设计了水声信号发生系统中的功率放大电路，可将前级电路产生的方波信号转换为正弦信号，同时进行滤波、功率放大，使其满足换能器对输入信号的要求。该电路以单片机AT89C52，集成6阶巴特沃思低通滤波芯片MF6以及大功率运算放大器LM12为核心，通过标准RS232接口与PC进行通信，实现信号增益的程控调节，对干扰信号具有良好的抑制作用。经调试该电路工作稳定正常，输出波形无失真，在输出功率以及放大增益、波纹系数等方面均满足设计要求。 This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
上传时间： 2013-11-20
上传用户：qwe1234
經由改變外部閘極電阻(gate resistors)或增加一個跨在汲極(drain)和源極(source)的小電容來調整MOSFET的di/Dt和dv/Dt，去觀察它們如何對EMI產生影響。然後我們可了解到如何在效率和EMI之間取得平衡。我們拿一個有著單組輸出+12V/4.1A及初級側MOSFET AOTF11C60 (αMOSII/11A/600V/TO220F) 的50W電源轉接器(adapter)來做傳導性及輻射性EMI測試。
上传时间： 2014-09-08
上传用户：swing
产品特点： 全系列加装高速保险丝，防止短路电流（di/Dt）对SCR造成损害。 全系列开模成型，体积小、安装、配线容易。 盘面集中多只LED灯头示，遇有状况可立即判断故障原因，迅速排除。 输出特性呈线性，控温最精准。 高品质，高技术产品，绝无干扰现象，加装透明护盖，安全性增加。 独具Soft Start（缓启动）功能，可避免大电流启动。 具有保险丝熔断、电源异常、SCR超温指示及异常接点输出。 内含电子式自动温度侦测器作为散热器超温保护。 冷却风扇全自动控制，温度过高时风扇运转，避免风扇长时间运转，延长风扇寿命。
上传时间： 2013-10-10
上传用户：ouyang426
为了改变目前电网现场作业管理的变电巡检、变电检修试验、输电线路巡检检修等管理系统各自独立运行，信息不能共享，功能、效率受限，建设和维护成本高的现状，提出了采用B/S+C/S构架模式，将各现场作业管理模块和生产MIS（管理系统）集成为一体的现场作业管理系统的设计方案，做到各子系统和生产MIS软硬资源共享，做到同一数据唯一入口、一处录入多处使用。各子系统设备人员等基础信息来源于生产管理系统，各子系统又是生产管理系统的作业数据、缺陷信息的重要来源。经过研究试用成功和推广应用，目前该系统已在江西电网220 kV及以上变电站全面应用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上传时间： 2013-11-15
上传用户：han_zh
为解决直流逆变交流的问题，有效地利用能源，让电源输出最大功率，设计了高性能的基于IR2101最大功率跟踪逆变器，并以SPMC75F2413A单片机作为主控制器。高电压、高速功率的MOSFET或IGBT驱动器IR2101采用高度集成的电平转换技术，同时上管采用外部自举电容上电，能够稳定高效地驱动MOS管。该逆变器可以实现DC/AC的转换，最大功率点的跟踪等功能。实际测试结果表明，该逆变器系统具有跟踪能力强，稳定性高，反应灵敏等特点，该逆变器不仅可应用于普通的电源逆变系统，而且可应用于光伏并网发电的逆变系统，具有广泛的市场前景。 Abstract: To solve the problem of DC-AC inverter， and to utilize solar energy more efficiently， the design of maximum power point tracking inverter based on IR2101 was achieved with a high-performance， which can make the system output power maximum. SPMC75F2413A was adopted as main controller. IR2101 is a high voltage， high speed power MOSFET and IGBT driver. It adopted highly integrated voltage level transforming technology， and an external bootstrap capacitor was used， which could drive MOS tube efficiently and stably. Many functions are achieved in the system， such as DC/AC conversion， maximun power point tracking， etc. The actual test result shows that the inverter system has characteristics of strong tracking ability， high stability and reacting quickly. The design can not only be used in ordinary power inverter system， but also be used in photovoltaic power inverter system. The design has certain marketing prospects
上传时间： 2013-11-17
上传用户：lliuhhui
光伏发电是未来新能源发电重要方向之一，而光伏变流器是光伏发电系统的核心。介绍一种基于微网理念的光伏变流器设计。以该变流器为核心的光伏发电系统可以看做一个小型的微网系统。该系统能根据外部电网情况，工作于并网模式和离网模式。介绍了该系统的各个组成部件的设计以及变流器主电路部分器件的选型。最后，由实验样机进行测试。试验结果验证了电路拓扑结构及控制方案的可行性，也说明了系统参数设计方法的正确性。 Abstract: Solar Photovoltaic generation is an important direction of new energy power generation in the future，while photovoltaic converter is the core of photovoltaic generation system. This paper deals with a study on photovoltaic inverter based on the concept of microgrid. This paper describes a system whose core component is the photovoltaic inverter，can work on grid-connected mode or run independently according to the external situation. The paper simply describes the main components of the system. At last，the prototype was produced and tested. Test result has proved feasibility of circuit topology structure and controlling scheme and shown correctness of system parameters.Key words: PV inverter； microgrid； off-grid； storage battery
上传时间： 2014-12-24
上传用户：Shaikh
锁定放大是微弱信号检测的重要手段。基于相关检测理论，利用开关电容的开关实现锁定放大器中乘法器的功能，提出开关电容和积分器相结合以实现相关检测的方法，并设计出一种锁定放大器。该锁定放大器将微弱信号转化为与之相关的方波，通过后续电路得到正比于被测信号的直流电平，为后续采集处理提供方便。测量数据表明锁定放大器前级可将10-6 A的电流转换为10-1 V的电压，后级通过带通滤波器级联可将信号放大1×105倍。该方法在降低噪声的同时，可对微弱信号进行放大，线性度较高、稳定性较好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上传时间： 2013-11-29
上传用户：黑漆漆
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
在航电系统维护过程中，为解决定位故障的效率和降低维修成本等问题，提出了基于ICD（Interface Control Document，接口控制文件）的1553B总线的信息监控系统模型。该系统运用数据采集卡对总线中传输的信号有无失真、偏差等电气特性进行检测，并使用1553B通讯卡通过测控软件LabWindows/CVI编程与ICD数据库的动态链接，实现总线信息的解析和故障的判断。与传统的维护过程相比，这种模型能够从信号的电气特性以及信息的解析等全方位的去检测判断故障的来源，并且能够广泛在其他1553B总线系统内扩展应用。验证表明该监控系统可以对总线信息进行快速有效地监测分析，能满足应用需求。 Abstract: In the process of avionics system maintenance， to solve the problems such as improving the efficiency of fast orientation to troubles and reducing maintenance cost， system of 1553B bus information monitor model based on ICD was proposed. The system observed whether the data which transmitted on the bus appear distortion and deviation by using data acquisition card. And using 1553B communication card programming of the measure software LabWindows/CVI and the dynamic linking of ICD database， message analysis and fault estimation could be realized. Compared with traditional maintenance， this model can all-dimensionally detect and analyze the source of faults from both electrical characteristics of the signal and message analysis， and it can be widely applied in the other 1553B system. Experiment shown that this monitor system can effectively detect and analyze the bus message and can meet the application requirements.
上传时间： 2013-11-23
上传用户：18752787361
为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
