Abstract: This application note describes the essential workings of an electrocardiogram (ECG). It discussesfactors that disrupt the ECG signals and make reliable, Highly-accurate electrical characterization difficult. Theindustry-standard solution for ECG electrical characterization, which uses an analog front-end and ADCcombination, is explained. The article then introduces the MAX11040 simultaneous-sampling, sigma-deltaADC as a compelling, Highly integrated solution that eliminates the need for the AFE, and saves both spaceand cost for the application.
上传时间: 2013-12-23
上传用户:sssl
Abstract: This application note describes how sampling clock jitter (time interval error or "TIE jitter") affectsthe performance of delta-sigma digital-to-analog converters (DACs). New insights explain the importanceof separately specifying low-frequency (< 2x passband frequency) and high-frequency or wideband (> 2xpassband frequency) jitter tolerance in these devices. The article also provides an application example ofa simple Highly jittered cycle-skipped sampling clock and describes a method for generating a properbroadband jittered clock. The document then goes on to compare Maxim's audio DAC jitter tolerance tocompetitor audio DACs. Maxim's exceptionally high jitter tolerance allows very simple and low-cost sampleclock implementations.
上传时间: 2013-10-25
上传用户:banyou
One of the strengths of Synplify is the Finite State Machine compiler. This is a powerfulfeature that not only has the ability to automatically detect state machines in the sourcecode, and implement them with either sequential, gray, or one-hot encoding. But alsoperform a reachability analysis to determine all the states that could possibly bereached, and optimize away all states and transition logic that can not be reached.Thus, producing a Highly optimal final implementation of the state machine.
标签: Synplicity Machine Verilog Design
上传时间: 2013-10-23
上传用户:司令部正军级
Finite state machines are widely used in digital circuit designs. Generally, when designing a state machine using an HDL, the synthesis tools will optimize away all states that cannot be reached and generate a Highly optimized circuit. Sometimes, however, the optimization is not acceptable. For example, if the circuit powers up in an invalid state, or the circuit is in an extreme working environment and a glitch sends it into an undesired state, the circuit may never get back to its normal operating condition.
标签: Creating Machines Mentor State
上传时间: 2013-10-08
上传用户:wangzhen1990
The LT®1943 is a Highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
上传时间: 2013-10-19
上传用户:yuhaihua_tony
DC/DC 升压IC:The FP6291 is a current mode boost DC-DC converter. Its PWM circuitry with built-in 0.25 Ω power MOSFET make this regulator Highly power efficient. The internal compensation network also minimizes as much as 6 external component counts. The non-inverting input of error amplifier connects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrush current. The FP6291 is available in the SOT23-6L package and provides space-saving PCB for the application fields.
上传时间: 2013-11-07
上传用户:3294322651
Linear Technology’s DC/DC step-down μModule®regulators are complete switchmode power supplies in asurface-mount package. They include the DC/DC controller,inductor, power switches and supporting circuitry.These Highly integrated regulators also provide an easysolution for applications that require negative outputvoltages. In other words, these products can operate asinverting buck-boost regulators. As a result, the lowestpotential in the circuit is not the standard 0V, but –VOUT,which must be tied to the μModule regulator’s GND. Allsignals are now referred to –VOUT.
上传时间: 2013-10-22
上传用户:ztj182002
For a variety of reasons, it is desirable to charge batteriesas rapidly as possible. At the same time, overchargingmust be limited to prolong battery life. Such limitation ofovercharging depends on factors such as the choice ofcharge termination technique and the use of multi-rate/multi-stage charging schemes. The majority of batterycharger ICs available today lock the user into one fixedcharging regimen, with at best a limited number ofcustomization options to suit a variety of application needsor battery types. The LTC®1325 addresses these shortcomingsby providing the user with all the functionalblocks needed to implement a simple but Highly flexiblebattery charger (see Figure 1) which not only addressesthe issue of charging batteries but also those of batteryconditioning and capacity monitoring.
上传时间: 2013-10-19
上传用户:royzhangsz
为解决直流逆变交流的问题,有效地利用能源,让电源输出最大功率,设计了高性能的基于IR2101最大功率跟踪逆变器,并以SPMC75F2413A单片机作为主控制器。高电压、高速功率的MOSFET或IGBT驱动器IR2101采用高度集成的电平转换技术,同时上管采用外部自举电容上电,能够稳定高效地驱动MOS管。该逆变器可以实现DC/AC的转换,最大功率点的跟踪等功能。实际测试结果表明,该逆变器系统具有跟踪能力强,稳定性高,反应灵敏等特点,该逆变器不仅可应用于普通的电源逆变系统,而且可应用于光伏并网发电的逆变系统,具有广泛的市场前景。 Abstract: To solve the problem of DC-AC inverter, and to utilize solar energy more efficiently, the design of maximum power point tracking inverter based on IR2101 was achieved with a high-performance, which can make the system output power maximum. SPMC75F2413A was adopted as main controller. IR2101 is a high voltage, high speed power MOSFET and IGBT driver. It adopted Highly integrated voltage level transforming technology, and an external bootstrap capacitor was used, which could drive MOS tube efficiently and stably. Many functions are achieved in the system, such as DC/AC conversion, maximun power point tracking, etc. The actual test result shows that the inverter system has characteristics of strong tracking ability, high stability and reacting quickly. The design can not only be used in ordinary power inverter system, but also be used in photovoltaic power inverter system. The design has certain marketing prospects
上传时间: 2013-11-17
上传用户:lliuhhui
针对当前安检力学试验机所能完成的试验种类单一、自动化程度低等问题,提出一种以ATmega128单片机为核心控制器的安检力学试验机的设计。详细阐述了该安检力学试验机各个组成部分的设计原理和方案,并且给出了各部分的软件设计思想和操作流程。经过大量测试试验表明:设计的安检力学试验机可以完成多达十余种的力学安检试验,完全符合相关国家标准,并且具有数据采集精度高、传输速度快、操作安全简便等特点,实现了安检设备的多功能化、数字化和自动化。 Abstract: Currently, many mechanical security testing machines have only one function. The degree of automation of them is low. To solve those problems, a new kind of mechanical security testing machine, using ATmega128 micro-controller as its core controller, has been advanced. It describes the components of the machine. The principles and the scheme in the designing processes are presented in detail, and the software architecture and the operation processes of each part are given. After having done many testing, we have reached the following conclusions: the mechanical security testing machine presented can do over ten mechanical security tests complying with related national standards. It has high data acquisition accuracy and high transmission speed. The operation of the machine is simple and safe. In general, this machine is a multi-functional, Highly automatic, digitalized security testing device.
上传时间: 2013-11-05
上传用户:a67818601