The LTC3546 is a dual output current mode buck regulatorwith fl exible output current partitioning. Beyondthe advantages normally associated with dual outputregulators (reduced size, cost, EMI and part count, withimproved effi ciency), the LTC3546’s outputs can bepartitioned for either 3A and 1A outputs, or two 2A outputs.This increases its application range and simplifi esmultiple supply rail designs. A confi gurable Burst Mode®clamp for each output sets the current transition levelbetween Burst Mode operation and forced continuousconduction mode to optimize effi ciency over the entireoutput range. An adjustable switching frequency up to4MHz and internal power MOSFET switches allow forsmall and compact footprints.
上传时间： 2013-11-04
上传用户：yxgi5
The LTC®4155 and LTC4156 are dual multiplexed-inputbattery chargers with PowerPath™ control, featuring I2Cprogrammability and USB On-The-Go for systems suchas tablet PCs and other high power density applications.The LTC4155’s float voltage (VFLOAT) range is optimizedfor Li-Ion batteries, while the LTC4156 is optimized forlithium iron phosphate (LiFePO4)batteries, supportingsystem loads to 4A with up to 3.5A of battery chargecurrent. I2C controls a broad range of functions and USBOn-The-Go functionality is controlled directly from theUSB connector ID pin.
上传时间： 2013-10-09
上传用户：hanhanj
High voltage buck DC/DC controllers such as the LTC3890(dual output) and LTC3891 (single output) are popular inautomotive applications due to their extremely wide 4V to60V input voltage range, eliminating the need for a snubberand voltage suppression circuitry. These controllersare also well suited for 48V telecom applications whereno galvanic isolation is required.
上传时间： 2013-10-31
上传用户：wwwe
Abstract: This application note describes how to build, debug, and run applications on the on-board MAXQ622microcontroller to interface with the DS8005 dual smart card interface. This is demonstrated in both IAREmbedded Workbench and the Rowley CrossWorks IDE, using sample code provided with the kit.
上传时间： 2013-10-29
上传用户：ddddddd
介绍了一种基于MSP430系列单片机和ADXL203加速度传感器的数字式倾角仪，它不仅可以实现水平度检测，而且可以测量00～3600范围内的任意倾角，分辨率可达O．1。。此外，由于该倾角仪输出为数字结果，因此它也可以与其他的数字设备结合起来，组合成一个功能更加强大的仪器。该数字倾角仪可广泛应用于建筑、机械、道路、桥梁、石油、煤矿和地质勘探等各种需要测量重力参考系下倾角的场合。关键词：MSP430F133单片机；力敏传感器；ADXL203加速度计；角度测量 Abstract：This paper presents a new style digital inclinometer which is developed on the basis of the MSP430F133 MCU and the ADXL203 dual axis aeeelerometer．This inclinometer not only can test levelness，but also can measure any angle between 0。and 360。with an accuracy of 0．1 O．In addition，its output is a digital result，which makes it possible to integrate itself with other digital devices to form a more functional unit．This inclinometer can be widely used in any construction site，oil field，coal-mine or geologic survey and SO on where it will provide the working people with convenience to measure any angles．Key words：MSP430F133 MCU；force sensor；ADXL203 accelerometer；angle measurement
上传时间： 2013-11-14
上传用户：lizhizheng88
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
标签： MULTICHANNEL 5.5 TO RS
上传时间： 2013-10-19
上传用户：ddddddd
基于ADSP-BF561的数字摄像系统设计Design of Digital Video Camera System Based on Digital Signal ProcessorADSP-BF561（浙江大学 信息与通信工程研究所，浙江 杭州 310027） 马海杰, 刘云海摘要：介绍了基于ADI双核的数字信号处理芯片ADSP-BF561 的数字摄像系统实现方案。系统包括硬件和软件两部分，硬件主要有ADSP-BF561及其外围电路、音视频模数/数模转换、CF卡/微硬盘接口等部分。软件主要有操作系统及音视频编解码算法等部分。关键词：ADSP-BF561 ;数字摄像机;微硬盘;MPEG-4;A/D;D/A中图分类号:TN948.41文献标识码:AAbstract: An implementation of digital video camera system based on ADI dual core digital signal processor ADSP-BF561 is introduced. The system can be divided into two parts——hardware and software design. The hardware design includes ADSP-BF561 and perpheral apparatus, A/D,D/A, CF card or Microdrive and so on. The software includes operating system , audio and video coding algorithm.Key words: ADSP-BF561; digital video camera; microdrive; MPEG-4;A/D;D/A
上传时间： 2013-11-10
上传用户：yl1140vista
This application note describes how the existing dual-port block memories in the Spartan™-IIand Virtex™ families can be used as Quad-Port memories. This essentially involves a dataaccess time (halved) versus functionality (doubled) trade-off. The overall bandwidth of the blockmemory in terms of bits per second will remain the same.
上传时间： 2013-11-08
上传用户：lou45566
The SDI standards are the predominant standards for uncompressed digital videointerfaces in the broadcast studio and video production center. The first SDI standard,SD-SDI, allowed standard-definition digital video to be transported over the coaxial cableinfrastructure initially installed in studios to carry analog video. Next, HD-SDI wasto support high-definition video. Finally, dual link HD-SDI and 3G-SDIdoubled the bandwidth of HD-SDI to support 1080p (50 Hz and 60 Hz) and other videoformats requiring more bandwidth than HD-SDI provides.
上传时间： 2013-10-08
上传用户：yjj631
