General Description The LM621 is a bipolar IC designed for commutation of brushless DC motors. The part is compatible with both three- and four-phase motors. It can directly drive the power switching devices used to drive the motor. The LM621 provides an adjustable dead-time circuit to eliminate ``shootthrough'' current spiking in the power switching circuitry. Operation is from a 5V supply, but output swings of up to 40V are accommodated. The part is packaged in an 18-pin, dual-in-line package.
上传时间： 2013-07-24
上传用户：sdq_123
Most circuit designers are familiar with diode dynamiccharacteristics such as charge storage, voltage dependentcapacitance and reverse recovery time. Less commonlyacknowledged and manufacturer specifi ed is diode forwardturn-on time. This parameter describes the timerequired for a diode to turn on and clamp at its forwardvoltage drop. Historically, this extremely short time, unitsof nanoseconds, has been so small that user and vendoralike have essentially ignored it. It is rarely discussed andalmost never specifi ed. Recently, switching regulator clockrate and transition time have become faster, making diodeturn-on time a critical issue. Increased clock rates aremandated to achieve smaller magnetics size; decreasedtransition times somewhat aid overall effi ciency but areprincipally needed to minimize IC heat rise. At clock speedsbeyond about 1MHz, transition time losses are the primarysource of die heating.
上传时间： 2013-10-10
上传用户：谁偷了我的麦兜
Application considerations and circuits for the LT1001 and LT1002 single and dual precision amplifiers are illustrated in a number of circuits, including strain gauge signal conditioners, linearized platinum RTD circuits, an ultra precision dead zone circuit for motor servos and other examples.
上传时间： 2013-10-18
上传用户：dreamboy36
印刷电路板（PCB）设计解决方案市场和技术领军企业Mentor Graphics（Mentor Graphics）宣布推出HyperLynx® PI（电源完整性）产品，满足业内高端设计者对于高性能电子产品的需求。HyperLynx PI产品不仅提供简单易学、操作便捷，又精确的分析，让团队成员能够设计可行的电源供应系统；同时缩短设计周期，减少原型生成、重复制造，也相应降低产品成本。随着当今各种高性能/高密度/高脚数集成电路的出现，传输系统的设计越来越需要工程师与布局设计人员的紧密合作，以确保能够透过众多PCB电源与接地结构，为IC提供纯净、充足的电力。配合先前推出的HyperLynx信号完整性（SI）分析和确认产品组件，Mentor Graphics目前为用户提供的高性能电子产品设计堪称业内最全面最具实用性的解决方案。“我们拥有非常高端的用户，受到高性能集成电路多重电压等级和电源要求的驱使，需要在一个单一的PCB中设计30余套电力供应结构。”Mentor Graphics副总裁兼系统设计事业部总经理Henry Potts表示。“上述结构的设计需要快速而准 确的直流压降(DC Power Drop)和电源杂讯(Power Noise)分析。拥有了精确的分析信息，电源与接地层结构和解藕电容数(de-coupling capacitor number)以及位置都可以决定，得以避免过于保守的设计和高昂的产品成本。”
上传时间： 2013-11-18
上传用户：362279997
Multiple-voltage electronics systems often requirecomplex supply voltage tracking or sequencing, whichif not met, can result in system faults or even permanentfailures in the fi eld. The design diffi culties in meetingthese requirements are often compounded in distributedpowerarchitectures where point-of-load (POL) DC/DCconverters or linear regulators are scattered across PCboard space, sometimes on different board planes. Theproblem is that power supply circuitry is often the lastcircuitry to be designed into the board, and it must beshoehorned into whatever little board real estate is left.Often, a simple, drop-in, fl exible solution is needed tomeet these requirements.
上传时间： 2013-10-08
上传用户：15071087253
利用单片机具有的智能程序控制的特点，设计了基于STC89C52单片机的"二极管特性测试器"，可对二极管一般特性进行快速测试。通过稳定线性电流源给二极管加载恒定电流，然后由高精度模数转换器测试其压降，以此为基础可判断二极管好坏、检测二极管极性和测试二极管伏安特性等，避免了用万用表测试只能测得极性而不知其特性这一缺点。可用于电子设计制作过程中对二极管进行快速测试，以确定被测二极管是否满足电路的设计要求。 Abstract: By making good use of the intelligent control function of the Micro Controller Unit (MCU)， the diode trait tester was designed based on the STC89C52，which could be used to test the trait of a diode rapidly. By loading constant current to diode through the stable linear current source， and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC)， it can judge whether the diode is good or not， distinguish the polarity of the diode， and test the trait that the diode， which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This device can be used to test the trait of a diode quickly，and to make sure that whether a diode can be used in the electronic design or not.
上传时间： 2013-11-13
上传用户：assef
介绍了采用ATmega48单片机实现三相无刷直流电机控制器的方法。利用Atmega48获得带死区的脉宽调制（PWM）、霍尔传感器的换相处理、正弦驱动信号的产生和电机转速的控制等功能。采用该方法的优点是所需的外围器件少，成本低。 Abstract: The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
上传时间： 2013-12-09
上传用户：330402686
The PCA9670 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9670 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-15
上传用户：stella2015
The PCA9671 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plus(Fm+) family.The PCA9671 is a drop in upgrade for the PCF8575 providing higher I2C-bus speeds(1 MHz versus 400 kHz) so that the output can support PWM dimming of LEDs, higherI2C-bus drive (30 mA versus 3 mA) so that many more devices can be on the bus withoutthe need for bus buffers, higher total package sink capacity (400 mA versus 100 mA) thatsupports having all 25 mA LEDs on at the same time and more device addresses (64versus 8) to allow many more devices on the bus without address conflicts.
上传时间： 2013-10-12
上传用户：laomv123
The PCA9672 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9672 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-23
上传用户：jasonheung
