通过对程控滤波器的理论分析，在研究MAX262的功能和单片机的SPI总线通信的基础上，提出了基于MAX262的程控滤波器设计方案，设计了程控滤波器的软硬件，并给出了测试结果。 Abstract: By analyzing the programmable filter,the paper puts forward a programmable filter system design based on MAS262 on basic of studying MAS262 features and SPI bus communication.Software and hardware of the programmmable filter are designed,and the test result is given.
上传时间： 2013-11-15
上传用户：wxhwjf
为深入了解基于UC3854A控制的PFC变换器中的动力学特性，研究系统参数变化对变换器中分岔现象的影响，在建立Boost PFC变换器双闭环数学模型的基础上，用Matlab软件对变换器中慢时标分岔及混沌等不稳定现象进行了仿真。在对PFC变换器中慢时标分岔现象仿真的基础上，分析了系统参数变化对分岔点的影响，并进行了仿真验证。仿真结果清晰地显示了输入整流电压的幅值变化对系统分岔点的影响。 Abstract: In order to better understand the dynamics characteristic of power factor correction converter based on UC3854A， and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC （Power Factor Correction） converter controller was built. Then， with the help of Matlab， the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.
上传时间： 2013-10-17
上传用户：杜莹12345
以AVR单片机ATmega8和USB接口器件PDIUSBD12为核心，基于标准的USB1.1协议，设计一种通用USB接口模块，以满足嵌入式系统中对USB接口的需求。对模块的硬件电路或单片机固件程序的硬件接口层稍加修改即可用于其他各种微处理器。该模块可为各种嵌入式系统增加USB接口,实现与USB主机系统通信。 Abstract: Based on AVR microcontroller ATmega8 and USB interface chip PDIUSBD12, a general USB interface module is designed according to USB1.1 protocol for various requirements of embedded systems. Only with few modifications in circuit or hardware abstract layer of firmware, the module can be used on many types of microprocessors. All kinds of embedded systems can realize high speed and stable communication with USB host systems, owing to the facility of this module.
上传时间： 2014-01-08
上传用户：赵云兴
针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移，一般采用光电轴角编码器检测位置信号，输出正交编码脉冲信号。若采用其他方法检测位置信号，必然导致电路设计复杂，可靠性降低。因此，提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理，LS7266R1与单片机的接口硬件设计，以及主程序软件流程图。巧妙地把力量传感器，位移传感器等机械运动状态的压力或拉力以及位置坐标，变成了电压信号和电脉冲数字信号，供A/D测量和LS7266R1计数，从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上传时间： 2013-11-02
上传用户：yl1140vista
介绍一种应用于长城赛弗SUV汽车后门车窗多功能控制器，能实现对电动玻璃车窗、车窗雨刮器、喷水器以及电加热除霜器等控制。介绍了基于NXP P89LPC922单片机多功能汽车后车窗控制器的控制功能、硬件电路原理和软件设计方法。 Abstract: This paper presents a multipurpose automotive rear windows controller for CHANGCHENG SAFE SUV.The controller can control rear power-operated window,rear wiping,washing water pump and rear defroster of the windows. In this paper, it is introduced in detail that the functions and the design of the circuit and program of the controller based on NXP P89LPC922 MCU.
上传时间： 2013-11-13
上传用户：z754970244
介绍了MPC555与CS8900A扩展以太网的硬件设计图。以NUCLUES PLUS操作系统为基础，介绍了网卡软件驱动程序的编制，给出了以太网协议包嵌入NUCLEUS PLUS操作系统的实现方法。 Abstract: The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS operation system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real operation system are discussed.
上传时间： 2013-10-23
上传用户：xiehao13
主要介绍了以PIC18F2480单片机为处理器，基于可编程多路开关检测接口器件MC33993实现的车用多路开关检测接口电路的设计。该设计克服了以往基于分立元件的检测接口电路的弊端，简化了接口电路设计，保证了车用开关工作的可靠性和安全性。 Abstract: The design of automotive multiple switch detection interface circuit based on MC33993 is introduced mainly which adopts PIC18F2480 single chip microprocessor.This circuit overcomes shortage of traditional design which contains many schism elements, and the application of MC33993 also predigests the whole design of interface circuit and guarantees the dependability and security of the switch.
上传时间： 2013-11-19
上传用户：star_in_rain
介绍了基于单片机航空交流电参数测试仪的系统设计。以Silicon Labs公司的C8051F005单片机为核心设计出数据采集板，通过RS-232串口与上位机通讯。运用Lab Windows/CVI编写的上位机软件实现信号的检测以及波形和数据的显示，给出了测试仪硬件电路的组成和软件流程图。本系统具有硬件结构简单、容易实现和成本低等特点，在实际应用中其稳定性、精确性均能满足客户要求。 Abstract: The design of aeronautics AC parameters tester based on the single-chip is introduced.The core component of data acquisition board is C8051F005 single chip of Silicon Labs Company,and communication with PC through RS-232. The signal processing software programmed with LabWindows/CVI can be used successfully to fulfill inspection of signal and display of the waveform and data. The hardware and software configuration of test instrument are provided.The hardware of the system is simple, and can be easily realized.The stability and precision of the measurement instrument are enough to meet the requirements.
上传时间： 2013-11-18
上传用户：wang5829
介绍了基于单片机C8051F020的通用串口适配器的设计与实现方法，即由单片机控制的智能化一对多口收发信号转换器。通过采用C51对单片机进行编程，控制与RS-232（标准RS-232电平）、RS232(TTL电平)、RS-422接口的数据通信；采用C++ Builder作为开发平台，通过RS-232接口实现上位机对适配器各个通信端口的控制。 Abstract: Design and realization of a universal serial port adapter based on the MCU C8051F020 are introduced.The adapter is an intelligent one-to-more receiving and transmitting signal converter controlled by the MCU. By programming the MCU with the language C51,MCU control data communication between the MCU and RS-232(RS-232 level),RS-232(TTL level),RS-422 port; Using C++ Builder as the development plane, by one RS232 port, the upper PC can control each of the communication port of the adapter.
上传时间： 2013-11-19
上传用户：hebanlian
介绍了电力操作电源与智能电池巡检系统的特点，给出了一种基于超低功耗单片机MSP430 F149针对中小型变电站自动化运行的专用设备的基本设计原理及实现方法，最后给出了详细硬件构成和软件实现。该系统能满足中小型变电站安全、可靠、自动运行的要求，并通过与上位机的串行通信实现变电站的远程管理和控制。 Abstract: The characters of the intelligent battery data logging system of the electric operation power are introduced.The basic design principle and the implemented methods of the special equipment which only designed for the middle or small transformer substation based on MSP430F149 are prescribed. Finally, the hardware block diagram and the software flow chart are also given. The function that the system finally needs to realize can basically meet with the middle or small transformer substation’s satisfy, reliably,and automatic running.And it can also realize the transformer substation long-distance management and control by serial communicating with the host computer.
上传时间： 2013-11-25
上传用户：黄华强
