The PCA9672 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the FAST-mode Plusfamily.The PCA9672 is a drop-in upgrade for the PCF8574 providing higher FAST-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-23
上传用户：jasonheung
The PCA9673 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the FAST-mode Plusfamily.The PCA9673 is a drop in upgrade for the PCF8575 providing higher FAST-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(400 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-29
上传用户：wkchong
The PCA9674/74A is a drop-in upgrade for the PCF8574/74A providing higher FAST-modePlus I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-22
上传用户：wwwwwen5
Although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a FAST Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
上传时间： 2013-10-14
上传用户：cxl274287265
文章提出了一种精简指令集8 位单片机中, 算术逻辑单元的工作原理。在此基础上, 对比传统PIC 方案、以及在ALU 内部再次采用流水线作业的332 方案、44 方案, 并用Synopsys 综合工具实现了它们。综合及仿真结果表明, 根据该单片机系统要求, 44 方案速度最高, 比332 方案可提高43.9%, 而面积仅比最小的332 方案增加1.6%。在分析性能差异的根本原因之后, 阐明了该方案的优越性。关键词: 单片机, 精简指令集, 算术逻辑单元, 流水线 Abstract: Work principle for ALU in an 8_bit RISC Singlechip microcomputer is described. The traditional PIC scheme, 332 Pipeline scheme and 44 Pipeline scheme are compared on the base of the principle, which are implemented using Synopsys design tools. Results from synthesis and simulation shows that 44 scheme operates the FAST, which is 43.9% FASTer and only 1.6% larger than 332 scheme. The essential reason why the performance is so different is analyzed.Then the advantage of 44 scheme is clarified.Key words: Singlechip, Microcomputer, RISC, ALU, Pipeline
上传时间： 2013-10-18
上传用户：xiaoyaa
This white paper discusses how market trends, the need for increased productivity, and new legislation have accelerated the use of safety systems in industrial machinery. This TÜV-qualified FPGA design methodology is changing the paradigms of safety designs and will greatly reduce development effort, system complexity, and time to market. This allows FPGA users to design their own customized safety controllers and provides a significant competitive advantage over traditional microcontroller or ASIC-based designs. Introduction The basic motivation of deploying functional safety systems is to ensure safe operation as well as safe behavior in cases of failure. Examples of functional safety systems include train brakes, proximity sensors for hazardous areas around machines such as FAST-moving robots, and distributed control systems in process automation equipment such as those used in petrochemical plants. The International Electrotechnical Commission’s standard, IEC 61508: “Functional safety of electrical/electronic/programmable electronic safety-related systems,” is understood as the standard for designing safety systems for electrical, electronic, and programmable electronic (E/E/PE) equipment. This standard was developed in the mid-1980s and has been revised several times to cover the technical advances in various industries. In addition, derivative standards have been developed for specific markets and applications that prescribe the particular requirements on functional safety systems in these industry applications. Example applications include process automation (IEC 61511), machine automation (IEC 62061), transportation (railway EN 50128), medical (IEC 62304), automotive (ISO 26262), power generation, distribution, and transportation. 图Figure 1. Local Safety System
上传时间： 2013-11-05
上传用户：维子哥哥
Express Mode uses an 8-bit wide bus path for FAST configuration of Xilinx FPGAs. Thisapplication note provides information on how to perform Express configuration specifically forthe Spartan™-XL family. The Express mode signals and their associated timing are defined.The steps of Express configuration are described in detail, followed by detailed instructions thatshow how to implement the configuration circui
标签： Spartan-XL Express XAPP FPGA
上传时间： 2014-12-28
上传用户：hewenzhi
A Computer-On-Module, or COM, is a Module with all components necessary for a bootable host computer, packaged as a super component. A COM requires a Carrier Board to bring out I/O and to power up. COMs are used to build single board computer solutions and offer OEMs FAST time-to-market with reduced development cost. Like integrated circuits, they provide OEMs with significant freedom in meeting form-fit-function requirements. For all these reasons the COM methodology has gained much popularity with OEMs in the embedded industry. COM Express® is an open industry standard for Computer-On-Modules. It is designed to be future proof and to provide a smooth transition path from legacy parallel interfaces to LVDS (Low Voltage Differential Signaling) interfaces. These include the PCI bus and parallel ATA on the one hand and PCI Express and Serial ATA on the other hand.
上传时间： 2013-11-05
上传用户：Wwill
CodeWarrior Development Tool Suites are comprehensive integrated developmentenvironments (IDE) that provide a highly visual and automated framework toaccelerate the development of the most complex embedded applications. Acrossmost stages of the development cycle, we offer tools to help configure, debug andoptimize your design built on Freescale MPUs, MCUs, DSPs and DSCs. These toolsuites provide solutions to get your design up and running FAST.
标签： CodeWarrior 开发工具套件
上传时间： 2013-11-07
上传用户：youlongjian0
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available FAST GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
