Abstract: Engineers often wish that radio susceptibility (RS) or radio immunity could be cured with an antibiotic, a vaccine, or someform of cure-all. Unfortunately, solving the RS problem is not that easy. Indeed, the laws of physics apply. In this article we discusssources of RS. We also offer tips and hints to protect systems, power supplies, printed circuit boards (PCBs), and electroniccomponents from radio frequency interference.
标签： Susceptibility Radio 无线电干扰
上传时间： 2014-12-30
上传用户：旗鱼旗鱼
通过比较各种隔离数字通信的特点和应用范围，指出塑料光纤在隔离数字通信中的优势。使用已经标准化的TOSLINK接口，有利于节省硬件开发成本和简化设计难度。给出了塑料光纤的硬件驱动电路，说明设计过程中的注意事项，对光收发模块的电压特性和频率特性进行全面试验，并给出SPI口使用塑料光纤隔离通信的典型应用电路图。试验结果表明，该设计可为电力现场、电力电子及仪器仪表的设计提供参考。 Abstract: y comparing characteristics and applications area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referenced for the power field， power electronics and instrumentation design.
上传时间： 2014-01-10
上传用户：gundan
Single-Ended and Differential S-Parameters Differential circuits have been important incommunication systems for many years. In the past,differential communication circuits operated at lowfrequencies, where they could be designed andanalyzed using lumped-element models andtechniques. With the frequency of operationincreasing beyond 1GHz, and above 1Gbps fordigital communications, this lumped-elementapproach is no longer valid, because the physicalsize of the circuit approaches the size of awavelength.Distributed models and analysis techniques are nowused instead of lumped-element techniques.Scattering parameters, or S-parameters, have beendeveloped for this purpose [1]. These S-parametersare defined for single-ended networks. S-parameterscan be used to describe differential networks, but astrict definition was not developed until Bockelmanand others addressed this issue [2]. Bockelman’swork also included a study on how to adapt single-ended S-parameters for use with differential circuits[2]. This adaptation, called “mixed-mode S-parameters,” addresses differential and common-mode operation, as well as the conversion betweenthe two modes of operation.This application note will explain the use of single-ended and mixed-mode S-parameters, and the basicconcepts of microwave measurement calibration.
上传时间： 2014-03-25
上传用户：yyyyyyyyyy
Agilent AN 154 S-Parameter Design Application Note S参数的设计与应用 The need for new high-frequency, solid-state circuitdesign techniques has been recognized both by microwaveengineers and circuit designers. These engineersare being asked to design solid state circuitsthat will operate at higher and higher frequencies.The development of microwave transistors andAgilent Technologies’ network analysis instrumentationsystems that permit complete network characterizationin the microwave frequency rangehave greatly assisted these engineers in their work.The Agilent Microwave Division’s lab staff hasdeveloped a high frequency circuit design seminarto assist their counterparts in R&D labs throughoutthe world. This seminar has been presentedin a number of locations in the United States andEurope.From the experience gained in presenting this originalseminar, we have developed a four-part videotape, S-Parameter Design Seminar. While the technologyof high frequency circuit design is everchanging, the concepts upon which this technologyhas been built are relatively invariant.The content of the S-Parameter Design Seminar isas follows:
标签： S参数
上传时间： 2013-12-19
上传用户：aa54
摘要：采用表面组装技术（surface mountt echnology,SMT）进行印制板级电子电路组装是当代组装技术发展的主流。典型的SMT生产线是由高速机和多功能机串联而成，印制电路板（printed circuit board,PCB）上的元器件在贴片机之间的负荷均衡优化问题是SMT生产调度的关键问题。以使贴片时间与更换吸嘴时间之和最大的工作台生产时间最小化为目标构建了负荷均衡模型，开发了相应的遗传算法，并进行了数值实验与算法评价。与生产时间理论下界和现场机器自带软件调度方案的对比表明了模型及其算法的有效性。关键词：印制电路板；表面组装生产线；负荷分配；生产线优化
上传时间： 2013-10-09
上传用户：亚亚娟娟123
ExpressPCB 是一款免费的PCB设计软件，简单实使。可以画双层板。 Our Free PCB software is a snap to learn and use. For the first time, designing circuit boards is simple for the beginner and efficient for the professional. Our board manufacturing service makes top quality two and four layer PCBs. Use our MiniBoard service and pay only $51 for three boards (plus $8 shipping).
标签： ExpressPCB PCB 设计软件
上传时间： 2013-11-15
上传用户：lchjng
Multisim11.0
标签： Multisim Circuit Design Suite
上传时间： 2013-11-18
上传用户：彭玖华
ExpressPCB 是一款免费的PCB设计软件，简单实使。可以画双层板。 Our Free PCB software is a snap to learn and use. For the first time, designing circuit boards is simple for the beginner and efficient for the professional. Our board manufacturing service makes top quality two and four layer PCBs. Use our MiniBoard service and pay only $51 for three boards (plus $8 shipping).
标签： ExpressPCB PCB 设计软件
上传时间： 2013-10-09
上传用户：1047385479
Multisim11.0
标签： Multisim Circuit Design Suite
上传时间： 2013-10-28
上传用户：不懂夜的黑
Abstract: Using a wafer-level package (WLP) can reduce the overall size and cost of your solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.
标签： Considerations Guidelines and Design
上传时间： 2013-11-09
上传用户：ls530720646
