A system simulation environment in Matlab/Simulink of RFID is constructed in this paper. Special attention is emphasized on the analog/RF circuit.Negative effects are concerned in the system model,such as phase noise of the local oscillator,TX-RX coupling,reflection of the environment, AWGN noise,DC offset,I/Q mismatch,etc.Performance of the whole system can be evaluated by changing the coding method,parameters of building blocks,and operation distance.Finally,some simulation results are presented in this paper.
标签： environment constructed simulation Simulink
上传时间： 2014-01-09
上传用户：zhangliming420
The ability to write efficient, high-speed arithmetic routines ultimately depends upon your knowledge of the elements of arithmetic as they exist on a computer. That conclusion and this book are the result of a long and frustrating search for information on writing arithmetic routines for real-time embedded systems. With instruction cycle times coming down and clock rates going up, it would seem that speed is not a problem in writing fast routines. In addition, math coprocessors are becoming more popular and less expensive than ever before and are readily available. These factors make arithmetic easier and faster to use and implement. However, for many of you the systems that you are working on do not include the latest chips or the faster processors. Some of the most widely used microcontrollers used today are not Digital Signal Processors (DSP), but simple eight-bit controllers such as the Intel 8051 or 8048 microprocessors.
标签： arithmetic high-speed ultimately efficient
上传时间： 2014-11-30
上传用户：lizhen9880
Welcome to the software files for the ADS8361 to TMS320F2812! There are two project files in each of the folders McBSP, SPI and Both. Mode II and IV are explored using the McBSP port alone, as well as the SPI port. These projects are located in the SPI and McBSP folders. Modes I and III are explored using both McBSP and SPI. In Mode I, the M0 and M1 pins are controlled by use of the jumper on the evaluation module. A0 is controlled by the DX pin of the McBSP port. In Mode III, the A0, M0 and M1 pins are controlled via GPIO functions of PortF. The "SRC", "CMD" and "INCLUDE" files in the archive are from "C28x Peripheral Examples in C" (document # SPRC097). If you have questions about this or other Data Converter products, feel free to e-mail us at:
标签： files the software Welcome
上传时间： 2015-12-16
上传用户：lixinxiang
Carrier-phase synchronization can be approached in a general manner by estimating the multiplicative distortion (MD) to which a baseband received signal in an RF or coherent optical transmission system is subjected. This paper presents a unified modeling and estimation of the MD in finite-alphabet digital communication systems. A simple form of MD is the camer phase exp GO) which has to be estimated and compensated for in a coherent receiver. A more general case with fading must, however, allow for amplitude as well as phase variations of the MD. We assume a state-variable model for the MD and generally obtain a nonlinear estimation problem with additional randomly-varying system parameters such as received signal power, frequency offset, and Doppler spread. An extended Kalman filter is then applied as a near-optimal solution to the adaptive MD and channel parameter estimation problem. Examples are given to show the use and some advantages of this scheme.
标签： synchronization Carrier-phase multiplicativ approached
上传时间： 2013-11-28
上传用户：windwolf2000
This paper investigates the design of joint frequency offset and carrier phase estimation of a multi-frequency time division multiple access (MF-TDMA) demodulator that is applied to a digital video broadcasting—return channel system via satellite (DVB-RCS). The proposed joint estimation algorithm is based on the interpolation technique for two correlation values in the frequency and phase domains. This simple interpolation technique can significantly improve frequency and phase resolution capabilities of the proposed technique without increasing the number of the correlation values. In addition, the overall block diagram of a digital communications receiver for DVB-RCS is presented, which was designed using the proposed estimation algorithms. Index Terms—Carrier phase estimation, DVB-RCS, frequency offset estimation, interpolation, joint estimation, MF-TDMA.
标签： investigates estimation frequency carrier
上传时间： 2015-12-30
上传用户：ls530720646
The TMS320C64x™ DSPs (including the TMS320DM642 device) are the highest-performance fixed-point DSP generation in the TMS320C6000™ DSP platform. The TMS320DM642 (DM642) device is based on the second-generation high-performance, advanced VelociTI™ very-long-instruction-word (VLIW) architecture (VelociTI.2™ ) developed by Texas Instruments (TI), making these DSPs an excellent choice for digital media applications. The C64x™ is a code-compatible member of the C6000™ DSP platform.
标签： highest-performance fixed-point TMS 320
上传时间： 2013-12-21
上传用户：watch100
实用的单片机开发与应用程序，包括：中值滤波子程序，AD转换类程序，16、32位整型数开方，单片机音乐程序--祝你平安。对初学者很有帮助的。MCU development and practical applications, including: median filter subroutine, AD converter type of proceeding, 16,32-bit integer number prescribing, SCM music program - I wish you peace. Helpful for beginners.
上传时间： 2016-01-27
上传用户：sunjet
aDABOOST This package contains the following files: learner.jar - is a platform independent java package. In order to run it on windows/linux open the command prompt/shell and type the command "java -jar learner.jar". Make sure the java installation path is set in the system enviroment. learner.exe - A windows executable version of the application. Doubleclick to run. learner.pdf - The digital version of the report. SRC\ - The source code of the program is in this directory
标签： independent following aDABOOST contains
上传时间： 2014-12-05
上传用户：xsnjzljj
An instrument other than a watch for measuring or indicating time, especially a mechanical or electronic device having a numbered dial and moving hands or a digital display.break down the enemy s resistance
标签： instrument especially indicating mechanical
上传时间： 2014-01-11
上传用户：二驱蚊器
通过信号与系统以及数字信号处理中所学的理论知识，基于调幅和调频的基本原理，运用产生信号的两种基本方法，使用CCS软件以及Digital Signal Processor实现调幅调频信号的发生。
上传时间： 2016-03-20
上传用户：lht618
