为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control CORE in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
为解决输油管道温度压力参数实时监测的问题，设计了以C8051F930单片机作为控制核心的超低功耗输油管道温度压力远程监测系统。现场仪表使用高精度电桥采集数据，通过433 MHz短距离无线通信网络与远程终端RTU进行通信，RTU通过GPRS网络与PC上位机进行远程数据传输，在上位机中实现数据存储和图形化界面显示，从而实现输油管道温度压力参数的实时监测和异常报警。经实验证明，该系统的12位数据采集精度满足设计要求，漏码率小于1%，正常工作时间超过5个月，能实时有效地监测输油管道的温度压力参数，节省大量人工成本，有效预防管道参数异常造成的经济损失和环境污染。 Abstract: In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control CORE. The high-precision electric bridge was used in field instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between field instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
上传时间： 2013-11-07
上传用户：cuibaigao
针对当前安检力学试验机所能完成的试验种类单一、自动化程度低等问题，提出一种以ATmega128单片机为核心控制器的安检力学试验机的设计。详细阐述了该安检力学试验机各个组成部分的设计原理和方案，并且给出了各部分的软件设计思想和操作流程。经过大量测试试验表明：设计的安检力学试验机可以完成多达十余种的力学安检试验，完全符合相关国家标准，并且具有数据采集精度高、传输速度快、操作安全简便等特点，实现了安检设备的多功能化、数字化和自动化。 Abstract: Currently， many mechanical security testing machines have only one function. The degree of automation of them is low. To solve those problems， a new kind of mechanical security testing machine， using ATmega128 micro-controller as its CORE controller， has been advanced. It describes the components of the machine. The principles and the scheme in the designing processes are presented in detail， and the software architecture and the operation processes of each part are given. After having done many testing， we have reached the following conclusions: the mechanical security testing machine presented can do over ten mechanical security tests complying with related national standards. It has high data acquisition accuracy and high transmission speed. The operation of the machine is simple and safe. In general， this machine is a multi-functional， highly automatic， digitalized security testing device.
上传时间： 2013-11-05
上传用户：a67818601
AVR mega128开发板 联系 杨迪 15336417867 0531-55508458 QQ：1347978253 http://www.easyele.cn 产品概述:AVR mega128开发板是AVRVi开发的基于Atmega128单片机的综合学习开发系统，板载学习资源，集成JTAG仿真器和ISP下载功能，核心板可拆卸独立使用，是你学习AVR单片机，参加各类电子设计竞赛，快速搭建产品的不二选择。AVR mega128开发板亦可以作为单片机培训，高校实验室，课程设计等的实验器材。为了更好的支持客户的学习和开发，此开发板板通讯接口升级为USB接口，方便计算机没有串口的朋友，学习起来更加简捷。货号：EasyAVRM128SK-A 规格： 套 重量：300克 单价498/套。 参数特色： 1.采用核心板和主板分离的形式，在系统的学习之后，可以把核心板直接用于产品中，快速搭建系统。 2.开发板上集成了AVR JTAG ICE仿真器和AVR ISP编程器，超高性价比。 3.您只需要再拥有一台计算机，而不需要购买仿真器和编程器就可以学习开发了。 4.信号调理电路，输入0～10V，轨至轨信号调理。 5.系统资源适中，性价比高。 6.丰富的学习资源，完善的产品支持。 7.EasyAVR教给你从开发环境建立，软件编译，到下载，传真，硬件设计等一系列电子工程师必备的技能，真正学以致用。 AVR mega128开发板板上资源： M128 所有引脚引出，可以利用杜邦头很方便的进行接插扩展，标准2.54针距，可以直接插在万用板上使用，便于进行实验 m128 DB CORE 自带5V、3V3 双路电源稳压 m128 DB CORE 外部晶振多种选择，既可以使用板上已经焊接好的14.7456M的晶振，也可以自己根据自己的需求扩展，晶振的切换通过跳线实现m128 DB CORE 带有JTAG ISP 标准接口 m128 DB CORE 自带一路标准RS232－TTL转换电路，方便实现串口通信 AVR mega128 开发板底板：板载JTAG 仿真器 板载STK500 下载内核 2路独立可调的信号调理电路，可控增益G=0.1-10 2路RS232 串行接口 1路RS485 接口 8 路LED 显示 4 位动态7 段数码管，利用74HC595进行驱动 4 位独立按键 板载IIC 总线PCF8563 实时钟芯片 板载IIC 总线EEPROM AT24c01 1 路有源蜂鸣器 1 路18B20 温度传感器接口，支持单总线器件。(12820可选：10元每个) 1602LCD 接口(送1602液晶) 12232、12864 LCD 接口(LCD12864可选：80元每个) 想找一份好工作吗？ 你想成为一名电子设计工程师吗？ 你对电子设计有浓厚兴趣，而没有工具吗？ 看了很久的程序方面的书籍，却没有实践的机会吗？ 需要开发产品，想快速入门？ 想参加电子设计大赛，机器人大赛吗？ 这个性价比高的专业工具是你的不二选择，它不仅仅是一个AVR mega128 开发板，他还是一个强大的开发工具，通过它进行学习后，对电子产品的设计有进一步的认知，建立起学习ARM，DSP，FPGA的良好基础。AVR mega128 开发板集成了AVR学习板，AVR开发板，AVR编程器，AVR仿真器，AVR核心板的功能，并且可以分开独立使用。 销售清单： 1、调试好的AVR mega128开发板一块(板载JTAG ISP 二合一，已经写入自检程序) 2、ATmega128核心板一块 3、USB供电线一条 4、标准串口(RS232)通讯线缆一条 5、资料光盘一张 6、使用说明书（实验讲义）一本 7、保修卡即订单清单一份 8、赠送LCD1602液晶一块
上传时间： 2013-11-10
上传用户：zm7516678
NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU CORE with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the CORE executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes CORE performance.
上传时间： 2013-11-15
上传用户：zouxinwang
NEC 16位MCU参考手册 The 78K0R/IC3 is a 16-bit single-chip microcontroller that uses a 78K0R CPU CORE and incorporates peripheral functions, such as ROM/RAM, a multi-function timer, a multi-function serial interface, an A/D converter, a programmable gain amplifier (PGA), a comparator, a real-time counter, and a watchdog timer.
上传时间： 2013-11-02
上传用户：努力努力再努力
The LPC1769/68/67/66/65/64 are ARM Cortex-M3 based microcontrollers for embedded applications featuring a high level of integration and low power consumption. The ARM Cortex-M3 is a next generation CORE that offers system enhancements such as enhanced debug features and a higher level of support block integration.
上传时间： 2014-02-20
上传用户：13215175592
MC9S08QG8英文资料 The MC9S08QG8 is the newest member of the Freescale 8-bit family of highly integratedmicrocontrollers, based on the high-performance yet low power HCS08 CORE. The MC9S08QG8is an excellent solution for power-sensitive applications with extended battery life and maximum performance down to 1.8VDC.
上传时间： 2014-12-28
上传用户：dxxx
世界著名厂家单片机简介1.Motorola 单片机:Motorola是世界上最大的单片机厂商,品种全,选择余地大,新产品多,在8位机方面有68HC05和升级产品68HC08,68HC05有30多个系列200多个品种,产量超过20亿片.8位增强型单片机68HC11也有30多个品种,年产量1亿片以上,升级产品有68HC12.16位单片机68HC16也有十多个品种.32位单片机683XX系列也有几十个品种.近年来以PowerPC,Codfire,M.CORE等作为CPU,用DSP作为辅助模块集成的单片机也纷纷推出,目前仍是单片机的首选品牌.Motorola单片机特点之一是在同样的速度下所用的时钟较Intel类单片机低的多因而使得高频噪声低,抗干扰能力强,更适合用于工控领域以及恶劣环境.Motorola 8位单片机过去策略是掩膜为主,最近推出OTP计划以适应单片机的发展,在32位机上,M.CORE在性能和功耗上都胜过ARM7.2.Microchip 单片机:Microchip 单片机是市场份额增长最快的单片机.他的主要产品是16C系列8位单片机,CPU采用RISC结构,仅33条指令,运行速度快,且以低价位著称,一般单片机价格都在1美元以下.Microchip 单片机没有掩膜产品,全部都是OTP器件(现已推出FLASH型单片机).Microchip强调节约成本的最优化设计,是使用量大,档次低,价格敏感的产品.3.Scenix单片机:Scenix单片机的I/O模块最有创意.I/O模块的集成与组合技术是单片机技术不可缺少的重要方面.除传统的I/O功能模块如并行I/O,URT,SPI,I2C,A/D,PWM,PLL,DTMF等,新的I/O模块不断出现,如USB,CAN,J1850,最具代表的是Motorola 32位单片机,它集成了包括各种通信协议在内的I/O模块,而Scenix单片机在I/O模块的处理上引入了虚拟I/O的概念. Scenix单片机采用了RISC结构的CPU,使CPU最高工作频率达50MHz.运算速度接近50MIPS.有了强有力的CPU,各种I/O功能便可以用软件的办法模拟.单片机的封装采用20/28引脚.公司提供各种I/O的库函数,用于实现各种I/O模块的功能.这些软件完成的模块包括多路UART,多种A/D,PWM,SPI,DTMF,FSK,LCD驱动等,这些都是通常用硬件实现起来相当复杂的模块.4.NEC单片机:NEC单片机自成体系,以8位机78K系列产量最高,也有16位,32位单片机.16位单片机采用内部倍频技术,以降低外时钟频率.有的单片机采用内置操作系统.NEC的销售策略注重服务大客户,并投入相当大的技术力量帮助大客户开发新产品.5.东芝单片机:东芝单片机从4位倒64位,门类齐全.4位机在家电领域仍有较大市场.8位机主要有870系列,90系列等.该类单片机允许使用慢模式,采用32KHz时钟功耗低至10uA数量级.CPU内部多组寄存器的使用,使得中断响应与处理更加快捷.东芝公司的32位机采用MIPS3000 ARISC的CPU结构,面向VCD,数字相机,图象处理市场.6.富士通单片机:富士通也有8位,16位和32位单片机,但是8位机使用的是16位的CPU内核.也就是说8位机与16位机指令相同,使得开发比较容易.8位机有名是MB8900系列,16位机有MB90系列.富士通注重服务大公司,大客户,帮助大客户开发产品.7.Epson 单片机:Epson公司以擅长制造液晶显示器著称,故Epson单片机主要为该公司生产的LCD配套.其单片机的LCD驱动做的特别好.在低电压,低功耗方面也很有特色.目前0.9V供电的单片机已经上市,不久LCD显示手表将使用0.5V供电.
上传时间： 2014-12-28
上传用户：leyesome
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCORE. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
标签： Demonstration 3200 USB for
上传时间： 2014-02-27
上传用户：zhangzhenyu
