Features: High efficiency, high reliability, low cost AC input range selected by switch 100% full load burn-in test Protections: Short circuit / Over load Fixed switching frequency at 25KHz Cooling by free air convection 1 year warranty Dimensions: 199*98*38mm (L*W*H)
标签： Switchin Output Single SKS
上传时间： 2013-10-30
上传用户：taa123456
Demonstration circuit 1562A is an engineering toolto design and evaluate the LTC699X-X family ofTimerBlox circuits. The center section of the boardcontains a pre-configured TimerBlox function.DC1562A comes in twelve timing function variationsas outlined in Table 1.Surrounding the center board is a ”playground”prototyping area. The prototyping area has padsfor Dip-8, S8, MS8, or S6 packages with breadboarding connections to each pin and two convenientpower buses and ground bus surrounding theentire area. This area is for conditioning signals tocontrol the timer function and for adding loads controlled in time.
上传时间： 2013-10-18
上传用户：如果你也听说
[PIC项目实战：基于PIC18].Advanced.PIC.Microcontroller.Projects.in.C
标签： PIC Microcontroller Advanced Projects
上传时间： 2013-11-21
上传用户：二驱蚊器
为了提高PCB板制作的效率，改变传统的化学腐蚀制板工艺，使用机械仿形铣制作电路板的方法，设计了以ATMEGA16单片机为核心部件的PCB板雕刻机控制系统。其中包括PCB雕刻机的基本功能、主要硬件电路设计和软件的实现流程，并给出了相关设计电路。重点分析了雕刻机步进电机的驱动电路以及主轴电机的驱动电路，该雕刻机经实际运行，系统工作良好，可有效提高PCB板的制作效率。 Abstract: In order to improve the efficiency of production of PCB board and change the traditional chemical etching plates， using of mechanical copying milling method makes circuit boards，this paper introduces the PCB engraving machine control system used ATMEGA16 microcomputer as the core components. It includes basic function， the hardware circuit design and software realization process， and gives the corresponding circuit design.It analyses the drive circuit of engrawing machine stepper motor and spindle motor in detail. This engraving machine by practical operation， the system works well， which can effectively improve the production efficiency of PCB board.
上传时间： 2013-10-17
上传用户：liangliang123
针对煤矿井下调度及紧急救援系统的需求，以DTMF编解码模块为核心，设计了具有自动拨号功能的新型电话系统。该系统利用MT8880对DTMF信号的编解码功能实现一键拨号和远程设置，通过检测振铃和忙音信号，完成自动摘机和挂机过程，配合AGC等外围电路达到话音清晰流畅的效果。 Abstract: To meet the demand for mine scheduling and emergency rescue system， with using DTMF signal codec as the core， a new telephone system was designed with automatic dialing function. In the system， the DTMF signal encoding and decoding function of MT8880 was used to achieve one-touch dialing and remote setting. The circuit detects the ringing and busy signal， and then completes automatic off-hook and hangup. With AGC(Automatic Gain Control) and other peripheral circuits， the voice was regulated to a clear and smooth effect.
上传时间： 2014-11-18
上传用户：ly1994
为解决电致变色器件的颜色变化受外界环境颜色控制的问题，设计了一种基于单片机的便携式颜色自适应识别电路。与传统颜色识别电路相比较，该电路利用数字式的颜色传感器来获取外界环境颜色，产生的数字颜色信号易于单片机进行处理。在电路中，下位机部分主要负责获取电致变色器件变色参数及控制电致变色器件的颜色变化;而上位机部分主要负责把下位机获取的电致变色器件变色参数进行电压到颜色的曲线拟合，并通过蓝牙通信把拟合曲线参数传递给下位机。结果表明，该电路能自动根据环境颜色提供-4~4 V范围步进为0.1 V的电压来驱动电致变色器件的颜色显示，与传统的颜色识别电路设计相比，识别的精度和速度都得到了明显改善。 Abstract: In this paper， a portable adaptive circuit for color identification(PACCI) based on MCU was designed. Compared to the traditional color identification circuit， the PACCI adopts digital sensor to detect the color data from external environment and further generate digital color data， which can be processed easily by MCU. In PACCI， the slave is mainly responsible for detecting the color parameters of the corresponding elcreochromic device and further driving it. For the master， which is mainly responsible for the color curve fitting based on the parameters of the electrochromic device， and transmits the fitting parameters to the slave through the bluetooth device. The results show that the PACCI can provide the basis voltage range from -4V to 4V automatically based on the colors of external environment with step as 0.1V to drive the corresponding electrochromic device. Compared to the traditional color recognition circuit， the recognition accuracy and speed of PACCI have been improved significantly.
上传时间： 2013-11-09
上传用户：franktu
设计了一种基于PIC16C71单片机的数字水温配制阀。该配制阀采用NTC热敏电阻作温度传感器，与固定电阻组成简单分压电路作为水温测量电路，利用PIC16C71单片机内置的8位A/D转换器把热敏电阻上的模拟电压转换为数字量，PIC16C71单片机控制直流电机驱动混水阀调节冷热水的混合比例实现水温调节。给出了控制电路图，对水温测量电路的参数选择和测温精度作了详细讨论。实验和分析表明，选用阻值较大的NTC热敏电阻和分压电阻可较好地解决热敏电阻因功耗较大造成的热击穿问题。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上传时间： 2013-11-08
上传用户：Yue Zhong
为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
以太网和CAN总线应用广泛，但由于其通信协议不同，两种总线器件间无法进行数据通信，因此，设计了基于CP2200与C8051F040的以太网总线与CAN总线接口转换电路，并给出部分相关硬件电路与软件设计分析。在保证数据完整和协议可靠的前提下，通过握手协议和简化的以太网协议，不仅实现了以太网数据与CAN数据的转发，同时还顺利的解决了以太网的高速性与CAN的低速率冲突，以及两者数据包之间的大小不同的矛盾。 Abstract: In the development of actual application， Ethernet and CAN bus are used very extensively. Owing to its various communication protocols， the communicating between two kinds of bus device can’t be carried out. Therefore， in order to solve this problem， the Ethernet-CAN bus interface circuit based on CP2200 and C8051F040 was designed in this paper， and part of the related hardware circuit and software design analysis were given. On the condition of data’s integrity and protocols’reliability， through the handshaking protocols and the simplified the Ethernet protocol， not only the data switching between CAN and Ethernet was realized， but also the differ in velocity and packet size was solved.
上传时间： 2013-10-15
上传用户：Ants
在深入了解Flash存储器的基础上，采用单片机自动检测存储器无效块。主要通过读取每一块的第1、第2页内容，判断该块的好坏，并给出具体的实现过程，以及部分关键的电路原理图和C语言程序代码。该设计最终实现单片机自动检测Flash坏块的功能，并通过读取ID号检测Flash的性能，同时该设计能够存储和读取1GB数据。 Abstract: On the basis of in-depth understanding the Flash chips，this paper designs a new program which using the SCM to detect the invalid block.Mainly through reading the data of the first and second page to detect the invalid block.Specific implementation procedure was given,and the key circuit schematic diagram and C language program code was introduced.This design achieved the function of using the MCU checks the invalid block finally，and increased the function by reading the ID number of Flash to get the performance of the memory.And the design also can write and read1GB data
上传时间： 2013-10-25
上传用户：taozhihua1314
