虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

High-Frequency

  • 基于89C52的二极管特性测试器的设计

      利用单片机具有的智能程序控制的特点,设计了基于STC89C52单片机的"二极管特性测试器",可对二极管一般特性进行快速测试。通过稳定线性电流源给二极管加载恒定电流,然后由高精度模数转换器测试其压降,以此为基础可判断二极管好坏、检测二极管极性和测试二极管伏安特性等,避免了用万用表测试只能测得极性而不知其特性这一缺点。可用于电子设计制作过程中对二极管进行快速测试,以确定被测二极管是否满足电路的设计要求。   Abstract:   By making good use of the intelligent control function of the Micro Controller Unit (MCU), the diode trait tester was designed based on the STC89C52,which could be used to test the trait of a diode rapidly. By loading constant current to diode through the stable linear current source, and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC), it can judge whether the diode is good or not, distinguish the polarity of the diode, and test the trait that the diode, which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This device can be used to test the trait of a diode quickly,and to make sure that whether a diode can be used in the electronic design or not.

    标签: 89C52 二极管 特性测试器

    上传时间: 2013-11-13

    上传用户:assef

  • MAXX9257 MAX9258芯片可编程SerDes持续时间计算

    The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.

    标签: SerDes MAXX 9257 9258

    上传时间: 2014-01-24

    上传用户:xingisme

  • 常用PIC系列单片机速查表

    常用PIC系列产品特性一览表 器件  存储器 类型 字数 EEPROM 数据 存储器 RAM I/O 引脚数  ADC (-Bit) 比较 器 运 放 定时器/WDT 串行接口 最高 速度 MHz 封装 PDIP /SOIC ICSP CCP / ECCP 输出电流 (per I/O) 振荡器 频率 (MHz) 参考 电压 VREF LCD PWM 堆栈 深度 High Voltage Wakeup On Change PIC16C432 OTP 2048x14   128 12   2  1-8bit/1-WDT   20 20 √   25 mA  4       0 0 PIC16C433 OTP 2048x14   128 6 4/8    1-8bit/1-WDT   10 18 √   25 mA         0 0 PIC16C505 OTP 1024x12   72 12      1-8bit/1-WDT   20 14 √   25 mA  4       0 0 PIC16C54 OTP 512x12   25 12      1-8bit/1-WDT   20 18/20    20 mA          0 0 PIC16C54A OTP 512x12   25 12      1-8bit/1-WDT   20 18/20    20 mA         0 0 PIC16C54C OTP 512x12   25 12      1-8bit/1-WDT   40 18/20    20 mA          0 0 PIC16C55 OTP 512x12   24 20      1-8bit/1-WDT   20 28    20 mA          0 0 PIC16C554 OTP 512x14   80 13      1-8bit/1-WDT   20 18/20 √   25 mA          0 0 PIC16C558 OTP 2048x14   128 13      1-8bit/1-WDT   20 18/20 √   25 mA          0 0 PIC16C55A OTP 512x12   24 20      1-8bit/1-WDT   40 28    20 mA          0 0 PIC16C56 OTP 1024x12   25 12      1-8bit/1-WDT   20 18/20    20 mA          0 0 PIC16C56A OTP 1024x12   25 12      1-8bit/1-WDT   40 18/20    20 mA         0 0 PIC16C57 OTP 2048x12   72 20      1-8bit/1-WDT   20 28    20 mA          0 0 PIC16C57C OTP 2048x12   72 20      1-8bit/1-WDT   40 28    20 mA          0 0 PIC16C58B OTP 2048x12   73 12      1-8bit/1-WDT   40 18/20    20 mA          0 0 PIC16C620 OTP 512x14   80 13   2  1-8bit/1-WDT   20 18/20 √   25 mA   √      0 0 PIC16C620A OTP 512x14   96 13   2  1-8bit/1-WDT   40 18/20 √   25 mA   √      0 0 PIC16C621 OTP 1024x14   80 13   2  1-8bit/1-WDT   20 18/20 √   25 mA    √      0 0 PIC16C621A OTP 1024x14   96 13   2  1-8bit/1-WDT   40 18/20 √   25 mA   √      0 0 PIC16C622 OTP 2048x14   128 13   2  1-8bit/1-WDT   20 18/20 √   25 mA   √      0 0 PIC16C622A OTP 2048x14   128 13   2  1-8bit/1-WDT   40 18/20/40 √   25 mA   √      0 0 PIC16C62A OTP 2048x14   128 22      2-8bit/1-16bit/1-WDT I²C/ SPI 20 28/ √ 1 25 mA     1   0 0 PIC16C62B OTP 2048x14   128 22      2-8bit/1-16bit/1-WDT I²C /SPI 20 28 √ 1 25 mA     1   0 0 PIC16C63 OTP 4096x14   192 22      2-8bit/1-16bit/1-WDT USART/I²C /SPI 20 28 √ 2 25 mA     2   0 0 PIC16C63A OTP 4096x14   192 22      2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 28 √ 2 25 mA     2   0 0 PIC16C642 OTP 4096x14   176 22   2  1-8bit/1-WDT   20 28 √   25 mA   √      0 0 PIC16C64A OTP 2048x14   128 33      2-8bit/1-16bit/1-WDT I²C /SPI 20 40/44 √ 1 25 mA     1   0 0 PIC16C65A OTP 4096x14   192 33      2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 40/44 √ 2 25 mA     2   0 0 PIC16C65B OTP 4096x14   192 33      2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 40/44 √ 2 25 mA     2   0 0 PIC16C66 OTP 8192x14   368 22      2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 28 √ 2 25 mA     2   0 0 PIC16C662 OTP 4096x14   176 33   2  1-8bit/1-WDT   20 40/44 √   25 mA   √      0 0 PIC16C67 OTP 8192x14   368 33      2-8bit/1-16bit/1-WDT USART/I²C /SPI 20 40/44 √ 2 25 mA     2   0 0 PIC16C71 OTP 1024x14   36 13 4/8    1-8bit/1-WDT   20 18 √   25 mA         0 0 PIC16C710 OTP 512x14   36 13 4/8    1-8bit/1-WDT   20 18/20 √   25 mA         0 0 PIC16C711 OTP 1024x14   68 13 4/8    1-8bit/1-WDT   20 18/20 √   25 mA         

    标签: PIC 单片机 速查

    上传时间: 2013-10-12

    上传用户:xjy441694216

  • 基于PIC18F1320微控制器的信号采集系统

      便携式信号采集在机器健康诊断系统中有较高的应用价值。机器健康诊断的信号特点是包括低频信号。本文研究是为了实现简易而且低成本的低频便携式信号采集。以Microchip公司单片机PIC18F1320为核心设计信号采集电路,实现了信号的采集和保存。系统采用串行电可擦除芯片24LC32A保存数据,经过有线通信,信号数据由串行口通过MAX232芯片输送到微型计算机接收和保存,最后绘制出信号波形。 微型计算机程序采用Visual Basic编程。研究成功采样频率为3 kHz的复杂信号,证明该方案符合设计要求。   Abstract:   Portable signal acquisition is useful in machine health monitoring systems. The signal characteristics of machine health monitoring includes low frequency signals. The goal of this study is to realize simple, inexpensive and portable low frequency signal sampling. This paper provides the project of signal acquisition system design based on PIC18F1320 microcontroller manufactured by the Microchip Technology Incorporation to achieve signal sampling and storage. The system adopted EEPROM 24LC32A to store the signal data. The microcomputer received data via wired link with the MAX232 IC through the serial port. The microcomputer program, programmed in Visual Basic, received the data, stored it and plotted the signal. The study successfully samples 3kHz complicated signals and thus meets the design requirement.

    标签: F1320 1320 PIC 18F

    上传时间: 2013-11-19

    上传用户:moerwang

  • 基于MAX7219的LED数码显示驱动电路设计

      现有基于MAX7219芯片的数码管驱动电路只适用于小尺寸LED,为扩展其使用范围,在介绍动态显示芯片MAX7219功能的基础上,提出了一个基于该芯片的8位高亮度8英寸数码管驱动电路。电路保留了MAX7219芯片的功能强大、编程简单等优点,通过74LS273锁存器和ULN2803达林顿驱动器,实现了对任意大尺寸数码管提供较高电压和电流驱动的静态显示,并亮度可调。   Abstract:   The existing display-driving circuit based on MAX7219 was only applicable to small-size LED. To expand its use, based on the function introduction of dynamic display chip MAX7219, a display-driving circuit for high-brightness 8-bit LED with the size of 8-inch was proposed. The advantages of MAX7219 were retained, such as powerful function and simple programming. Static display with adjustable brightness for large-size LED with higher voltage and current was achieved with the help of 74LS273 and ULN2803.

    标签: 7219 MAX LED 数码显示

    上传时间: 2013-10-23

    上传用户:31633073

  • 基于PIC16C71的数字水温配制阀的设计

      设计了一种基于PIC16C71单片机的数字水温配制阀。该配制阀采用NTC热敏电阻作温度传感器,与固定电阻组成简单分压电路作为水温测量电路,利用PIC16C71单片机内置的8位A/D转换器把热敏电阻上的模拟电压转换为数字量,PIC16C71单片机控制直流电机驱动混水阀调节冷热水的混合比例实现水温调节。给出了控制电路图,对水温测量电路的参数选择和测温精度作了详细讨论。实验和分析表明,选用阻值较大的NTC热敏电阻和分压电阻可较好地解决热敏电阻因功耗较大造成的热击穿问题。   Abstract:   A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal, the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given,the principle,the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.

    标签: PIC 16C C71 16

    上传时间: 2013-11-08

    上传用户:Yue Zhong

  • 基于P89V51RD2的功率因数测量仪设计

    设计一种基于P89V51RD2的功率因数测量仪,采用光电隔离器和专用数码管驱动器。该测量仪是以增强型单片机P89V51RD2为核心,大大简化系统硬件设计。而软件部分采用模块化设计思想,采用中值滤波和小数补偿算法,实现功率因数的高精度测量。实验测试表明,该功率因数测量仪测量精度高,运行稳定可靠。 Abstract:  A power-factor measurement instrument based on P89V51RD2is designed,which uses optical coupler and specific LED drive chip.The power factor measurement instrument uses P89V51RD2as a core of which greatly simplifies the system design.Furthermore,modularization software is developed in detail.The high precision power-factor measuring system is realized by the center value filter and fractional compensation algorithm.Experiments manifests that the power- factor measurement instrument is high precision,steady and reliable.

    标签: P89 89V V51 RD2

    上传时间: 2014-12-27

    上传用户:CHINA526

  • 基于C8051F320的心电监护系统设计

    介绍一种基于C8051单片机的动态心电监护系统。该系统由两部分组成:以C8051F320单片机为核心的数据采集装置和以PC机为平台的分析处理系统。硬件电路功耗低,由单片机自带的USB接口将数据传送给PC机。软件平台采用LabVIEW可视化虚拟仪器系统开发平台,将传统仪器的功能模块集成到计算机中,用户可通过修改虚拟仪器的程序改变其功能。采用USB接口实时传输心电数据,并将数据采集模块设计为计算机外设,使该系统高速快捷、小巧便携。 Abstract:  In this design,a low-cost ECG electrocardiogram monitoring system is introduced,which consists of two parts:data acquisition device based on C8051F320and PC terminal as the analysis and processing system.The system is low-power consumption,the data is transmitted to the PC terminal by USB interface of the C8051F320.By using the visible virtual instrument system developing platform LabVIEW,the traditional instruments function modules are integrated into the computer,so the user can modify virtual instrument software to change its function to meet their needs.Using USB in-terface to realize real-time ECG data transmission,in addition,ECG data acquisition module is designed as the computer peripheral,which makes the syetem high-speed and portable.

    标签: C8051F320 心电监护 系统设计

    上传时间: 2013-11-13

    上传用户:zhangzhenyu

  • H.264高清编解码器的片上系统MG3500

    MG3500SoC是支持H.264高清编解码器的片上系统,内部集成一个嵌入式ARM926处理器,支持高清H.264编解码、MPEG鄄2解码和JPEG编解码。介绍了MG3500SoC的主要性能特点、引脚排列、主要接口功能及在DVR上的应用,以及MG3500SoC及其周围器件的硬件设计,提出了在设计中应注意的问题。 Abstract:  The MG3500System-on-Chip(SoC)is high definition(HD)H.264codec,including ARM926-EJ processor,H.264encoder/decoder,MPEG2decoder and JPEG/MJPEG encoder/decoder.The features,pin assignments,interfaces and the typical application of MG3500in DVR are introduced in this paper.The application hardware circuit between the MG3500SoC and peripheral device are given,the questions which the syetem design needs to pay attention are explained.

    标签: 3500 264 MG 编解码器

    上传时间: 2013-11-12

    上传用户:elinuxzj

  • 基于AT89S52的机载电气盒测试仪的设计

    飞机电网故障时,机载电气盒必须在延迟时间内切断电网,保护机载设备。采用AT89S52设计的电气盒测试仪能够测试电气盒保护功能,测量延迟时间。实际应用结果表明,该测试仪具有测量准确、可靠性高、成本低等优点。 Abstract:  The helicopter-electrical-box must shut off the helicopter power,protect the equipments of the helicopter when the helicopter power is failed.The tester for the helicopter-electrical-box based on AT89S52is used for testing the protect-ing function and measuring the delay time.Application results show this tester has some advantages,such as accurate mea-surement,high dependability,economical cost etc.

    标签: 89S S52 AT 89

    上传时间: 2014-12-27

    上传用户:786334970