Recently a new technology for high voltage Power MOSFETshas been introduced – the CoolMOS™ . Based on thenew device concept of charge compensation the RDS(on) areaproduct for e.g. 600V transistors has been reduced by afactor of 5. The devices show no bipolar current contributionlike the well known tail current observed during the turn-offphase of IGBTs. CoolMOS™ virtually combines the lowswitching losses of a MOSFET with the on-state losses of anIGBT.
标签： COOLMOS
上传时间： 2013-11-14
上传用户：zhyiroy
Abstract: A perfect voltage reference produces a stable voltage independent of any external factors. Real-world voltagereferences, of course, are subject to errors caused by many external factors. One causeof these major errors istemperature. Without care, it is easy to operate a voltage reference outside its operating temperature range. Thisapplication note describes how references respond to temperature changes, and how self-heating can cause a voltagereference to operate outside its recommended temperature range. Once understood, this knowledge can then be used toavoid making this design error.
上传时间： 2013-11-08
上传用户：xianglee
Abstract: The MAX3108 is a complete high-performance universal asynchronous receiver-transmitter (UART) in a tiny 2.1mm ×
标签： Programming Rates Baud 3108
上传时间： 2014-12-23
上传用户：清风冷雨
Abstract: The DS4830 optical microcontroller's analog-to-digital converter (ADC) offset can change with temperature and gainselection. However, the DS4830 allows users to measure the ADC internal offset. The measured ADC offset is added to the ADCoffset register to nullify the offset error. This application note demonstrates the DS4830's ADC internal offset calibration in theapplication program.
上传时间： 2014-12-23
上传用户：萍水相逢
Abstract: A laser module designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(e.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上传时间： 2013-11-13
上传用户：ca05991270
Abstract: Build a composite amplifier featuring high gain, wide bandwidth, good DC accuracy and low distortion
上传时间： 2014-12-23
上传用户：JasonC
Digital convergence, in recent history, has been prevalentin the consumer equipment domain and the designengineers in this area have been struggling with a plethoraof emerging standards and protocols. What lessons can welearn from their struggle? The same dilemmas now existin in-vehicle telematics and infotainment systems but withthe added issues of extremes of temperature, safety,security, and time in market.
上传时间： 2014-12-23
上传用户：9牛10
The LT®6552 is a specialized dual-differencing 75MHzoperational amplifier ideal for rejecting common modenoise as a video line receiver. The input pairs are designedto operate with equal but opposite large-signal differencesand provide exceptional high frequency commonmode rejection (CMRR of 65dB at 10MHz), therebyforming an extremely versatile gain block structure thatminimizes component count in most situations. The dualinput pairs are free to take on independent common modelevels, while the two voltage differentials are summedinternally to form a net input signal.
上传时间： 2014-12-23
上传用户：13691535575
Photodiodes can be broken into two categories: largearea photodiodes with their attendant high capacitance(30pF to 3000pF) and smaller area photodiodes withrelatively low capacitance (10pF or less). For optimalsignal-to-noise performance, a transimpedance amplifi erconsisting of an inverting op amp and a feedback resistoris most commonly used to convert the photodiode currentinto voltage. In low noise amplifi er design, large areaphotodiode amplifi ers require more attention to reducingop amp input voltage noise, while small area photodiodeamplifi ers require more attention to reducing op amp inputcurrent noise and parasitic capacitances.
上传时间： 2013-10-28
上传用户：hanbeidang
High input impedance and a wide input range are twohighly desirable features in a precision analog-to-digitalconverter, and the LTC®2449 delta-sigma ADC has both.With just a few external components, the LTC2449 formsan exceptional measurement system with very high inputimpedance and an input range that extends 300mV beyondthe supply rails.
上传时间： 2013-11-02
上传用户：ywcftc277
