STi5518 Set-Top-Box DVB-S Loader Source
标签: Set-Top-Box Loader Source DVB-S
上传时间: 2013-12-05
上传用户:jing911003
cledlabel component let you add 7 segment edit box to your application. I added floatingpointformat function that let you add float data to the screen
标签: floatingpointformat application cledlabel component
上传时间: 2017-09-17
上传用户:许小华
The STi7200 is a new generation, high-definition set-top box/DVD decoder chip, and provides very high performance for low-cost HD systems. With enhanced performance over the STx7109, it includes both Windows Media Video 9 and H.264 video decoders for new, low bitrate applications. The STi7200 is able to decode two HD programs
标签: high-definition generation provides decoder
上传时间: 2013-11-29
上传用户:xg262122
S32K148 T-BOX快速入门CONTENTS: Get to know the S32K148 T-BOX Reference Design Board (RDB) S32K148 T-BOX RDB out-of-the-box setup Creating a new S32DS project for the S32K1xx MCU S32DS debugging basics Create a P&E debug configuration
上传时间: 2022-06-20
上传用户:jiabin
基于 S32K148 的 T-BOX/GP-ECU 参考设计采用 NXP 最新的通用汽车电子微控制器S32K1xx 系列的最大资源型号-S32K148,充分利用其片内集成的丰富硬件外设资源和软件开发套件,为用户提供了开箱即可验证的汽车 T-BOX 解决方案的参考设计评估平台。其具有如下功能和特性: 核心 MCU 为 FS32K148UJT0VLQT, 片内集成可运行频率高达 112MHz 并且带有DSP 指令和硬件 IEEE 1577 单精度浮点数处理单元的 ARM Cortex M4F 内核,2MBFlash,256KB SRAM 和 4KB 高性能模拟 EEPROM;
标签: S32K148
上传时间: 2022-07-11
上传用户:
本论文来自于863项目基于光互连自组织内存服务体系(简称MemoryBox)。本文主要研究Memory Box系统中基于可重配置计算架构,软硬件携同设计方法,在XILINX VIRTEX 2 Pro FPGA上设计实现嵌入式系统。由于嵌入式系统是Memory Box工作的平台,所以硬件应具有良好的扩展性、灵活性,软件应具有优良的稳定性。在硬件平台选型时,我们选择的是基于高性能Xilinx VIRTEX2 Pro的自制开发板。嵌入式系统软硬件开发平台选用的是Xilinx EDK、ISE。内核移植所用的交叉开发工具链为powerpc-405-linux-gnu。该交叉开发工具链工作在Red Hat Enterprise LINUX.AS 4平台下。 本论文主要包括三部分工作:首先是硬件设计,其核心是EDK和ISE设计的SOPC工程;然后是嵌入式LINUX内核移植与调试;最后完成存储管理软件的设计。完全用硬件实现系统要求的各种存储管理功能极其困难。而通过移植内核,存储管理软件以运行在Linux内核上的应用软件的形式实现了其功能。存储管理软件要解决共享冲突,负载均衡,远程内存与本地内存的地址一致性以及对海量内存阵列的重新编址等问题,设计出较完善的Memory Box的存储管理模型。
上传时间: 2013-06-11
上传用户:tyler
15.2 已經加入了有關貫孔及銲點的Z軸延遲計算功能. 先開啟 Setup - Constraints - Electrical constraint sets 下的 DRC 選項. 點選 Electrical Constraints dialog box 下 Options 頁面 勾選 Z-Axis delay栏.
上传时间: 2013-10-08
上传用户:王庆才
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for battery operation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation must function at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
标签: Circuitry Operation Single 1017
上传时间: 2013-12-20
上传用户:Wwill
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for batteryoperation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation mustfunction at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
标签: Circuitry Operation Single Cell
上传时间: 2013-10-30
上传用户:hz07104032
In predominantly digital systems it is often necessaryto include linear circuit functions. Traditionally, separatepower supplies have been used to run the linear components(see Box, “Linear Power Supplies—Past, Present,and Future”).
标签: Designing Operation Circuits Linear
上传时间: 2013-11-04
上传用户:sdq_123