算法导论 英文版 电子书 Introduction to algorithme
标签： Introduction algorithme to 算法
上传时间： 2015-05-03
上传用户：gxmm
WSP is an HTTP to WSP proxy that can be used to forward HTTP requests to WSP, which is used in WAP 1.x. It may be called a reverse WAP gateway, and enables you to test or browse WAP sites with HTTP tools. It also can be used with penetration test tools.
上传时间： 2013-12-16
上传用户：大三三
This ZIP file contains the support files for programming the Infineon C167CR CAN interface. Refer to Application Note 115a for details of this example code.
标签： programming the interface Infineon
上传时间： 2013-12-11
上传用户：2404
This ZIP file contains the support files for programming the Infineon C167CR CAN interface. Refer to Application Note 115a for details of this example code. this is part 2
标签： programming the interface Infineon
上传时间： 2014-12-03
上传用户：lixinxiang
This example demonstrates how to erase, write, and read the on-chip 640-byte EEPROM Data Memory of the Analog Devices ADuC812, ADuC814, ADuC816, and ADuC824 devivces. This example includes a µ Vision2 Project with a target for each supported device.
标签： demonstrates example on-chip EEPROM
上传时间： 2015-05-04
上传用户：wl9454
This example project shows how to use the Idle Power-Saving Mode of the 8051Fx.
标签： Power-Saving the example project
上传时间： 2015-05-04
上传用户：weixiao99
This example program shows how to configure and use the A/D Converter of the following microcontroller: STMicroelectronics ST10F166 After configuring the A/D, the program reads the A/D result and outputs the converted value using the serial port. To run this program... Build the project (Project Menu, Build Target) Start the debugger (Debug Menu, Start/Stop Debug Session) View the Serial Window (View Menu, Serial Window #1) View the A/D converter peripheral (Peripheral Menu, A/D Converter) Run the program (Debug Menu, Go) A debug script (debug.ini) creates buttons that set different analog values in A/D channels. As the program runs, you will see the A/D input and output change. Other buttons create signals that generate sine wave or sawtooth patterns as analog inputs. µ Vision3 users may enable the built-in Logic Analyzer to view, measure and compare these input signals graphically.
标签： microcontroll Converter configure following
上传时间： 2014-12-01
上传用户：独孤求源
How to Use Tables With the JTable (in the API reference documentation) class you can display tables of data, optionally allowing the user to edit the data. JTable doesn t contain or cache data it s simply a view of your data. Here s a picture of a typical table displayed within a scroll pane
标签： documentation the reference display
上传时间： 2013-12-23
上传用户：ayfeixiao
The code is fairly straightforward, except perhaps for the call to convertColumnIndexToModel. That call is necessary because if the user moves the columns around, the view s index for the column doesn t match the model s index for the column. For example, the user might drag the Vegetarian column (which the model considers to be at index 4) so it s displayed as the first column — at view index 0. Since prepareRenderer gives us the view index, we need to translate the view index to a model index so we can be sure we re dealing with the intended column
标签： convertColumnIndexToModel straightforward perhaps fairly
上传时间： 2013-12-10
上传用户：it男一枚
Shows how to use all list selection modes, using a list selection listener that s shared between a table and list.
标签： selection list listener between
上传时间： 2015-05-04
上传用户：jichenxi0730
