特点 精确度0.1%满刻度 ±1位数 显示范围-19999-99999可任意规划 可直接量测直流电流/直流电压,无需另接辅助电源 尺寸小(24x48x50mm),稳定性高 分离式端子,配线容易 CE 认证 2.主要規格 辅助电源: None 精确度: 0.1% F.S. ±1 digit(1-100%F.S.) 输入抗阻 : >100Mohm(<2V range) >2Mohm(<2Vrange) < 0.25VA(currEnt ranges) < 1000Vrms(>54V ranges) 最大过载能力: < 150Vrms(<54V ranges)
上传时间： 2013-10-08
上传用户：tiantwo
在研究传统家用燃气报警器的基础上，以ZigBee协议为平台，构建mesh网状网络实现网络化的智能语音报警系统。由于传感器本身的温度和实际环境温度的影响，传感器标定后采用软件补偿方法。为了减少系统费用，前端节点采用半功能节点设备，路由器和协调器采用全功能节点设备，构建mesh网络所形成的家庭内部报警系统，通过通用的电话接口连接到外部的公用电话网络，启动语音模块进行报警。实验结果表明，在2.4 GHz频率下传输，有墙等障碍物的情况下，节点的传输距离大约为35 m，能够满足家庭需要，且系统工作稳定，但在功耗方面仍需进一步改善。 Abstract: On the basis of studying traditional household gas alarm system, this paper proposed the platform for the ZigBee protocol，and constructed mesh network to achieve network-based intelligEnt voice alarm system. Because of the sEnsor temperature and the actual EnvironmEnt temperature, this system design used software compEnsation after calibrating sEnsor. In order to reduce system cost, semi-functional node devices were used as front-End node, however, full-function devices were used as routers and coordinator，constructed alarm system within the family by building mesh network，connected to the external public telephone network through the common telephone interface, started the voice alarm module. The results indicate that nodes transmit about 35m in the distance in case of walls and other obstacles by 2.4GHz frequEncy transmission, this is able to meet family needs and work steadily, but still needs further improvemEnt in power consumption.
上传时间： 2013-10-30
上传用户：swaylong
为了能够满足基站易于选址、优质快速的建站要求和易维护、低成本、高可靠的运行要求，本文对以方舱来实现一体化结构基站做出一番探讨。从系统设计的观点阐述了移动通信高性能基站天线设计的几个关键问题，介绍了智能天线技术在基站中的应用，并且用HFSS软件仿真了一种新型的对称阵子天线，该天线驻波比小于2的带宽可以达到60%，具有良好的宽频带特性。 Abstract: In order to meet the station construction requiremEnt of easy site selection and fast base station， and meet the operational requiremEnt of easy maintEnance， low cost and high reliability， this paper discussed the unified architecture base station using shelter. Several key problems of high performance mobile communication base station antEnna were illustrated from the view of system design， the application of smart antEnna in base station was also introduced. And a novel dipole antEnna was simulated by using HFSS， the VSWR of the antEnna is less than 2， and the bandwidth was reach to 60%. So it has good broadband properties.
上传时间： 2013-11-20
上传用户：linlin
阐述了轨道交通列车定位技术。介绍了在轨道交通系统中列车定位技术的功能，国内外轨道交通中主要采用的列车定位方法，重点论述了几种主要定位技术，并从定位精度、闭塞制式、维护投资成本、抗干扰等方面进行分析比较。提出目前轨道交通定位技术应综合运用，取长补短，多种方法相互融合，才能满足轨道交通中对安全可靠性的要求。 Abstract: Rail train positioning technology is described. The paper introduces the funetions of the train positioning technology in the rail transit system， the main methods of train positioning do mestic and international rail， and focuses on several key methods， analyzes and compares from the positioning accuracy， block system, maintEnance and investmEnt cost， interferEnce and so on， suggested that the currEnt rail positioning technology should be integrated use of positioning method of meriging， learn from each other， to meet the reliability requiremEnts of rail safety.
上传时间： 2013-11-25
上传用户：franktu
为满足无线网络技术具有低功耗、节点体积小、网络容量大、网络传输可靠等技术要求，设计了一种以MSP430单片机和CC2420射频收发器组成的无线传感节点。通过分析其节点组成，提出了ZigBee技术中的几种网络拓扑形式，并研究了ZigBee路由算法。针对不同的传输要求形式选用不同的网络拓扑形式可以尽大可能地减少系统成本。同时针对不同网络选用正确的ZigBee路由算法有效地减少了网络能量消耗，提高了系统的可靠性。应用试验表明，采用ZigBee方式通信可以提高传输速率且覆盖范围大，与传统的有线通信方式相比可以节约40%左右的成本。 Abstract: To improve the proposed technical requiremEnts such as low-ower， small nodes， large capacity and reliable network transmission， wireless sEnsor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This paper provided network topology of ZigBee technology by analysing the componEnt of the nodes and researched ZigBee routing algorithm. Aiming at differEnt requiremEnts of transmission mode to choose the differEnt network topologies form can most likely reduce the system cost. And aiming at differEnt network to choose the correct ZigBee routing algorithm can effectively reduced the network Energy consumption and improved the reliability of the system. Results show that the communication which used ZigBee mode can improve the transmission rate， cover more area and reduce 40% cost compared with traditional wired communications mode.
上传时间： 2013-10-09
上传用户：robter
针对UHF读写器设计中，在符合EPC GEn2标准的情况下，对标签返回的高速数据进行正确解码以达到正确读取标签的要求，提出了一种新的在ARM平台下采用边沿捕获统计定时器数判断数据的方法，并对FM0编码进行解码。与传统的使用定时器定时采样高低电平的FM0解码方法相比，该解码方法可以减少定时器定时误差累积的影响；可以将捕获定时器数中断与数据判断解码相对分隔开，使得中断对解码影响很小，实现捕获与解码的同步。通过实验表明，这种方法提高了解码的效率，在160 Kb/s的接收速度下，读取一张标签的时间约为30次/s。 Abstract: Aiming at the requiremEnt of receiving correctly decoded data from the tag under high-speed communication which complied with EPC GEn2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgmEnt for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiEncy of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
上传时间： 2013-11-10
上传用户：liufei
通过比较各种隔离数字通信的特点和应用范围，指出塑料光纤在隔离数字通信中的优势。使用已经标准化的TOSLINK接口，有利于节省硬件开发成本和简化设计难度。给出了塑料光纤的硬件驱动电路，说明设计过程中的注意事项，对光收发模块的电压特性和频率特性进行全面试验，并给出SPI口使用塑料光纤隔离通信的典型应用电路图。试验结果表明，该设计可为电力现场、电力电子及仪器仪表的设计提供参考。 Abstract: y comparing characteristics and applications area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware developmEnt and design. ThEn it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequEncy characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referEnced for the power field， power electronics and instrumEntation design.
上传时间： 2014-01-10
上传用户：gundan
同步技术是跳频通信系统的关键技术之一，尤其是在快速跳频通信系统中，常规跳频通信通过同步字头携带相关码的方法来实现同步，但对于快跳频来说，由于是一跳或者多跳传输一个调制符号，难以携带相关码。对此引入双跳频图案方法，提出了一种适用于快速跳频通信系统的同步方案。采用短码携带同步信息，克服了快速跳频难以携带相关码的困难。分析了同步性能，仿真结果表明该方案同步时间短、虚警概率低、捕获概率高，同步性能可靠。 Abstract: Synchronization is one of the key techniques to frequEncy-hopping communication system， especially in the fast frequEncy hopping communication system. In convEntional frequEncy hopping communication systems， synchronization can be achieved by synchronization-head which can be used to carry the synchronization information， but for the fast frequEncy hopping， Because modulation symbol is transmitted by per hop or multi-hop， it is difficult to carry the correlation code. For the limitation of fast frequEncy hopping in carrying correlation code， a fast frequEncy-hopping synchronization scheme with two hopping patterns is proposed. The synchronization information is carried by short code， which overcomes the difficulty of correlation code transmission in fast frequEncy-hopping. The performance of the scheme is analyzed， and simulation results show that the scheme has the advantages of shorter synchronization time， lower probability of false alarm， higher probability of capture and more reliable of synchronization.
上传时间： 2013-11-23
上传用户：mpquest
影响无线通讯可靠性和距离的几个因素无线通信距离的主要性能指标有四个：一是发射机的射频输出功率；二是接收机的接收灵敏度；三是系统的抗干扰能力；四是发射/接收天线的类型及增益。而在这四个主要指标中，各国电磁兼容性标准（如北美的FCC、欧洲的En 规范）均只限制发射功率，只要对接收灵敏度及系统的抗干扰能力两项指标进行优化，即可在符合FCC或CE 标准的前提下扩大系统的通信距离。一影响无线通信距离的因素1、地理环境通信距离最远的是海平面及陆地无障碍的平直开阔地， 这也是通常用来评估无线通信设备的通信距离时使用的地理条件。其次是郊区农村、丘陵、河床等半障碍、半开阔环境，通信距离最近的是城市楼群中或群山中，总之，障碍物越密集，对无线通信距离的影响就越大，特别是金属物体的影响最大。一些常见的环境对无线信号的损耗见下表根据路径损耗公式:Ld=32.4+20logf +20logd f=MHZ d=Km 可知信号每损耗6dB，通讯距离就会减少一半!另一个因素就是多路径影响， 所以如果无线模块附近的障碍物较多时也会影响通讯的距离和可靠性。2、电磁环境直流电机、高压电网、开关电源、电焊机、高频电子设备、电脑、单片机等设备对无线通信设备的通信距离均有不同程度的影响。3、气侯条件空气干燥时通信距离较远，空气潮湿（特别是雨、雪天气）通信距离较近，在产品容许的环境工作温度范围内，温度升高会导致发射功率减小及接收灵敏度降低，从而减小了通信距离。
上传时间： 2013-11-13
上传用户：bvdragon
提出了一种以ARM微处理器为控制核心的远程无线视频监控终端的设计方案，其监控终端的硬件设计包括视频采集处理、中央管理控制、无线传输3个模块。并给出了监控终端的软件开发平台和开发模式的系统启动代码、嵌入式Linux系统移植以及驱动程序和应用程序。测试结果表明，该监控终端设计方案合理、有效，基本满足监控需求。 Abstract: A remote wireless video monitoring terminal design， which uses ARM microprocessor as its core control， is proposed in this paper.The hardware design of monitoring terminal system is composed of the video acquisition and processing module， the cEntral managemEnt and control module， wireless transmission module.Meanwhile the monitoring terminal-s software developmEnt platform and developmEnt patterns are designed. Also the design of the system-s start codes， embedded Linux system-s transplantation process， driver and the corresponding applications are givEn. The results showed that the monitoring terminal design is reasonable， effective， basically meet monitoring requiremEnts.
上传时间： 2013-11-13
上传用户：wanqunshEng
