors. PCB component count decreases when using a device that provides multiple inputs.Better temperature sensing improves product performance and reliability. Disk drive data integrity suffers at elevated temperatures. IBM published an article stating that a 5°C rise in operating temperature causes a 15% increase in the drive’s failure rate. The overall performance of a system can be improved by providing a more accurate temperature measurement of the most critical devices allowing them to run just a few degrees hotter.The LM83 directly senses its own temperature and the temperature of three external PN junctions. One is dedicated to the CPU of choice, the other two go to other parts of your system that need thermal monitoring such as the disk drive or graphics chip. The SMBus-compatible LM83 supports SMBus timeout and logic levels. The LM83 has two INTERRUPT outputs; one for user-programmable limits and WATCHDOG capability (INT), the other is a Critical Temperature Alarm output (T_CRIT_A) for system power supply shutdown.
标签： Considerat Design 远程 二极管
上传时间： 2014-12-21
上传用户：ljd123456
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external INTERRUPT pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
针对UHF读写器设计中，在符合EPC Gen2标准的情况下，对标签返回的高速数据进行正确解码以达到正确读取标签的要求，提出了一种新的在ARM平台下采用边沿捕获统计定时器数判断数据的方法，并对FM0编码进行解码。与传统的使用定时器定时采样高低电平的FM0解码方法相比，该解码方法可以减少定时器定时误差累积的影响；可以将捕获定时器数中断与数据判断解码相对分隔开，使得中断对解码影响很小，实现捕获与解码的同步。通过实验表明，这种方法提高了解码的效率，在160 Kb/s的接收速度下，读取一张标签的时间约为30次/s。 Abstract: Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer INTERRUPT and the data judgment for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
上传时间： 2013-11-10
上传用户：liufei
This example shows how to update at regulate period the WWDG counter using theEarly Wakeup INTERRUPT (EWI). The WWDG timeout is set to 262ms, refresh window set to 41h and the EWI isenabled. When the WWDG counter reaches 40h the EWI is generated and in the WWDGISR the counter is refreshed to prevent a WWDG reset and led connected to PC.07is toggled.The EXTI line9 is connected to PB.09 pin and configured to generate an INTERRUPTon falling edge.In the NVIC, EXTI line9 to 5 INTERRUPT vector is enabled with priority equal to 0and the WWDG INTERRUPT vector is enabled with priority equal to 1 (EXTI IT > WWDG IT). The EXTI Line9 will be used to simulate a software failure: once the EXTI line9event occurs (by pressing Key push-button on EVAL board) the correspondent INTERRUPTis served, in the ISR the led connected to PC.07 is turned off and the EXTI line9pending bit is not cleared. So the CPU will execute indefinitely EXTI line9 ISR andthe WWDG ISR will never be entered(WWDG counter not updated). As result, when theWWDG counter falls to 3Fh the WWDG reset occurs.If the EXTI line9 event don抰 occurs the WWDG counter is indefinitely refreshed inthe WWDG ISR which prevent from WWDG reset. If the WWDG reset is generated, after resuming from reset a led connected to PC.06is turned on. In this example the system is clocked by the HSE(8MHz).
上传时间： 2013-11-11
上传用户：gundamwzc
#include <reg51.h>#include <main.h>#include <INTERRUPT.h> cs5460a应用电路(含源程序)bit code table_odd_even_bit[16]={0,1,1,0,1,0,0,1,1,0,0,1,0,1,1,0}; extern uchar rs485_timeout,pointer_buf485;extern uchar rs485_buf[MAX_485_LEN];extern uchar idata spi_buf[MAX_SPI_LEN];extern uchar pointer_send,send_len; extern uchar count_1s;//extern uint count_2min;extern uint count_10s;extern uchar oper_len,send_offset,chk_sum,send_i;extern bit flag_send_data,flag_level,flag_drdy,flag_data_ok;
上传时间： 2014-01-24
上传用户：heart_2007
温湿度传感器 sht11 仿真程序 sbit out =P3^0; //加热口 //sbit input =P1^1;//检测口 //sbit speek =P2^0;//报警 sbit clo =P3^7;//时钟 sbit ST =P3^5;//开始 sbit EOC =P3^6;//成功信号 sbit gwei =P3^4;//个位 sbit swei =P3^3;//十位 sbit bwei =P3^2;//百位 sbit qwei =P3^1;//千位 sbit speak =P0^0;//报警音 sbit bjled =P0^1;//报警灯 sbit zcled =P0^2;//正常LED int count; uchar xianzhi;//取转换结果 uchar seth;//高时间 uchar setl;//低时间 uchar seth_mi;//高时间 uchar setl_mi;//低时间 bit hlbz;//高低标志 bit clbz; bit spbz; ///定时中断程序/// void t0 (void) INTERRUPT 1 using 0 { TH0=(65536-200)/256;//5ms*200=1000ms=1s TL0=(65536-200)%256; clo=!clo;//产生时钟 if(count>5000) { if(hlbz) { if(seth_mi==0){seth_mi=seth;hlbz=0;out=0;} else seth_mi--; } if(!hlbz) { if(setl_mi==0){setl_mi=setl;hlbz=1;out=1;} else setl_mi--; } count=0; } else count++; } ///////////// ///////延时/////// delay(int i) { while(--i); } ///////显示处理/////// xianshi() { int abcd=0; int i; for (i=0;i<5;i++) { abcd=xianzhi; gwei=1; swei=1; bwei=1; qwei=1; P1=dispcode[abcd/1000]; qwei=0; delay(70); qwei=1; abcd=abcd%1000; P1=dispcode[abcd/100]; bwei=0; delay(70); bwei=1; abcd=abcd%100; P1=dispcode[abcd/10]; swei=0; delay(70); swei=1; abcd=abcd%10; P1=dispcode[abcd]; gwei=0; delay(70); gwei=1; } } doing() { if(xianzhi>100) {bjled=0;speak=1;zcled=1;} else {bjled=1;speak=0;zcled=0;} } void main(void) { seth=60;//h60秒 setl=90;//l90秒 seth_mi=60;//h60秒 setl_mi=90;//l90秒 TMOD=0X01;//定时0 16位工作模式 TH0=(65536-200)/256; TL0=(65536-200)%256; TR0=1; //开始计时 ET0=1; //开定时0中断 EA=1; //开全中断 while(1) { ST=0; _nop_(); ST=1; _nop_(); ST=0; // EOC=0; xianshi(); while(!EOC) { xianshi(); } xianzhi=P2; xianshi(); doing(); } }
上传时间： 2013-11-07
上传用户：我们的船长
a8259 可编程中断控制 altera提供 The a8259 is designed to simplify the implementation of the INTERRUPT interface in 8088 and 8086 based microcomputer systems. The device is known as a programmable INTERRUPT controller. The a8259 receives and prioritizes up to 8 INTERRUPTs, and in the cascade mode, this can be expanded up to 64 INTERRUPTs. An asynchronous reset and a clock input have been added to improve operation and reliability.
上传时间： 2015-01-02
上传用户：panpanpan
SL811开发资料_包含源程序_电路图_芯片资料:SL811HS Embedded USB Host/Slave Controller.The SL811HS is an Embedded USB Host/Slave Controller capable of communicate with either full-speed or low-speed USB peripherals. The SL811HS can interface to devices such as microprocessors, microcontrollers, DSPs, or directly to a variety of buses such as ISA, PCMCIA, and others. The SL811HS USB Host Controller conforms to USB Specification 1.1.The SL811HS USB Host/Slave Controller incorporates USB Serial Interface functionality along with internal full-/low-speed transceivers.The SL811HS supports and operates in USB full-speed mode at 12 Mbps, or at low-speed 1.5-Mbps mode.The SL811HS data port and microprocessor interface provide an 8-bit data path I/O or DMA bidirectional, with INTERRUPT support to allow easy interface to standard microprocessors or microcontrollers such as Motorola or Intel CPUs and many others. Internally,the SL811HS contains a 256-byte RAM data buffer which is used for control registers and data buffer.The available package types offered are a 28-pin PLCC (SL811HS) and a 48-pin TQFP package (SL811HST-AC). Both packages operate at 3.3 VDC. The I/O interface logic is 5V-tolerant.
上传时间： 2013-12-22
上传用户：a82531317
温湿度传感器 sht11 仿真程序 sbit out =P3^0; //加热口 //sbit input =P1^1;//检测口 //sbit speek =P2^0;//报警 sbit clo =P3^7;//时钟 sbit ST =P3^5;//开始 sbit EOC =P3^6;//成功信号 sbit gwei =P3^4;//个位 sbit swei =P3^3;//十位 sbit bwei =P3^2;//百位 sbit qwei =P3^1;//千位 sbit speak =P0^0;//报警音 sbit bjled =P0^1;//报警灯 sbit zcled =P0^2;//正常LED int count; uchar xianzhi;//取转换结果 uchar seth;//高时间 uchar setl;//低时间 uchar seth_mi;//高时间 uchar setl_mi;//低时间 bit hlbz;//高低标志 bit clbz; bit spbz; ///定时中断程序/// void t0 (void) INTERRUPT 1 using 0 { TH0=(65536-200)/256;//5ms*200=1000ms=1s TL0=(65536-200)%256; clo=!clo;//产生时钟 if(count>5000) { if(hlbz) { if(seth_mi==0){seth_mi=seth;hlbz=0;out=0;} else seth_mi--; } if(!hlbz) { if(setl_mi==0){setl_mi=setl;hlbz=1;out=1;} else setl_mi--; } count=0; } else count++; } ///////////// ///////延时/////// delay(int i) { while(--i); } ///////显示处理/////// xianshi() { int abcd=0; int i; for (i=0;i<5;i++) { abcd=xianzhi; gwei=1; swei=1; bwei=1; qwei=1; P1=dispcode[abcd/1000]; qwei=0; delay(70); qwei=1; abcd=abcd%1000; P1=dispcode[abcd/100]; bwei=0; delay(70); bwei=1; abcd=abcd%100; P1=dispcode[abcd/10]; swei=0; delay(70); swei=1; abcd=abcd%10; P1=dispcode[abcd]; gwei=0; delay(70); gwei=1; } } doing() { if(xianzhi>100) {bjled=0;speak=1;zcled=1;} else {bjled=1;speak=0;zcled=0;} } void main(void) { seth=60;//h60秒 setl=90;//l90秒 seth_mi=60;//h60秒 setl_mi=90;//l90秒 TMOD=0X01;//定时0 16位工作模式 TH0=(65536-200)/256; TL0=(65536-200)%256; TR0=1; //开始计时 ET0=1; //开定时0中断 EA=1; //开全中断 while(1) { ST=0; _nop_(); ST=1; _nop_(); ST=0; // EOC=0; xianshi(); while(!EOC) { xianshi(); } xianzhi=P2; xianshi(); doing(); } }
上传时间： 2013-10-16
上传用户：黄蛋的蛋黄
