12bit 低功耗DAC 数模转换器 The MAX5302 combines a low-power, voltage-output, 12-bit digital-to-analog Converter (DAC) and a precision output amplifier in an 8-pin µMAX package. It operates from a single +5V supply, drawing less than 280µA of supply current.
上传时间： 2017-02-21
上传用户：ckbihu
The AP2406 is a 1.5Mhz constant frequency, slope compensated current mode PWM step-down Converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an external Schottky diode. It is ideal for powering portable equipment that runs from a single cell lithium-Ion (Li+) battery. The AP2406 can supply 600mA of load current from a 2.5V to 5.5V input voltage. The output voltage can be regulated as low as 0.6V. The AP2406 can also run at 100% duty cycle for low dropout operation, extending battery life in portable system. Idle mode operation at light loads provides very low output ripple voltage for noise sensitive applications. The AP2406 is offered in a low profile (1mm) 5-pin, thin SOT package, and is available in an adjustable version and fixed output voltage of 1.2V, 1.5V and 1.8V
上传时间： 2017-02-23
上传用户：w124141
en.CD00004003_Designing with L4973, 3.5 A high efficiency DC-DC Converter,en.CD00004003_Designing with L4973, 3.5 A high efficiency DC-DC Converter
上传时间： 2017-12-24
上传用户：jatcreo@qq.com
DESCRIPTION The Texas Instruments MSP430 family of ultra-low-power microcontrollers consists of several devices featuring different sets of peripherals targeted for various applications. The architecture, combined with five low-power modes, is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 1 μs. The MSP430G2x13 and MSP430G2x53 series are ultra-low-power mixed signal microcontrollers with built-in 16- bit timers, up to 24 I/O capacitive-touch enabled pins, a versatile analog comparator, and built-in communication capability using the universal serial communication interface. In addition the MSP430G2x53 family members have a 10-bit analog-to-digital (A/D) Converter. For configuration details see Table 1. Typical applications include low-cost sensor systems that capture analog signals, convert them to digital values, and then process the data for display or for transmission to a host system.
上传时间： 2018-12-25
上传用户：ygyh
基于TMS320F2812 光伏并网发电模拟装置PROTEL设计原理图+PCB+软件源码+WORD论文文档,硬件采用2层板设计，PROTEL99SE 设计的工程文件，包括完整的原理图和PCB文件，可以做为你的学习设计参考。 摘要：本文实现了一个基于TMS320F2812 DSP芯片的光伏并网发电模拟装置，采用直流稳压源和滑动变阻器来模拟光伏电池。通过TMS320F2812 DSP芯片ADC模块实时采样模拟电网电压的正弦参考信号、光伏电池输出电压、负载电压电流反馈信号等。经过数据处理后，用PWM模块产生实时的SPWM 波，控制MOSFET逆变全桥输出正弦波。本文用PI控制算法实现了输出信号对给定模拟电网电压的正弦参考信号的频率和相位跟踪，用恒定电压法实现了光伏电池最大功率点跟踪（MPPT），从而达到模拟并网的效果。另外本装置还实现了光伏电池输出欠压、负载过流保护功能以及光伏电池输出欠压、过流保护自恢复功能、声光报警功能、孤岛效应的检测、保护与自恢复功能。系统测试结果表明本设计完全满定设计要求。关键词：光伏并网，MPPT，DSP Photovoltaic Grid-connected generation simulator Zhangyuxin，Tantiancheng，Xiewuyang(College of Electrical Engineering, Chongqing University)Abstract: This paper presents a photovoltaic grid-connected generation simulator which is based on TMS320F2812 DSP, with a DC voltage source and a variable resistor to simulate the characteristic of photovoltaic cells. We use the internal AD Converter to real-time sampling the referenced grid voltage signal, outputting voltage of photovoltaic, feedback outputting voltage and current signal. The PWM module generates SVPWM according to the calculation of the real-time sampling data, to control the full MOSFET inverter bridge output sine wave. We realized that the output voltage of the simulator can track the frequency and phase of the referenced grid voltage with PI regulation, and the maximum photovoltaic power tracking with constant voltage regulation, thereby achieved the purpose of grid-connected simulation. Additionally, this device has the over-voltage and over-current protection, audible and visual alarm, islanding detecting and protection, and it can recover automatically. The testing shows that our design is feasible.Keywords: Photovoltaic Grid-connected，MPPT，DSP 目录引言 11. 方案论证 11.1. 总体介绍 11.2. 光伏电池模拟装置 11.3. DC-AC逆变桥 11.4. MOSFET驱动电路方案 21.5. 逆变电路的变频控制方案 22. 理论分析与计算 22.1. SPWM产生 22.1.1. 规则采样法 22.1.2. SPWM 脉冲的计算公式 32.1.3. SPWM 脉冲计算公式中的参数计算 32.1.4. TMS320F2812 DSP控制器的事件管理单元 42.1.5. 软件设计方法 62.2. MPPT的控制方法与参数计算 72.3. 同频、同相的控制方法和参数计算 8
标签： tms320f2812 光伏 并网发电 模拟 protel pcb
上传时间： 2021-11-02
上传用户：
2.7V to 5.5V input voltage Range Efficiency up to 96% 24V Boost Converter with 12A switch current Limit 600KHz fixed Switching Frequency Integrated soft-start Thermal Shutdown Under voltage Lockout Support external LDO auxiliary power supply 8-Pin SOP-PP PackageAPPLICATIONSPortable Audio Amplifier Power SupplyPower BankQC 2.0/Type CWireless ChargerPOS Printer Power SupplySmall Motor Power Supply
标签： XR2981
上传时间： 2021-11-05
上传用户：
ABSTRACTThe flyback power stage is a popular choice for single and multiple output dc-to-dc Converters at powerlevels of 150 Watts or less. Without the output inductor required in buck derived topologies, such as theforward or push-pull Converter, the component count and cost are reduced. This application note will reviewthe design procedure for the power stage and control electronics of a flyback Converter. In these isolatedConverters, the error signal from the secondary still needs to cross the isolation boundary to achieveregulation. By using the UC3965 Precision Reference with Low Offset Error Amplifier on the secondaryside to drive an optocoupler and the UCC3809 Economy Primary Side Controller on the primary side, asimple and low cost 50 Watt isolated power supply is realized.
标签： 隔离
上传时间： 2021-11-24
上传用户：kingwide
This Section covers the design of power transformers used in buck-derived topologies: forward Converter, bridge, half-bridge, and full-wave centertap. Flyback transformers (actually coupled inductors) are covered in a later Section. For more specialized applications, the principles discussed herein will generally apply.
上传时间： 2021-12-16
上传用户：fliang
CHAPTER 1: THE OP AMP CHAPTER 2: OTHER LINEAR CIRCUITS CHAPTER 3: SENSORS CHAPTER 4: RF/IF CIRCUITS CHAPTER 5: FUNDAMENTALS OF SAMPLED DATA SYSTEMS CHAPTER 6: ConverterS CHAPTER 7: DATA Converter SUPPORT CIRCUITS CHAPTER 8: ANALOG FILTERS CHAPTER 9: POWER MANAGEMENT CHAPTER 10: PASSIVE COMPONENTS CHAPTER 11: OVERVOLTAGE EFFECTS ON ANALOG INTEGRATED CIRCUITS CHAPTER 12: PRINTED CIRCUIT BOARD (PCB) DESIGN ISSUES CHAPTER 13: DESIGN DEVELOPMENT TOOLS
上传时间： 2021-12-21
上传用户：wangshoupeng199
The PW5300 is a current mode boost DC-DC Converter. Its PWM circuitry with built-in 0.2Ω powerMOSFET make this regulator highly power efficient. The internal compensation network alsominimizes as much as 6 external component counts. The non-inverting input of error amplifierconnects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrushcurrent. The PW5300 is available in the SOT23-6L package and provides space-saving PCB for theapplication fields
标签： pw5300
上传时间： 2022-02-11
上传用户：jiabin
