虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

H-Bridge

  • This document teach about the theory of motor control such as H-Bridge and other theories such as PI

    This document teach about the theory of motor control such as H-Bridge and other theories such as PID control, PWN.

    标签: such H-Bridge document theories

    上传时间: 2013-11-25

    上传用户:daguda

  • Atmel mcu temp H bridge exampe

    Atmel mcu temp H bridge exampe

    标签: bridge exampe Atmel temp

    上传时间: 2016-10-30

    上传用户:开怀常笑

  • 基于Atmel ATMega88+ATA682的应用实例 主要功能包括: 1) PWM输出控制 2) H-Bridge,4 POWER FET 驱动 3) 模拟量比较

    基于Atmel ATMega88+ATA682的应用实例 主要功能包括: 1) PWM输出控制 2) H-Bridge,4 POWER FET 驱动 3) 模拟量比较

    标签: H-Bridge ATMega Atmel POWER

    上传时间: 2013-12-12

    上传用户:miaochun888

  • H-Bridge.rar

    protel原理图 H桥电机驱动器 特点:5-7V低电压供电,带升压电路产生12V以上栅极驱动电压,两片so-8小体积mos管半桥驱动芯片保证驱动效果 本电路已应用到多个直流电机驱动板上,最大驱

    标签: H-Bridge

    上传时间: 2013-06-02

    上传用户:zhuoying119

  • 使用H桥变压器驱动器,充电超级电容器

    Abstract: With its small size and large load (10W) capability, the MAX13256 H-Bridge transformer driver is an attractive solution forcharging supercapacitors (supercaps). However, a large capacitance on the output of the circuit can force the driver into fault modeat startup, due to the high initial charge current. This application note presents a solution that allows users to charge a largecapacitance without going into fault.

    标签: H桥变压器 驱动器 充电 超级电容器

    上传时间: 2013-10-20

    上传用户:2728460838

  • Lakewood (MAXREFDES7#)3.3V Input, ±12V (±15V) Output Isolated Power Supply

    Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-Bridge driver for isolated supplies, and two wide input range and adjustable output low-dropout linear regulators (LDOs). Test results and hardware files are included.

    标签: MAXREFDES Lakewood Isolated Output

    上传时间: 2013-11-02

    上传用户:fengzimili

  • Riverside (MAXREFDES8#)3.3V Input, 12V (15V) Output Isolated Power Supply

    Abstract: This document details the Riverside (MAXREFDES8#) subsystem reference design, a 3.3V input, 12V (15V) output, isolated power supply. The Riverside reference design includes a 3W primary-side transformer H-Bridge driver for isolated supplies, and one wide input range and adjustable output low-dropout linear regulator (LDO). Test results and hardware files are included.

    标签: Riverside MAXREFDES Isolated Output

    上传时间: 2013-11-16

    上传用户:会稽剑客

  • 隔离电源设计手册

    Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-Bridge transformer driver for isolated supplies, a wide input range, and adjustable output low-dropout linearregulator (LDO). Test results and hardware files are included.  

    标签: 隔离电源 设计手册

    上传时间: 2013-10-12

    上传用户:jinyao

  • L9945

    AEC-Q100 qualified • 12 V and 24 V battery systems compliance • 3.3 V and 5 V logic compatible I/O • 8-channel configurable MOSFET pre-driver – High-side (N-channel and P-channel MOS) – Low-side (N-channel MOS) – H-Bridge (up to 2 H-Bridge) – Peak & Hold (2 loads) • Operating battery supply voltage 3.8 V to 36 V • Operating VDD supply voltage 4.5 V to 5.5 V • All device pins, except the ground pins, withstand at least 40 V • Programmable gate charge/discharge currents for improving EMI behavior

    标签: configurable Automotive pre-driver suitable channel systems MOSFET fully High side

    上传时间: 2019-03-27

    上传用户:guaixiaolong

  • 半导体制冷温度控制系统的设计研究

    在半导体制冷技术的工作性能及其优缺点研究的基础上,设计了以单片机为核心控制元件,以TEC1-12706为执行元件的半导体制冷温度控制系统。采用高精度分段式PID控制算法配合PWM输出控制的方法实现温度控制;选择数字传感器DS18B20为温度检测元件,还包含1602液晶显示模块、按键调整输入模块和H桥驱动模块等。实际测试表明,该系统结构简单易行,操作方便,工作性能优良,同时针对该系统专门设计的温控算法,使半导体制冷器能更好地适应不同工况而充分发挥其制冷制热工作特性。Based on the study of the performance and advantages and disadvantages of thermoelectric cooler(TEC)technology,a thermoelectric cooling temperature control system with single-chip microcomputer as the core control element and TEC1-12706 as the executive element was designed. High precision piecewise PID control algorithm combined with PWM output control method is adopted to realize temperature control. The digital sensor DS18B20 is selected as the temperature detection element. It also includes 1602 LCD module,key adjustment input module and H bridge drive module. The actual test shows that the system has simple structure,convenient operation and excellent performance. Meanwhile,the temperature control algorithm specially designed for the system can make the semiconductor cooler better adapt to different working conditions and give full play to its refrigeration and heating characteristics.

    标签: 半导体 温度控制系统

    上传时间: 2022-03-27

    上传用户: