Source that implements a Shell for Linux. Can accept at least 2 pipes and 3 sets of Commands.
标签： implements Commands Source accept
上传时间： 2013-12-09
上传用户：chenxichenyue
Linux console Commands for begginers
标签： begginers Commands console Linux
上传时间： 2014-06-15
上传用户：haohaoxuexi
TIMIT data base 2. Run following Matlab Commands to make sure the installation worked correctly:
标签： installation correctly following Commands
上传时间： 2017-07-20
上传用户：dave520l
Run following Matlab Commands to make sure the installation worked correctly. Unlike query function, filterdb does not load all waveforms to memory but returns filtered database object. This is useful when the resulting set of the query is too big to fit in memory. Consequent calls to read function can be made to read content of this filtered database object.
标签： installation following correctly Commands
上传时间： 2013-12-30
上传用户：ainimao
Practical Guide to Linux Commands.
标签： Practical Commands Guide Linux
上传时间： 2014-01-03
上传用户：lhc9102
Command Sheet for Vigor series routers. It describes many useful Commands which can t not be used directly from Web UI.
标签： describes Commands Command routers
上传时间： 2017-09-19
上传用户：2467478207
Commands TRF7960 rfid
上传时间： 2017-09-26
上传用户：王楚楚
随着计算机技术的迅猛发展，受其影响的仪器行业也发生了巨大的变革，即仪器的手动操作使用改为计算机控制自动测试。随着自动测试技术和程控仪器的发展，除了要求物理硬件接口标准化外，也要求软件控制标准化。 硬件方面，从20世纪50代自动测试概念建立起，经过初期专用接口、半专用接口到20世纪80年代中期才普及推广开放式标准接口总线，如RS232串行通信接口总线、GPIB通用接口总线、PXI计算机外围仪器系统总线、VXI块式仪器系统总线等。 软件方面，1987年6月颁布的IEEE488．2（程控仪器消息交换协议）标准首先解决了数据结构方面的问题，但仍将大量的器件语义留给设计者自由定义。1990年4月，国际上九家仪器公司在IEEE488．2基础上提出了SCPI（Standard Commands for Programmable Instruments程控仪器标准命令），才使程控仪器器件数据和命令得到标准化。SCPI的总目标是缩短自动测试系统程序开发时间，保护仪器制造者和使用者双方的硬、软件投资，为仪器控制和数据利用提供广泛兼容的编码环境。 仪器接收到SCPI消息后进行响应：接收字符串消息、词法分析、语法分析、中间代码生成、优化和目标代码生成，语法分析模块的性能直接影响到程控执行效率。为了进一步简化仪器内语法分析模块、提高程控执行效率，本课题提出了在接口电路中加入解析模块的思想，可将控制器发送到仪器的SCPI消息即复杂的ASCII码字符串转变为简单的二进制代码。采用此解析模块将大大简化仪器设计者的软件工作，既能实现仪器语言标准化又能提高仪器对远程 控制的响应速度，这在研究实验室内的自制仪器时将是很有用的。 仪器接口有很多种，本课题主要讨论了RS232和GPIB两种接口。本设计中仪器接口板是独立于仪器的，与仪器单独使用微处理器，若要与仪器连接实现通信只需在两微处理器之间进行通信即可，这样做的目的是：一方面可以不影响仪器的设计和操作，一方面可以实现接口板的通用性和仪器的可换性。针对于RS232接口为一简单接口，我先将工作重心放在软件设计上，主要考虑怎样把复杂的ASCII码字符串解析为简单的二进制代码。针对于GPIB接口，软件设计的主要部分已完成，再把工作重心放在硬件设计上，采用性价比更高的CPID实现GPIB接口芯片NAT9914。为了观察解析结果还加入了LCD显示。本设计在开发通用的、低价的仪器接口板方面做了一个有益的尝试，为进一步的自动测试系统研究打下了基础。 关键词：仪器；SCPI；RS232接口；GPIB接口；CPLD
上传时间： 2013-04-24
上传用户：Andy123456
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus Commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send Commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上传时间： 2013-10-11
上传用户：dianxin61
